Matching with Caliper

Purchased a 1/2-inches diameter short lever to replace the front caliper with a Brembo crab caliper.

Piston diameter 32mm in combination with Caliper (hydraulic pressure ratio 6.35) is
No Control at all with stiff Touch.
Piston diameter 34mm in combination with Caliper (hydraulic pressure ratio 7.17) is
Good Controllability, although a little softer than the preferred Touch.

If it were a standard Lever, would the former combination have been acceptable? View detail

Size is Exactly

The Size is Exactly and does not flap. It withstood a typhoon by tying up. It is also easy to lock.
Consumables, so they need to be replaced regularly. View detail

NTBBrake Pads

I think the cosmetics are good. I expect it to be durable. View detail

Used for MAJESTY 125 FBrakes custom

The MAJESTY125 and R1-Z have the same 83mm Pitch of the front brake caliper, so I used the R1-Z's caliper and changed the front brake to 4POD to strengthen the brake. So, I wanted to lower the Piston size of MASTER, and I wanted to be able to adjust the lever play by Dial as well as CB1300 Caliper, and I wanted to use a short lever. I also wanted to use short lever, so I replaced it with Nisshin's MASTER.

As expected, the brake has improved in both touch and braking power due to the MASTER's smaller-diameter piston size,
Now I have a performance problem on the Caliper side and want to replace the Caliper with the SumitomoCaliper from TZr250 after 3MA or the Nisshin caliper with 83mmPitch released from TZ125, TZ250 and AdvantageNisshin in the 90's. I'm looking for a new caliper. View detail

Good product

Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail

1P2014

The head lamp on my Honda Little Cub burned out. I liked the price and parameters of this lamp (not much power does not overheat the cartridge). Everything turned out to be good in quality, the lamp works perfectly. View detail

Anyway, it's bright.

The ADDRESS V100 has a reputation for having a dark headlight to begin with. (1994 model) attached to the
I am impressed that I can now see in front of me when driving at night, but in general, the light intensity is just normal.
Still, it is hard to believe that it is +6.5W, and you can feel the difference between just a light bulb and Halogen very clearly.

We do not yet know how durable it will be, and we do not know if the increased power consumption will affect the battery charge.

Well, even if the Battery goes up, you won't be able to leave because the KICK is on.

Its Risk is unknown, but I think it is worth changing it once for V100Owner who has problems with Headlight.
That's how bright it is! V100 is w View detail

Hiccuped when I saw the OEM price...relieved when I saw the NTB price.

Used for StemOH on SEROW225.
2Quantity of balls:2pc. I needed a set, and when I bought them from YAMAHAOEM, they cost about 100 yen each and the total was over 2,000 yen. (It's not that YAMAHA is looking at my feet, it's just that I pack them one by one.)

I don't know if it is a perfect circle or a perfect sphere with that level of accuracy, but for now, it is perfectly fine. View detail

Easy installation, no brightness problems.

Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness. View detail

WhiteLight and good looking!

It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light. View detail

Bright and low power consumption

I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling. View detail

XG250 TRICKER

I use it on my XG250 TRICKER.

The Motorcycle Cover is a consumable item, so this thickness is sufficient for this price. View detail

Genuine DID 420NZ3 Gold Spare Chain Link

I do not really use these too often as they are basically one step up from a push bike chain anyway. But, it is always good to have them in stock just in case a customer needs one. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get a not seem to get the white grease packet in this size chain but that's ok, I have a lot of these anyway. The chain link is very well made, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail

I think it is necessary and sufficient.

This is just my personal opinion, but I think it is not a PeLePera, and considering the price, I think it is satisfactory enough. View detail

I put it on my RG 50Gamma.

It's just like changing a light bulb.
There is no problem View detail

Cool grips

I bought these beautiful grips again - this time to replace them with a Honda Super Cub.
The handles are of excellent quality and are not expensive and fit perfectly. The replacement took a little time.

I bought these beautiful handles again - now to replace them with a Honda Super Cub.
The handles are of excellent quality and are not expensive and fit perfectly. The replacement took a little time. -------------------------------------------------- -------- I bought these beautiful handles again - now to replace with Honda Super Cub. Handles of excellent quality and are not expensive and are perfect. The replacement took a little time. I BUGHT Th, Beautiful Handles AGain - Now To Replace them with a Honda Super Cub. The Handles are of Excellent Quality and ARE NOT Expensive and Fit Perfectly. The Replacement took a Little Time. Powered by Google Translator View detail

Rear Sprocket purchased with tooth count change

Purchased to change the number of Chain pieces when changing the number of teeth on the Rear Sprocket. clip type is easy to adjust as it can be removed as many times as needed. View detail

It looks better now.

I put it on because it stands out from the OEM. View detail

Good variety of color variations

Standard NGKPower cable, used for CUB.
Speaking of NGK, I had always thought of Red and BlueCable images, but I was surprised to find that NGK has a wide variety of color variations.
I was curious about the Yellow color code + BlackCap, so I bought it, and the actual color was a nice bi-Bit color as well. View detail

Chain assembly

The chain was stretched, so I cut it and used it for reassembly.
Installation does not seem to be that difficult since it is a Clip. View detail