Reviews
Fits: HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CT110 HUNTER CUB125, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB C125, HONDA Dio 110, HONDA LEAD 125, HONDA PCX 125, HONDA PCX 160, HONDA PCX ELECTRIC, HONDA ADV 150, HONDA HORNET250, HONDA HORNET600, HONDA CB 125R, HONDA CB 250R, HONDA CBR 250RR, HONDA CBR 600RR
Easy to hang and wind resistant. Very good.
I use this Repeater on my CT110 HUNTER CUB and GB250 CLUBMAN. It is my favorite.
I bought it last year when I bought a CT110 HUNTER CUB, because I was planning to add a front carrier and a RODCarrier to it. I am sure it will be a good reference for those who are considering purchasing it.
The front carrier is made of DRC, the largest class, and is fixed at the most forward position, so the front of the handlebar is considerably longer than in NORMAL, The height of the LeftFront section of the Rear Carrier is 10cm higher than the Seat. The lower part of the front wheel and Quantity:Pair (for Left and Right) As you can see in the photo, I can close the RearFastener to the very bottom, even with the bottom rope tightened quite a bit. I live in an area that is occasionally exposed to strong winds, and the Seat has never rolled up.
Also, I have been using it for over a year now and it has not deteriorated much. (There is a short period of time when the parking Space is in direct sunlight.) Not much dirt on it. (It has a roof, so it is virtually dry even in the rain.) and I have never washed the surface with water. I am very satisfied.
I bought it for GB250 CLUBMAN almost one year after CT110 HUNTER CUB. It is rather a little bit large, so the front wheel lower part and the quantity of the front wheel are a little bit smaller than the original size.:Pair (for Left and Right) The Adjuster rope at the bottom is fully squeezed. There is still room to spare, but not so much that it will flip up in the wind, so we are not worried at all.
Perhaps if it were exposed to rain and direct sunlight throughout the day, the evaluation of deterioration might change, but I cannot comment on that.
View detail
Fits: Others Universal, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUBC125, HONDA CROSS CUB50, HONDA BENLY50, HONDA BENLY50110, HONDA glom, HONDA MONKEY125, HONDA DAX125, HONDA LEAD50, HONDA LEAD 90, HONDA LEAD 100, HONDA LEAD110, HONDA LEADEX, HONDA APE 50, HONDA APE 100, HONDA DIOCesta, HONDA XR50 MOTARD, HONDA XR100MOTARD
Exactly to MONKEYGROM
It is Exactly for 125cc Minimoto. It is thick, waterproof, and will not fade. It is quick to hang, and the center clip prevents flapping, even in strong winds.
The holes for locks on the front and back are also well and not frayed.
The black color is inconspicuous at night and plays a role in security.
View detail
I can last three years
In 3 years, the Black will fade and become White, and it will catch and become ragged.
It needs to be replaced periodically.
Exhaust Guard is included in the price.
View detail
Formative Lantern CUB
Changed from high quality plug to Standard Plug BP5HA I can't see much change in the expensive product and it seems to be covered with black. View detail
I'm satisfied
I had been interested in MOTO DX for some time, but had not been able to try it on my ZRX1100 because it was not available. I have just purchased a new Z125PRO, and although there was nothing wrong with the original Plug, I decided to give MOTO DX a try right away.
The replacement work is not particularly difficult, since all you have to do is to replace the plug. In fact, the Z125PRO can be accessed immediately, and since there is only one plug, it was one of the easier ones. However, it is not difficult, but if you twist off the plug by over-tightening, you will be in trouble, so be careful if you do it by yourself. I did it before with a ZRX1100, and it was a chilling experience. Fortunately, I was able to remove part of the twisted off plug using the Extractor, but I almost had to reverse the upper part of the engine. When tightening the plug, it is necessary to check the tightening torque carefully and close it with a torque wrench, or if you tighten it by hand, you need to tighten it more or less.
I quickly replaced the plug, put the plug cap back on, and did a test run. First of all, I felt that the car started up clearly better, and when I started driving, I felt that the acceleration was a little stronger. I do not yet know the effect on fuel consumption or durability, but I hope that the durability will be as good as the manufacturer claims. In general, I believe that the replacement has had a positive effect.
