Reviews
Matching with Caliper
Purchased a 1/2-inches diameter short lever to replace the front caliper with a Brembo crab caliper.
Piston diameter 32mm in combination with Caliper (hydraulic pressure ratio 6.35) is
No Control at all with stiff Touch.
Piston diameter 34mm in combination with Caliper (hydraulic pressure ratio 7.17) is
Good Controllability, although a little softer than the preferred Touch.
If it were a standard Lever, would the former combination have been acceptable?
View detail
Maintenance.
I have not used it yet but the Bolt on the R1 has rusted so I bought it to replace it.
I would recommend everyone to replace it before this happens because it will make the Brake less effective. LOL!
View detail
Used for CRF250L. A little more emphasis on acceleration.
By changing the rear to 42T, the speed range below 50km/h has become easier to use. Of course, the RPMs become a bit louder at speeds above 60 km/h.
Speed healers are used, so speed errors have already been corrected.
View detail
Good product
Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail
1P2014
The head lamp on my Honda Little Cub burned out. I liked the price and parameters of this lamp (not much power does not overheat the cartridge). Everything turned out to be good in quality, the lamp works perfectly. View detail
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
As expected of DAYTONA
Was the installation difficult?
pimping
How was your experience with it?
It's going to look different
View detail
It was EXACTLY!
I purchased this to replace an OEM Oil cap groove that was broken.
It was Exactly in JA10!
View detail
Exactly to MOTARD as well.
Bought this for my drz400. For a long time, I had been wearing the one for my previous Large Motorcycle, but it was not so good because it was too loose. This time I bought it because it said "for Off-Road" and I am satisfied with the just fit. I also like that the lower part can be closed with a string. View detail
Dress-up in a casual way
It can be dressed up casually.
I am satisfied with the quality of the product.
It would be better if it were a little cheaper.
View detail
Genuine DID 520ERVT Replacement Chain Link
I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERVT is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. I keep the rivet link type and this clip joint type but had ran out of this version, hence the purchase. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
I'm not sure about the electrical system, but ….
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
These are the Parts that are required when using LEDs with DRC's Kit.
View detail
The oil filler cap is very convenient to use and decorate
Daytona brand is a famous brand in the production of spare parts for motorbikes from engines to decorations. In particular, the product set of oil cap, reservoir cap and bar ends comes from Daytona premium, I feel the quality is improved compared to normal Daytona. With this set of oil caps, compared to the original cap, I find that it is not only used for decoration with many colors to choose from, but also can be easily opened and closed to make changing the oil easier. With a normal OEM oil cap, I usually spend about 2 to 3 minutes opening and closing the oil cap. With the Daytona oil cap, it only takes 30 seconds to do that. View detail
WhiteLight and good looking!
It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light.
View detail
Bright and low power consumption
I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling.
View detail
Genuine DID 520 Replacement Chain Link
I always like to have some of these in stock in case opf any issue during fitting different chains. The DID 520ERT3 is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get a not seem to get the white grease packet in this size chain but that's ok, I have a lot of these anyway. The chain link is very well made, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
Fits: APRILIA SX50, HONDA NSR80R, KAWASAKI KZ1000 Police, KAWASAKI LeoStar, PEUGEOT Speed Fight 2 WRC, ROYAL ENFIELD Britt 500, ROYAL ENFIELD BritClassic, ROYAL ENFIELD BritClassic Deluxe 535, ROYAL ENFIELD Lightning Custom 535, YAMAHA 125R, APRILIA SR125, APRILIA SR150, APRILIA Mojito Custom 50, BETA EVO 80 JUNIOR, BETA EVO 80 SENIOR, BETA rr 2t 250 enduro, HONDA CRM250, HONDA CRM250R, HONDA CRM50, HONDA CRM80
watchman
For Stock.
It is a standard product and safe.
View detail
Fits: APRILIA SX50, HONDA NSR80R, KAWASAKI KZ1000 Police, KAWASAKI LeoStar, PEUGEOT Speed Fight 2 WRC, ROYAL ENFIELD Britt 500, ROYAL ENFIELD BritClassic, ROYAL ENFIELD BritClassic Deluxe 535, ROYAL ENFIELD Lightning Custom 535, YAMAHA 125R, APRILIA SR125, APRILIA SR150, APRILIA Mojito Custom 50, BETA EVO 80 JUNIOR, BETA EVO 80 SENIOR, BETA rr 2t 250 enduro, HONDA CRM250, HONDA CRM250R, HONDA CRM50, HONDA CRM80
Plug replacement
Regular Plug replacement for CRM. It is a little bit covered. View detail
Oil Filler Cap
Changed to Green Light or Gold. View detail
Yearly update?
I replaced the Front Disc on my 89 MD24.CRM250RK with a new one due to a Brake Overhaul. The original Rotor is still usable, but I replaced it hoping for a slight improvement in touch. The replacement was easy, but the OEM front hub cover could not be installed, so I applied anti-loose agent according to the service manual and tightened at 1kg/cm (98N/m). In the test run, I did not feel any difference in the touch and the braking power, partly because I had not yet gotten accustomed to the pad.
However, the lack of wear would be expected to improve Touch.
View detail