Reviews
![[Short Lever] Brake Master Cylinder Kit [Horizontal Type 1/2-inches/Tank Separate Body Type]](https://img.webike-cdn.net/catalogue/images/105373/43336_TS.jpg)
Matching with Caliper
Purchased a 1/2-inches diameter short lever to replace the front caliper with a Brembo crab caliper.
Piston diameter 32mm in combination with Caliper (hydraulic pressure ratio 6.35) is
No Control at all with stiff Touch.
Piston diameter 34mm in combination with Caliper (hydraulic pressure ratio 7.17) is
Good Controllability, although a little softer than the preferred Touch.
If it were a standard Lever, would the former combination have been acceptable?
View detail
![[Stock Lever] Brake Master Cylinder Kit [Horizontal Type 1/2" / Tank Separate Body Type]](https://img.webike-cdn.net/catalogue/images/105373/61739_TS.jpg)
Used for MAJESTY 125 FBrakes custom
The MAJESTY125 and R1-Z have the same 83mm Pitch of the front brake caliper, so I used the R1-Z's caliper and changed the front brake to 4POD to strengthen the brake. So, I wanted to lower the Piston size of MASTER, and I wanted to be able to adjust the lever play by Dial as well as CB1300 Caliper, and I wanted to use a short lever. I also wanted to use short lever, so I replaced it with Nisshin's MASTER.
As expected, the brake has improved in both touch and braking power due to the MASTER's smaller-diameter piston size,
Now I have a performance problem on the Caliper side and want to replace the Caliper with the SumitomoCaliper from TZr250 after 3MA or the Nisshin caliper with 83mmPitch released from TZ125, TZ250 and AdvantageNisshin in the 90's. I'm looking for a new caliper.
View detail
A little short, a little thick
I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people.
View detail
Good product
Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
It looks better now.
I put it on because it stands out from the OEM. View detail
Good variety of color variations
Standard NGKPower cable, used for CUB.
Speaking of NGK, I had always thought of Red and BlueCable images, but I was surprised to find that NGK has a wide variety of color variations.
I was curious about the Yellow color code + BlackCap, so I bought it, and the actual color was a nice bi-Bit color as well.
View detail
ALCAN hands iGrip
I have used it for VTR250 and MT-03, and I bought it again this time. The color is Orange red to match the body color, and it is a good accent for the handlebar. When I installed it, I used a small amount of glue to prevent shifting and decided not to use wiring. View detail
We can only be thankful that we have Parts….
It functions as a Blinker Bracket.
The shape is completely different from that of the OEMBracket.
That's the fate of Ripro products, we should be thankful that Parts is sold.
We do not recommend this product for the finicky or nervous person.
View detail
Necessary and sufficient efficacy
I am using it with KawasakiZ1.
We are on Double disk with OEMCaliper.
Is it thanks to the Shim on the back of the Pad?
No squeaking so far.
Braking force, but it does not perform Race.
It works well enough for the TouringLevel's muddy driving.
If you say that this Pad does not stop, then that is too much Speed.
View detail
Fits: KAWASAKI 500SS Mach III (H1), KAWASAKI H2, KAWASAKI KH, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS), KAWASAKI Z750FX
I'd rather buy a Besra ….
It is useless unless you hit Pin on the back of the Pad and attach it.
Then you should buy a Pad with Shim from Vesra.
View detail
I wanted Cap.
I purchased this product to connect to the Ignition coil in Mukawa and wanted to unify the colors.
Cutter off the adhesive bonding the Cap to the cord, peel off the Cable outer skin of the Mukawa Ignition coil, insert it, and fix it with adhesive, and you are done.
The excess Cable of the product in question is used in place of the Cable attached to the OEMCoil.
This would have been unnecessary if caps in a variety of colors were available, but they are not.
Even if only the cable is replaced, the idling is stabilized and the long-used OEM product is refreshed.
View detail
Power cable & elect. module Dev'moto
Bonjour from France Thanks you for quick shipment of my order , i fixed it on ma yam sr 125 in addition of a new electronic module Dev'moto(made in France) with an iriduin plug already than replace the TCI -dead-:( the result is more better ( already too with the new module) cold cranking + little better torque at low rpm, and more i could reduce my idle setting ... so very happy with my purchase ... voilà ! View detail
good choice
I bought it after seeing a review that you often replace it with a set with Takegawa reinforced coil. I bought any color because it was hidden in a cowl, and I connected the ngk power cable with the Takegawa reinforced coil and installed it. I had to cut the length and install it, but I thought there would be some loss, so I just connected it. It starts up well and I think it's effective in output. Thank you. View detail
SD-401 should be called the old one.
