Great tweezers

Love these so far. They are a great build quality that feels sturdy in the hand.Works great and made from metal so it's more environmental and sustainable material. Pleased I avoid buying another plastic tool.definitely recommend View detail

It is intended as an alternative to in-vehicle tools and for emergency use on the road.

The ZX-6R has an on-board tool storage compartment in the back of both the Tandem seat and the optional Single seat cover, but to use it, the storage bracket must be removed with a Hexagonal Wrench. It is very inconvenient though it is appreciated.

Since the servo motor of the exhaust device was removed to replace the external Slip-on Silencer, we decided to use the space to enhance our on-board tools and purchased this Compact with a minimum of tools.

For suspension setting, the Rear rebound damping force cannot be adjusted here, but I don't think this is a place that needs to be changed frequently in terms of usage. I have made a judgment on this.

Front can be used for each adjustment point.

I think it is better to prepare proper tools for daily maintenance, but I think it is better to separate it from emergency use on the road. View detail

Spare parts for Kashimaru-kun

I broke a Pin during Chain cut, so I bought the part. View detail

520Chain Exchange

I purchased this for Chain replacement.
It is easy to understand if you DID watch YouTube before working on it.

hang carefully and accurately. View detail

I cannot believe how easy this tool made the crankshaft installation

About quality and texture - The crankshaft assembly tool from Kitaco is made from a heavy duty steel and with an oxide coated surface finish, the quality from the overall fit and finish is perfect. About the feeling of use - I cannot believe how easy this tool made the crankshaft installation. Simple to use with basic hand tools and sustained no damage to the crankshaft or tool itself, so will able to be used again and again for the future engine builds that I have lined up. Products to buy together - A key product to purchase that will allow for removal of the crankshaft at home is a crankcase splitter tool, it is designed to pull the crankcases apart and can also be used to push the crankshaft out of the crankcase. Difficulty of installation - The installation of the crankshaft assembly tool is a simple task that took 0.5 of an hour to complete. Some mechanical aptitude and the use of basic hand tools is what is required to secure the crankshaft assembly tool between the crankshaft and crankcase. Cost performance and comparison with other products - I find the cost of all the products Kitaco sell to great value when compared to what most other companies sell their products for but this is not the case the crankshaft assembly tool as it is more on par but specific for the Honda Grom and not a universal tool, which is great. About shipping and packaging - With there being no significant cost difference between sea freight and EMS for the crankshaft assembly tool, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - Webike Japan is the first place I look to for all my motorcycle needs. From service parts to performance products and even motorcycle gear and apparel, Webike always seem to satisfy my needs in regards to availability and pricing. View detail

Racer 900 wash for Vehicle

I have a φ10-φ34 and bought it because it was too small for my Racer 900.
You can block it with Tape, but it is not expensive and is useful because it is not expensive and only needs to be inset. View detail

Protect your spark plugs while out riding trails

It would suck if you got stuck in the boonies because of a fouled plug and you're not carrying any spares. This case works perfectly. The most important thing is to protect the spark plugs from impacts that could change the gap or damage the tip.Not sure about larger plugs, but this was absolutely spot on for my bike plugs.It's made of a quality plastic.Really good price. Small and very secure, for longer trips. Especially when going into the local dark continents, where no one else goes. Good travels, safe journeys, and... go prepared. No one else cares, or goes. View detail

A good tool that helps save time

I bought this socket handle again. It takes up very little space in the tool bag. I just put the sockets in my toolbox. It takes up very little space. It is very useful and ergonomic. It is very easy and fast to use.Depending on the job, this can be easier and quicker than getting a ratchet and extension. There is nothing like it in terms of design. Japanese hand tools are unique in terms of design and quality.I'm glad I have it,definitely recommended View detail

Simple form and easy to use

I was looking for a simple and reliable tool like an in-vehicle plug wrench from a well-known tool manufacturer, and I found this product and immediately bought it because of its low price.

The price is a bargain, but the quality is so high that it fits perfectly with the plug diameter, as you would expect from a KTC product.
The rubber inside the wrench gently holds the plug in its mouth so that there is no danger of dropping it when it is removed.

Also, the tool is available in two different thicknesses at both ends:16mm = CPlug and 20.8mm = BPlug, so it can be used with CUB and MONKEY. (CPlug) and 2-stroke VESPA (BPlug) This is more convenient for me as an owner of a
However, since it is a straight type, it may only be used on cars with a large space above the plug hole.

