Reviews
No texture, but looks good.
It's pricey and cheap-looking, with some rattling in the locked state, but it looks pretty cool at a glance. View detail
Just right for Helmet
Purchased to protect a high end Helmet that I had to replace.
Although I had always been of the opinion that it should be placed on the ground, I purchased it as a peace of mind fee because it was true that I had some anxiety when I left the house for a certain period of time, such as to go out for a meal.
The length/thickness of the lens is just right for a helmet.
It has a thickness and texture that is not so thick that it could be cut by a nipper if it wanted to.
I haven't tried it because I don't want to get hurt.
I think it is robust enough to be safe compared to a 4φ degree of comfort Wire. (Personal opinion)
The thicker the better, but too much weight and maneuverability will reduce ease of use. Also, there is a risk of damaging the helmet or vehicle body.
Based on this, it is about the upper limit of thickness and flexibility that makes it painless to carry.
I think this spoon-feeding is brilliant.
It is reasonably long, so it can be used through the chin area if it is full face.
Personally, I am concerned about the crushing of the cheek pad when the D-can is passed through the Helmet lock, so this is another point that should not be overlooked.
The rings at both ends are large enough to pass through each other, so the lock at the attachment point can be used to lock the small rings to the large rings.:Even if 2pcs cannot be passed through, they can be locked by using them in a figure 6 configuration as shown in the photo.
This flexibility is good.
Also, the risk of damaging the helmet or vehicle body is low due to the Vinyl coated wire.
In general, this is an easy-to-use Wire for Helmet lock.
I think this is a good price for an exclusive product, ”buy”.
View detail
I thought it would work for home or travel.
The locking part is the heaviest and hardest.
I do feel comfortable with the weight and sturdiness of the product.
I would like to have 2MSize if I wanted to.
I would personally use it for home storage or travel.
I think it is a recommendation.
View detail
Can be used in combination with other locks for extended use!
This product can be used in combination with other locks and can be extended, and the cable is covered with Vinyl to prevent cowl and other wounds from sticking. View detail
Compact
I bought it for the price because the System helmet does not fit under the Seat of PCX150 (KF30).
Even if you don't bite the rubber plate, the small bracket can be used for the firmly.
I am glad I purchased this product because it is Compact and does not interfere with the windows of Brake fluidCylinder.
It is exactly the same thing, but it is DAYTONA for some reason.
View detail
I am satisfied..
I installed it in Handlebar.
Small Chihiro 's Clamp then was too small, I used the for Inch, but this time I got a gap and needed to pinch the Cushion rubber.
Attention is needed for a bar of a different type.
Maintenance is necessary at regular intervals, as is also noted in the notice, sometimes becomes hard during use.
View detail
I am firm
I made a firm purchase to use it for preventing theft such as Back. Helmet is OK if you use it through DRing. It is short to fix Back to Motorcycle. View detail
Not conspicuous
Helmet lock of ZEPHYR 1100 was near the Left Rear suspension and it was hard to use, so I purchased this product.
As usual it was over a Right Mirror for a short time, but I was still worried
I attached it to the Right Side of Handlebar, but it will easily turn around even if you tighten in Yuruyur at your impre street. So I could fix it as Firmly after squeezing in advance prepared Cushion Tape.
It looks as though it looks black, so it is not noticeable.
Afterwards it is said that movement will be bad unless Maintenance is done, so I do not know what the durability is but because the price is cheap.
View detail
Easy to install at low cost
Grom 's Helmet holder is a type that removes Seat, so it is hard to use. So, many of us want to purchase Helmet holder separately, Honda's OEMParts catalog also has Helmet holder. Although it is made by KITACO, it is a bit high with price 3024 yen.
Honda's way of getting a user to buy an Option Helmet holder separately, adding a useless helmet holder to the Motorcycle makes me angry. If you are looking for somewhat cheap things, Design is also a beach, not noticeably attached to Refreshing, and the price is cheap (About half of KITACO) This product was found. When ordering immediately, the item received was made by DAYTONA. DAYTONA thought that there was no mistake, I tried installing immediately.
By the way, there are only cheap commodity, both of LargeSmall two Clip are too large for Grom 's Handlebar. Just like this, it is a good thing, cut the Elastic band, paste it on the Reverse side of the Clip, take it and it will OK. Installation is quite easy, but only Hexagonal Wrench is necessary.
