KITACOGasket

I used it to replace the exhaust system on my ADV150 and it worked fine with no exhaust leaks.

There are no particular difficulties in installation. View detail

To replace Exhaust System

2Quantity:The set is reasonably priced, and KITACO offers peace of mind. View detail

1pc. is Smaller

The first one was a little smaller than the second one, so the Quantity:Set and it's falling down.
The other one was a good Just fit. View detail

Control voltage is too high.

After installation, I casually applied a tester to the battery and found that 16V was output!
I thought it was quirky and expensive, so I measured it and found that both Regulator and Battery
Idling (1600 rpm) The control was at 16V at 4000 rpm and 17.5V at 4000 rpm.
This is not usable!

Idling when I put it back in the OEM that I removed it from. (1600 rpm) The voltage was 14.5V at 4,000 rpm and 16V at 4,000 rpm.
Wasted... Worst of all... View detail

Number 100, number 100 ♪

I am purchasing this for my CUB.
When we did the bore up, we also installed Big cabPC20. Originally, the jets were already installed. I could have used it as it was, but I wanted to replace the jets while I was touching it.

This time, we decided not to replace the Throw and Needle, but only the MJ. The Jet system of the carburetor must be made properly, otherwise it will not give good results even if you touch it. It is difficult to confirm if it is made properly just by looking at it. I think trust is the best.

I have no problem with the installation. I checked with different numbers, and I enjoyed working with OEM because there is no doubt about the accuracy of the parts. It is a very important thing to have no doubt about the accuracy of the parts, and it reduces the amount of work. As a result, we decided to use No. 100.

I can't see the number on the Jet well with my old eyes, and I can write the number on the Large Jet with a thin Magic when I store it, but I can't write it on the Small Jet. There is no limit to the working time, so I look at it with my eyes. Magnifying glasses and reading glasses are good, but I imitate people of my age who are looking at small letters on their smartphone screens. When I store them, I put the package paper inside the Accessory Case to make it easier to read.

It's been around for a long time, but carburetor is fun once you start touching it. It takes a lot of time and effort, but the best thing is that it is fun. View detail

It's confusing.

When you purchase Slip-on Silencer.
Click here to purchase Gasket." I bought it together with the Full Exhaust System because there was a LINK with it, but it was a part that I would not use unless I was replacing the Full Exhaust System.
I learned from the Instruction Manual for the Exhaust System I received that a joint gasket is required for the Slip-on Silencer for the first time, so this product was a waste of time.
I would like you to put up a LINK to the recommended parts to purchase for the product. View detail

OEM same etc., inexpensive and good.

It was used for the second Exhaust System removal and installation.
The texture was almost the same as OEM.
Since it is Gasket, the feel is comfortable.
Quantity:1 Set of 2pcs. so it is also cosmetically pleasing. View detail

Good quality front fork dust seals!

These NTB Front Fork Dust Seals for the Honda MSX/GROM seem to be at least as good quality as the Honda OEM ones at a much lower price than the original ones! Recomended. View detail

OEM same etc.

Quantity:1 Set of 2pcs. to Spare when returning to OEM.
It's good enough View detail

No problem, but...

Coupler is a little bit small and a little bit tight.
At first I thought I had the wrong part number because it didn't fit. View detail

Quantity with high grip tire because it works well.:Set Exchange is a Recommendation

It definitely works better than the OEM Shoe, and the Feel when Brake is applied is good, especially the Rear, which makes me want to use it more aggressively.
Actually, before this DAYTONA made, I replaced the front and rear Brakes of the LITTLE CUB I used to own with Shoe made by a certain company, but the Rear started to squeal after one winter, not even a year had passed. It didn't affect the performance much, but when I was on the street, the Rear started to squeal. "Kikki!" However, the brake squeal stopped after I replaced it with a Daytona brake the summer before last. After that, I rode for a little more than a year without brake squeal.

The SUPER CUB110 is more powerful and heavier than the LITTLE CUB, so you can feel the effect of the SUPER CUB110. (Not as good as HUNTER and other disc brakes, of course.) The fluffy feeling is gone. I also feel that the front end sinks more deeply than the OEM when fully breaking.
Note that before replacing the Tire and Brake Shoe, the Rear sometimes locked up in Panic Breaking, but I think that was due to the OEMTire being poor. (The braking distance is not short because it locks)
After replacing the tires, I tried full breaking on a safe road, and both Front and Rear stopped firmly without locking. The fact that it did not lock up is probably due to the fact that I changed the tires to high grip BS BATTLAX BT-39SS at the same time. I am sure that the brake stops faster and shorter than before the change. I will not recommend this Brake Shoe with OEM Tire because I think it will lock up spectacularly! (Lol)

I have not ridden my JA44 so far, but I have replaced both front and rear with DAYTONA Shoe, so the braking balance is good. View detail

It's cosy.

I think the quality is the same as OEM etc. I don't know about durability yet. View detail

Cool grips

I bought these beautiful grips again - this time to replace them with a Honda Super Cub.
The handles are of excellent quality and are not expensive and fit perfectly. The replacement took a little time.

I bought these beautiful handles again - now to replace them with a Honda Super Cub.
The handles are of excellent quality and are not expensive and fit perfectly. The replacement took a little time. -------------------------------------------------- -------- I bought these beautiful handles again - now to replace with Honda Super Cub. Handles of excellent quality and are not expensive and are perfect. The replacement took a little time. I BUGHT Th, Beautiful Handles AGain - Now To Replace them with a Honda Super Cub. The Handles are of Excellent Quality and ARE NOT Expensive and Fit Perfectly. The Replacement took a Little Time. Powered by Google Translator View detail

Purchase Repeat

I bought Repeat because I used it before on my LITTLE CUB and it worked well. View detail

Product # 450-3021000

It was purchased for the Honda Super Cub to adjust the fuel mixture after installing the whale 75, size 85. Everything is great, I recommend it to everyone to purchase. Purchased for a Honda Super Cub to adjust the fuel mixture after installing kit 75, size 85. Everything is great, I recommend it to everyone for purchase. View detail

Hand Jet

It was purchased for the Honda Monkey to adjust the fuel mixture size 85. Everything worked out great, I recommend it to everyone for purchase. Purchased for a Honda Monkey to adjust the fuel mixture size 85. Everything fits perfectly, I recommend it to everyone to purchase. View detail

I was prepared, but ….

The Gasket could not be removed and was reused, although it was inexpensive and ready to go. View detail

CANOPY Brake switch replacement

Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
The replacement work was based on a You Tube video. View detail

Product # 25602

This time we needed grips for the "Suzuki Birdie". Once again, the grips from "Hunter" did not disappoint. Everything fits perfectly, the workmanship and material are top notch as always. I am very glad! View detail

To CT110 HUNTER CUB

Installed together with Exhaust System replacement. After the installation, there was no exhaust leakage. Don't forget to replace the Gasket when replacing the Exhaust System. View detail