Reviews
I feel like I have more Control.
Inner rotor is made of material.:The design is close to OEM, so I don't feel any discomfort after the replacement. The durability (life span) is yet to be determined.
This is just my subjective opinion, but so far I can't find anything wrong with it. I wish the price was a little lower, but I think that is too much to ask for....
View detail
Brembo radial master
SEA BASSRGV250Γ (VJ22A) It is used for
We found a Fluid leak from the OEM Master Cylinder due to deterioration, and were torn between Overhaul, a new NISSIN, or a YamahaOEMbrembo, Get me the best one you can." This is why we chose this product.
The OEMCaliper piston diameter is an opposed 4-pod 30/34mm double disk, but Radial master recommended 17mm or 19mm, but I prefer a firmer touch, so I finally chose 19mm.
The original hose was a Swage line mesh hose, and the handling was different from the OEM hose, so the hose was simply attached with the supplied banjo bolt.
The tank bracket, tank, and hose were purchased separately, and the brake switch was installed using the Emon Flat Terminal instead of the Bullet Type Terminal, which came with the brembo wiring, because we did not want to change the OEM wiring. The brake switch was installed using Emon's Flat Terminal instead of the Bullet Type Terminal.
I was worried about interference with the cowl when installing the tank, but there was no problem, although the clearance was about 5mm when the handlebar was fully cut.
Air venting is very easy because of the Bleeder Bolt on the MASTER side.
As for the key performance, even my insensitive self could feel that BrakeTouch was improved over OEM.
I am not sure if this level of specifications is necessary for touring on public roads. (Lol)
However, my impression is that it is a little harder than I expected.
It's not a Level that has problems of course, and even at 19mm, it's definitely significantly better than the OEM Master Cylinder. (OEMTokico) And I think there is also the issue of compatibility with
I have not tried it, so I can only imagine, but I think 17mm would be fine.
The lever is also infinitely adjustable, so you can grip it from your best position.
Finally, as for the appearance, it is very beautiful, but it is too beautiful for old cars and floats a bit. (Lol)
It was a bit expensive, but I felt the price was well worth it.
View detail
Fits: BUELL S3, KAWASAKI GPZ1100F, KAWASAKI GPZ750F, KAWASAKI Z800, KAWASAKI Z750, KAWASAKI Z1000, KAWASAKI W800, KAWASAKI W650, KAWASAKI W400, KAWASAKI H2SXSE+, KAWASAKI GPZ750, KAWASAKI GPZ1100, HONDA VTR1000F, HONDA VFR800, HONDA VFR1200, HONDA RVF750K, HONDA RVF750, HONDA NC700S, HONDA CBR1100XX, HONDA CBR1000F
I purchased the Motorcycle Cover because it was out of date.
The handling is very easy and the double structure is very good for a Full Cowl Motorcycle Cover.
Also, GSX1300R HAYABUSA (Type 2) I was able to install the Cover with the GIVI Top Case Bracket still in place.
View detail
I was attracted by the Gold color and bought it, but… I was not sure if it would work or not.
I tried replacing it with a Gixxer 250 Rear pad, but the braking force is much weaker than OEM and relies on the Front brake. it may be a compatibility issue with Caliper, but I can't get used to it, so I'm going back to NORMAL. View detail
Genuine Brembo 19RCS Corsa Corta fitted to YZF-R1
The YZF-R1 came in wanting to be transitioned onto a track related bike so I went to work on the braking system. One of the first things I wanted to change was the annoying stock master cylinder. Obviously, Brembo was the way to go. I decided on this one as it fitted with the specs of the bike in mind. Finding the correct master cylinder was not hard but there were a few choices but I went for this one, the 19RCS Corsa Corta in the end. It had all the requirements I needed so it went in my basket. I had a few other parts and the shipping was reasonable for what I had. EMS got my order to me in 5 days. The master cylinder came with the standard stock lever length which was perfect for my needs. It is the 18 x 20 one so works good with the floating calipers on the bike anyway. It came in the Brembo box and also came with a few copper washers. I had already sourced the HEL line that would make this all work. The master cylinder is a real piece of kit and fitted really well with the bike and the instrument cluster I was leaving in situ. Not a hard job once you have all the parts together. This master cylinder is awesome and so much better than the stock one. Oh and by the way, looks the nuts. There are just so many adjustments that you can definitely find the right setting for your liking. Thanks Webike for the great service you provide. View detail
At first I was puzzled by the difference in Touch.
I was happy with the OEM Nisshin so far, but since the Caliper is brembo, I thought it would be better than what I have now. I bought it because I thought it would be better than what I have now.
I am not a fan of snaps and touches, so I was a bit confused at first, but I thought the Lever ratio 18 would be good for control. I would like to try various things with Winding when the road surface temperature rises a little more.