I attached it to the Left Side of Handlebar. It is frosted black, so it fits like an OEM. Looks satisfied. Try adding a helmet to the trial. I will hit Tank, but since it is used when I am parking, there will be no problem.
To multiply Helmet, insert the key and use Quantity : Pair (for Left and Right) It's easy to handle because it only turns 90-degrees to either..
I thought that this was cheap and I did a nice shopping, and when I entered the test running, I got out with a faint sound with Pushing Pushing ___ ___ 0. Because there is play in the part of Hook, it seems that it is producing sound by vibration. Those who are concerned may be good products a little higher.
View detail
It is used for helmet without D can, a little concerned about security side
I bought this Helmet lock as I bought Predator Helmet which is occasionally mentioned in the Net neighborhood of Motorcycle relation.
【What made you decide the purchase?】
Predator Helmet bought in overseas mail order did not have D-can for Helmet holder, because I had anxiety about Security side, I had to buy it because I needed it.
【How was it actually used?】
Even if Predator Helmet, which is larger than the ordinary Helmet by Large, goes along Limit.
Also Vinyl coating is done so it is better not to worry that the Helmet will be scratched.
[Is there anything I was disappointed about?]
When I think that it is disappointing, it is time when I was stolen, I thought it was the thickness of the Out feeling if I could bring up a big Wire cutter.
If we keep Helmet fixed to Motorcycle and leave for a long time 1 pc or more Quantity : I think that it is useless unless you increase 2 pc.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that if there is a thing of Wire which is about the same about Length or a little longer Type and about 2 more rounds, I feel more secure..
【Have you compared items?】
nothing special
[Others]
Although I did not hear much in the past, in recent years I heard that the security has deteriorated due to the inflow of Large in disparity society and foreign foreigners, the spread of NetOakion which can be resolded, and Helmet is stolen successively.
If we reduce the Risk that Helmet is stolen and will not be able to return from the destination, we think that we should defend ourselves using such Wire and Helmet holder.
View detail
Simple appearance and ease of use are good, weak fixing force to Handlebar
【What made you decide the purchase?】
In the past I used a type Helmet holder tightening with the Clamp of the Master cylinder made by KITACO, but for the sake of convenience it looked like an alternative thing because it looked so bad looking, I found and purchased the Helmet holder of Midge which seems to be easy to use in Simple.
【How was it actually used?】
As a Holder application, it is possible to use it normally without being impossible.
However, as described in the Package, it seems that we must regularly lubricate with Spray for the keyhole, and the movement of the key felt a bit awkward from the beginning of purchase.
【Mounting was difficult?】
Installation is easy with the hex of Wrench.
Those who are not used to attaching this hand are HolderBody, Bracket, tools etc. It would be better to curl so as not to hurt the car body by dropping it.
【Please tell me the installation point and hang】
22. I attached it to a 2 mm diameter Handlebar, but the fixing force to Handlebar is weak, Holder will move easily by hand.
That is a problem with that, so we have fixed a thin anti-slip tape on the Bracket on the HolderReverse side.
[Is there anything I was disappointed about?]
The lack of fixing force to the above Handlebar was disappointing.
It is ruined though it is a good helmet holder.
I was seriously considering going to incombustible garbage until I found a thin type anti-slip Tape at Home center.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Anyhow, please fix it to Handlebar.
I think that it is impossible to hang an expensive Helmet with confidence if the Helmet holder itself seems to move up and down with a slight force.
【Have you compared items?】
Size is small Small Helmet holder which is all unified with Black from keyhole to Holder part is this there is nothing compared..
[Others]
I think that if the fixing force to the Handlebar and the durability of the keyhole are managed somehow it will be the best product.
It is true that it is overdoing a bit.
View detail
Sounds noisy
I attached it to the Handlebar, but as I was driving, I was annoyed, so I immediately removed it. It is unknown whether it is manufacturing error or originally, but it seems that there is no problem with the function as a lock. View detail
It is easy to use
This product is installed in the Handlebar Right Side, locked with D camp while holding Helmet on Mirror.
I use Wire when D can not reach.
I think that it will be useful in those who can not use Helmet lock with Side bag or when it is Tandem.
Quantity : Pair (for Left and Right) Usability is good as it can be opened and closed both.
I think that there are no drawbacks especially with subjectivity.
View detail
Convenient.