MOTO DX is more expensive than most plugs, but I found it to be a reasonably effective product. However, for a single-cylinder vehicle like the Z125PRO that only needs one, the price was right for a trial run because the hurdle is lower.
It is a good product that I would recommend without omission to my friends who drive vehicles with the settings.
View detail
Titaniumium color!
Small but finely crafted
Luxury that you can feel in your hands
Worth the Gold!
View detail
There was no one with Level gauge.
The OEM Product was not strong enough, so it was replaced. After installation, I found that the flange surface is narrower than the OEM Product, so there is a gap between the OEM Product and the engine side. I would have liked to have had a product that fits Exactly. View detail
As expected of DAYTONA
Was the installation difficult?
pimping
How was your experience with it?
It's going to look different
View detail
It was EXACTLY!
I purchased this to replace an OEM Oil cap groove that was broken.
It was Exactly in JA10!
View detail
Dress-up in a casual way
It can be dressed up casually.
I am satisfied with the quality of the product.
It would be better if it were a little cheaper.
View detail
The oil filler cap is very convenient to use and decorate
Daytona brand is a famous brand in the production of spare parts for motorbikes from engines to decorations. In particular, the product set of oil cap, reservoir cap and bar ends comes from Daytona premium, I feel the quality is improved compared to normal Daytona. With this set of oil caps, compared to the original cap, I find that it is not only used for decoration with many colors to choose from, but also can be easily opened and closed to make changing the oil easier. With a normal OEM oil cap, I usually spend about 2 to 3 minutes opening and closing the oil cap. With the Daytona oil cap, it only takes 30 seconds to do that. View detail
Oil Filler Cap
Changed to Green Light or Gold. View detail
It's always this
I always keep it as a spare. It's inexpensive, the quality is good, and it's a standard item. View detail
To my friend's Motorcycle.
Ordered for installation on a friend's Motorcycle.
The installation went without any problems.
I was thinking that the tools would be a Drill and a Hole saw.
Hole saws are expensive to buy new, so if you don't have one, you should ask a Motorcycle shop for one.
View detail
For Grip heater
I bought this for my Grip heater and it is easy to install as long as you can remove the front cowl. I am satisfied with it. View detail
Replaced from heavily worn Plug
I had a symptom of poor cold start and ordered it with the intention of replacing it, no questions asked!
The work was completed without difficulty since it was a replacement for the same one in the OEM adopted Plug.
I removed it and compared it to a car with about 50,000 km on it, and I'm guessing that it has never been replaced.
The photo was taken without a second thought because of the amount of wear and tear.
After replacement, starting performance was clearly improved!
I reaffirmed the meaning of periodic replacement.
View detail
Fits: HONDA CT110 HUNTER CUB125, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB C125, HONDA PCX 125, HONDA PCX 160, SUZUKI ADDRESS110, SUZUKI Address125, YAMAHA AxisZ, YAMAHA CYGNUS X, YAMAHA CYGNUS Gryphus, YAMAHA NMAX125, YAMAHA NMAX155
Size fits!
Bought this for my Motorcycle with CROSS CUB box! It's thinner than the old one, but it's easy to hang! The best thing is that I can squeeze the hem. It is very good to be able to squeeze the hem. It wraps the motorcycle tightly! The price is twice as much as the previous Cover, so I expect it to be durable! View detail
PetitCustom
[How is it used?
It has a custom feel.
Was the one you received as per Image?
As you wish.
Was the installation difficult?
It's very easy.
How was your experience with it?
I like it at One point.
[Included Parts:were they on?
Hexagonal Lunch is not enclosed.
[Was there anything that disappointed you?
None
Other items that would be helpful
Remove Oil cap for NORMAL It is easy to install.
I wish it had come with a Wrench, but ….
The first step of the Custom project was the installation of the new system.
View detail
Peace of mind that it is made by MORIWAKI
The peace of mind of being made by MORIWAKI.
I don't have Level gauge, so I guess I'll go back to OEM just in case I need to replace Oil.
So far, no problems at all.
View detail
Fits ZX-4R
It can be attached to ZX-4R without any problem. View detail