View detail
Ultimate Streetbike Caliper
Billet monobloc Stylema calipers , the dust seal equipped beauties , ready to enhance your ultimate streetbike / track day / custom build . When Brembo announced the billet version Stylema , I was very interested in the fact these calipers bridge the technology gap between full race monobloc calipers and street use calipers , so I knew I had to own a set to try them out . The traditional cast Stylema is already the best factory fitted premium caliper , and rightly so , but these precision billet masterpieces deliver truly next level braking performance . I have fitted my set to 2023 H2 Ninja , and the big speed washes off with 1 finger control , highly recommended . View detail
Genuine Brembo Radial Brake Master Cylinder (19 x 20) Stock Lever
I was working on a bike that was being transitioned into a track bike. One of the first things I wanted to changer was the annoying stock master cylinder. Obviously, Brembo was the way to go. I decided on this one as it fitted with the specs of the bike in mind. Finding the correct master cylinder was not hard but there were a few choices but I went for this one in the end. It had all the requirements I needed so it went in my basket. I had a few other parts and the shipping was reasonable for what I had. EMS got my order to me in 5 days. The master cylinder came with the standard stock lever length which was perfect for my needs. It is the 19 x 20 one so works good with teh floating calipers on the bike anyway. It came in the Brembo box and also came with a few copper washers. I had already sourced teh HEL line that would make this all work. The master cylinder is a real piece of kit and fitted really well with the bike and the instrument cluster I was leaving in situ. Not a hard job once you have all the parts together. This master cylinder is awesome and so much better than the stock one. Oh and by the way, looks the nuts. Very pleased with this part. Thanks Webike for the great service you provide. View detail
Front brake replacement
The feel, the texture, the design, this is brembo! View detail
I knew it! Brembo!
The Pad that originally came with it was getting very thin, so we replaced it.
At first, I wondered if the stop was worse than before. I thought that it was worse than before, but I drove on.
After running for a while and some heat, it settled down to a smooth stop, just the way I like it.
KTM is a BYBRE Caliper, which means that the braking power is fine, but until now it has felt like it was working too hard for me with the kakkun.
If you are asking if brembo's Pad is unstoppable, rest assured that it is not at all.
The brake system is brembo after all.
View detail
Cool
I can't compare it with OEM because I replaced it right after I bought the used car, but it has good control with Brembo caliper and it works perfectly for my driving style. And above all, it is cool. I think I will be able to get used to it soon if it is not too much different from the OEM. View detail
safety
DUCATI SCRAMBLER2020 Rear Wheel Brake
The original pad is from bremboOEM, but we replaced it with this one.
When I first started using it, I was worried that it wouldn't work…? But as I let it sink in, it worked just as described. It works as long as you hold it/step on it." I feel that it is more Mild than OEM.
I think it is suitable for running like adjusting the speed with the rear brake while keeping the RPM low with a tight corner.
As for durability, I don't know since I've only just started using it.
View detail
Reliable Brand
Brembo is now the standard equipment on the upper models, but the red color is very noticeable because of the fine detail on the Brake Pads.
SPMODEL is a product that is not intended for racing, so it can be used on public roads.
The product itself is easy to Control and feels good.
View detail
Pure high performance with no extra features
Of the many brembo Master Cylinders, this was the first to be marketed as a RadialPump.
Strictly speaking, the Cut-out's used for Works machine "RACING" At the time, it cost about 80,000 yen, so only a few wealthy people could afford it, and this is a low-priced version for the general public with a non-cut-out surface finish.
It originally designed for WorksRacer The car is a racing exclusive part, so there is no consideration for the installation of a stop lamp switch, which is required for driving on public roads.
(When it was first released, it was prohibited to drive on public roads.)
It's a good time because now they come with a hydraulic stop lamp switch for public road use.
Nevertheless, hydraulic switches use a portion of the hydraulic pressure to activate the switch, which defeats the purpose of RadialPumping, which is to improve lever touch.
I would not want to use it if possible.
Mechanical Switches are available from various companies, but these are also a bit iffy, as they force you to attach very complicated and delicate objects.
I have modified Lever to operate MechanicalSwitch in a completely different way because it is very intrusive, especially if I frequently maintain the Lever area.
Such Hardship to use public roads." Apart from the "RaceParts", the original RaceParts were very serious RaceParts, so the effect is very effective! The lever touch improves unbelievably.
To give you an idea of the degree of improvement, if the previous operation was a 10-step control from release to lock, it would be 10 times more detailed, with 100 steps of control.
Whereas operations that I thought were full Brake were actually only available up to 9 due to the change to 9→10, with this product I can confidently grip up to 9.9, like 9→9.1→9.2→9.3 ... and so on.