Previously, I attached the company's Helmet lock to the Handlebar. (I feel that it is inconspicuous. )
It is a good feeling that it is stable when putting Helmet on Mirror, but since I became a situation where Strap did not reach, I purchased it here.
View detail
It is inconspicuous. This is good. I will attach it to other Motorcycle.
It is a good feeling that Matte Black has matched with others. I do not notice it until I can not say it. Point to the key and Quantity : Pair (for Left and Right) The mouth moves to. Also Bolt of installation is secretly hidden by key so even ordinary Bolt is safe. By the way, Harley something like Helmet lock is used once Bolt can not be removed, it is very hard to change the place.
Moreover, when you exchange Bolt, you have to buy a dedicated Bolt. It's Inch, it's a special Pitch Bolt.
It was sent in DAYTONA 's Package. It is safe if it is DAYTONA.
View detail
Since it is hot or there are Helmet form, therefore a time of not being hooked well using a Helmet holder, it is for business then. jaw string's D can -- although it is, one is fixing the tip to the Helmet holder which it let pass from the bot
Since it is hot or there are Helmet form, therefore a time of not being hooked well using a Helmet holder, it is for business then.
jaw string's D can -- although it is,
one is fixing the tip to the Helmet holder which it let pass from the bottom before to the Full face, and was attached to the handle part as it was, since it may be cut the whole jaw string and the Helmet holder may be robbed,Kana in which this one is hard to be stolen also appearance --
View detail
[ -- the Webike Monitor ] -- the Helmet holder of the black Body which is not so exaggerated was looked for. The goods here are not very small conspicuous. inserting the key -- right and left -- since it carries out movable to both -- m
[ -- the Webike Monitor ]
-- the Helmet holder of the black Body which is not so exaggerated was looked for.
The goods here are not very small conspicuous.
inserting the
key -- right and left -- since it carries out movable to both -- m -- understanding intuitively --
-- I am easy -- it is operation.
-- however -- a little -- the plug of a key -- it is related movable and an astringent motion is carried out.
Since
notes have a periodical Maintenance with necessity, they are the point cautions.
I think the comparatively good goods of the price.
View detail
It purchased as a Cable for using it, using together with a Hell lock. the goods themselves are strong -- that's right, since it carries out and the covering itself is solid, there is no fear of a crack being attached not much, but since it was somewhat
It purchased as a Cable for using it, using together with a Hell lock. the goods themselves are strong -- that's right, since it carries out and the covering itself is solid, there is no fear of a crack being attached not much, but since it was somewhat larger than the portion of the ring of a Wire considered, when letting a Cable pass to the metal fittings of a Helmet, it completely leaves -- it comes. If it is a Helmet of a Full face, it may be easy-to-use to a slight degree. View detail
Since the condition of the Helmet holder of a SEROW was bad, it purchased. When attached to the Handle, it was very easy-to-use. When getting down from the Motorcycle until now [ ], it was walking around with the Helmet, but the necessity was al
Since the condition of the Helmet holder of a SEROW was bad, it purchased.
When attached to the
Handle, it was very easy-to-use.
When getting down from the Motorcycle until now [
], it was walking around with the Helmet, but the necessity was also lost now.
I think that it is compact and a Design is also good.
However by an OFF state, I think that the engine performance more than a price has that also dissatisfied ?
just for a moment since it does not escape from a key!
View detail
[ -- the Webike Monitor ] -- my car being poorer than domestic-oriented vehicles, and a Helmet holder for a reverse vehicle, in two right and left, the short Hook has only come out to the Seat rail on the back side of a sheet, and it did not seem to
[ -- the Webike Monitor ]
-- my car being poorer than domestic-oriented vehicles, and a Helmet holder for a reverse vehicle,
in two right and left, the short Hook has only come out to the Seat rail on the back side of a sheet, and it did not seem to use daily at all, but although it thought that there was a crime prevention top problem, the Helmet was constructed in the Mirror and placed on the Tank.
If this Cable can also contain clothing, with the thickness of about about 5 mm, its Crimp of the portion of the ring of both ends is also strong, and can feel easy about it.
Although it is too thick slightly and it is a difficulty to take time in the ring at shortage and a tip also having larger suppleness and letting a Wire pass to the metal fittings of a Helmet, the thick Wire uses, is safe and merely thinks that it is effective on crime prevention.
It ends at a low price and a Cost performance is also the highest rather than preparing the brand-name parts for other vehicles.
View detail