Using it as it is, it is like that to begin with, but even the double disk on the 650RS W3 only works vaguely.
Especially with Solid's Rotor without Slit, it is the worst in the rain, it doesn't work as well as it should.
This is an area where I would like to ask manufacturers if they can do something about the friction material.
We are working very hard to stop squeaking and increase braking power, but the methodology is a secret.
To increase braking force with the old Tokico Caliper, the Caliper design philosophy must be revised.
Also, the Package was changed from the one I purchased this time, and the Pad has a groove, but the inside of the Pad is not the same as the one I purchased this time. (Fixed side) the groove is in the radial direction of Rotor, but the outer (Piston side) But unbelievably, the grooves are circumferential.
I would like to ask Vesla what he is thinking on this point.
View detail
affordable price for good quality product
these item is very useful for those who want to get perfect spark for the bike - the Cables are designed for the serious racing enthusiast and feature high temperature silicone outer jackets, solid copper wire strand core and high temperature resistor covers, leading to improved engine performance View detail
Fits: KAWASAKI BALIUS [BALIUS] I B1-B4, KAWASAKI BALIUS [BALIUS] I B1, KAWASAKI BALIUS I B4, KAWASAKI BALIUS [BARIOS] II B1-B4, KAWASAKI BALIUS [BALIUS] II B1, KAWASAKI EL250 E1-E2, KAWASAKI BALIUS [BARIOS] II B4, KAWASAKI EL250 E1, KAWASAKI EL250 E2, KAWASAKI ELIMINATOR 125 [ELIMINATOR] A1-A2, KAWASAKI ELIMINATOR 250 [ELIMINATOR] B2-B3, KAWASAKI ELIMINATOR 250 [ELIMINATOR] B2, KAWASAKI ELIMINATOR 250 [ELIMINATOR] B3, KAWASAKI ER500 A1, KAWASAKI ER500 A1-A3, KAWASAKI ER500 E1-E3, KAWASAKI ER500 A3, KAWASAKI ER500 E1, KAWASAKI ER500 E3, KAWASAKI ESTRELLA [Estrella] B
Mounted on ZZr250
Mounted on ZZr250
SelfStir was a tough car model,
After replacing it with this one, that has been alleviated.
I guess it is a standard Custom for ZZr250.
View detail
![[STD Lever] Brake Master Cylinder Kit [Horizontal Type 1/2-inches/Tank Separate Body Type]](https://img.webike-cdn.net/catalogue/images/105373/61758_TS.jpg)
long vowel mark (usually only used in katakana) (>ω<;)
Converted to my son's BALIUSA5, which had an air leak from the MASTER.
I thought about installing the Radial master, but I decided to go with the ZrX1200 DAEG because it is expected to be replaced by the ZrX1200 DAEG next year, so I decided to go with this one for cosmetic reasons.
Tank Separated Type is good for a different atmosphere. (? ・ ・?)
For the price, Touch was fine and a good buy!
However, it may be a little long for Mr. Balius in the standard lever….
It was sticking out of the handlebar, so I replaced it with a short lever. (Polish)
I should have measured the length before purchasing and selected the short lever type lol.
View detail
Fits: HONDA SUPER CUB110PRO, HONDA TACT, KAWASAKI KX85, KAWASAKI KX85-II, KAWASAKI Z650, YAMAHA PW50, YAMAHA YZ250, APRILIA RX50 (Aprilia), APRILIA SCARABEO50, DUCATI 900SS, DUCATI 906PASO, DUCATI MONSTER400, DUCATI MONSTER400, DUCATI MONSTER620, DUCATI MONSTER620, DUCATI MONSTER620, DUCATI MONSTER900, DUCATI MONSTER900, DUCATI SS800, DUCATI SS900
Standard Custom
High Response compared to OEM.
It was easy to install
View detail
Fits: YAMAHA Cygnus X SR, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI SV400, SUZUKI RMX250S, SUZUKI RMX250, SUZUKI RG200, SUZUKI GSX250S Katana, SUZUKI GS400E, SUZUKI GS125E Katana, SUZUKI GS125, SUZUKI DR250S
Great!
Replaced an OEM Master Cylinder with a BALIUSA5 that developed an air leak.
The color is Black×Black.
I was relieved to find that the front brake, which does not bite the air, was properly connected to the Snap. (? ・ ・?)
The only problem I have with this vehicle is ….
The tank is placed too close to the HandlebarCenter and may be covered by the Tachometer.
Well, I can just buy a Bracket at Home center and move it to a new location, lol.
I have a shabby blog, if you are interested! (^_^;)
https://enjoy-motorcycle.blog.jp/
View detail