As a result, Brake works better even though changing the Master Cylinder should not make Brake work better.
How to mount the reserver tank, the brake hose routing is different and needs to be redesigned, the banjo bolt pitch is 1.0 (and the brembo requires a shorter bolt than usual because the screw hole is shallow), the stop lamp switch needs to be modified, etc. (In addition, brembo requires a shorter bolt than usual because the screw hole is shallow), the stop lamp switch has to be modified somehow, and some ingenuity and modification is required to avoid contact with the cowl and meter.
A more powerful successor is also on the market, but it is loaded with extra equipment and heavier than ever.
If your goal is purely to improve lever touch, this is the lightest weight one.
I wonder if the Body rigidity is higher, or why I feel the Touch is better than the high-end version of CNCCut-outMODEL....
View detail
Genuine R&G Toe Guard for Honda CBR600RR 2010
R&G are a great brand and provide some cracking protection for all models of bikes. They sell a lot for the CBR600RR as these bikes do hit the deck often on track. This toe guard is an essential part when riding on a track as you just do not want your foot or anything in that area in the event of an off. Finding this part number was not too hard as this version does fit a lot of different models and manufacturers. The price from Webike was good value and add with the other items in my basket, I got them all shipped together to save on teh shipping cost. EMS got my order to me in 5 days from shipping. The toe guard is super strong and the bolts that attach this to the swing arm are also really strong. As this is aluminium, it will take a fait bit of hsammer before it gives up the ghost, I know this as I previous;y had one and it took some damage before it eventually snapped. The bolts are threaded really well, the painted finsih is really good and flawless too. Fitted in no time. Very pleased with this and now it will be good to go on the track once again. View detail
Fee Ring changes!
Just the fact that I changed to brembo makes me happy!
But when I changed Caliper, it was difficult to feel the Fee Ring change, but Radial brake master changes a lot!
Also, it is better to change the clutch lever to CORSA Corta Lever, which is easier to grip and gives a more unified feel.
View detail
Two layers are recommended.
Cover is 2L Size, body is XSR900 (RN56J) The parking lot is used for open-air parking.
When I bought a new car, the dealer gave it to me as a purchase bonus and I was using it, but I had been using it without tightening the String at the hem, and there was a hole where the footpeg hits, probably from the wind, about the second year of use.
I bought the same product because I was not sure about the Size feel of the other company's product, as the dirt that clearly shows the Cap part of the Tank on the Others was floating around and I thought the open hole would widen if I continued to use the product.
However, the first Cover was still usable, so we decided to use two pieces with the new one inside.
As a result, two layers are good. The old outer cover is getting a large amount whiter in the front blue area due to sun damage, but the inside is still as blue as new and the fabric is still soft.
As a Motorcycle Cover, it is convenient that there is a part to put a Wire lock and a Chain lock through the front and rear Wheels. There is not just a hole, but a notch, so it is easy to put the locks through.
Size feeling is that if you don't squeeze the String at the hem, you can't get the size you want, especially Quantity.:Pair (for Left and Right) It may be good for those who want to cover it completely as the hem is just hanging on the ground with excess hem on the sides.
Instead, I don't think moisture will escape, so if you are concerned about moisture, I think the F Type with Ventilation would be better.
View detail
Great looks. as a cap bolt….
Do not over-tighten or apply Screw lock agent by mistake, as the material is material and will quickly lick the hex holes.
I want to install it firmly because it is for fixing Stay which supports important parts around Handlebar ….
View detail
Easy to use with OEM Fee Ring
Some pads work with a Snap at the moment of grip, but a pad that works too hard is nerve-wracking when you want to slow down while dragging the Brake a little.
The Pad here has a Fee Ring that is close to OEM and is gentle at the beginning of the grip, making it easy to control the Brake.
Of course, it works well if you hold it firmly.
Breaking has become more enjoyable after adding this pad because it works consistently in a sensible speed range, regardless of weather conditions.
View detail
High quality and very pleasant to use.
I was using a 4 year old Motorcycle Cover (about 5,000 yen at Home center), but it started to become brittle after about the 3rd year, and when I took it on and off, I could not get it off. Paste Tape when you run out." However, it has finally deteriorated to the point that even when gently attached, it will break off along the fibers.
The last one was so full of taping that I couldn't tell if it was a cover or a tape.
Motorcycle is stored under a carport so it wasn't in direct sunlight or exposed to rain, but I guess that's the life of the Cover.
When I took the new Cover out of the box, it was the same Silver as the previous Cover, but I felt a thicker and shinier Bird feeling (Well feeling, not crumbly). 。 Durability looks promising.
Size is 2L. And it is just the right size, not too large and not too small.
The Wire lock holes are also set in the front and back, and there is a cord that can be used to squeeze the hem with One-touch for ease of use.
View detail