The L-shaped bar is also very easy to use because of its ingenuity in making it possible to use it even for car models that are difficult to get space to turn.
The simple shape makes it easy to pack, so it would be excellent as an in-vehicle or portable tool.

Durability is still unknown, so it was not rated yet. View detail

Is the length of the short method better?

I tried to make a 15-socket holder, but I didn't think about the length of the holder. I didn't think about the length of the holder, because it was about 30cm long, so I couldn't fit it in my tool box. 10-socket holders are available in the Quantity:2pc. I should have bought Set. But
It is definitely better than the Gold genus because it is made of plastic. View detail

Poor mechanics buy toolsRose

9.The 5 tools were added in the Grip set since the number of tools has increased since the Rose purchase. The work is easy Plus No.2 Driver.
Only 1 pc. View detail

Lining Peeled Off Tool, but also useful for peeling off the exterior

The product name is Lining Peeled Off Tool, but it is also useful for removing the exterior.
There are two types of shapes, and the principle of leverage makes it easy to apply force, but it is likely to break if force is applied too much.
It's better to break it before the exterior cracks, though,

PushPins and other difficult-to-remove items can also be removed.

When using the product, cure the contact surface with Curing Tape, etc. before use. View detail

Where Solder is connected, etc.

It can be used for branching connection with a solder, protection of Cable, etc.
It would be better to shrink them with a heat gun, but they are shrinked by lightly frying them with a lighter.
Be careful not to put the flame too close to it or it will melt. View detail

Rubberized to prevent falling off

The Spark plug is held in place by a rubber inside to prevent it from falling out.
Well, I have no problem with on-board tools, but I want to manage Torque, so I bought a Plug socket. View detail

For the do-it-yourself maintenance group, this is a good one to have.

Restore of immovable ESTRELLA.
Final touches, Tappet adjustments.
Oil leak is gone but Engine noise is annoying.
However, I need to prepare Thickness Gauge for Tappet adjustment, so I bought this one.

[What happens if I don't make the Tappet adjustment?
Of course, if the tappet noise is too loud, it will bother you, but if you leave it as it is, the wider the gap, the stronger the impact of the blow, and the tappet clearance will widen more and more, which will cause the starting performance to deteriorate and the motorcycle to gradually go out of tune, so adjustments are necessary. 。

What is a mismatch in Tappet clearance?
When the Valve clearance (Tappet) gap becomes Large, a hammering sound begins to be heard. 。 Sound is emitted when Engine is cold, but disappears when warmed up. 。 In such a case, the gap is large, but as it warms up, the gold expands and the gap becomes small, and the sound disappears.

Symptoms
When I stopped at a traffic light, the car stalled while holding the clutch and dropping the GEAR.
In accordance with the Fat Engine Rotation "Tinkle, tinkle, tinkle." and strange noise.


Procedure 〜For ~ESTRELLA
(1) Unload the Tank from the vehicle body.
↓
(2) Cook must be Off 。 By turning it Off, you can lower the hose without wasting Gasoline dripping out (some Gasoline in the hose will come out immediately after the hose is removed).
↓
(3) ESTRELLA can be adjusted to the upper dead center by removing the Cover and turning this Screw. 。 Top dead center is simply the state where the Piston is at the top.
When adjusting the tappet, the position of the piston must be adjusted to the upper dead center. 。
↓
(4) Remove the Plug so that no compression is applied.
I have to move it with no Engine on it.
↓
5) Front Tappet Cover. 。 It can be adjusted by removing here.
↓
(6) Loosen the lock nut attached to the head first, and when the center screw can be turned, it is OK. 。
At this point, it is normal to move the Tappet by hand and hear a chica-chica sound. 。 If it does not sound kachica-chi, either the upper dead center is not correct or the adjustment is gapped considerably.
↓
(7) Insert the Thickness Gauge into the gap and align it. 。 Strictly speaking, this is the process of adjusting the gap between the Valve and the Arm that is pushing the Valve to the proper value.
↓
Clearance on the exhaust side is 0.17 to 0.22mm 。 If the Gauge is pinched by inserting 0.20mm of Thickness Gauge and closing the Screw at the Center, the Gauge will be pinched, and if the Gauge is moved in that state and it feels a little stuck, it is OK. 。
↓
Clearance on the intake side is 0.10 to 0.15mm 。 The intake side may be a little more difficult to do because it is more intricate in location.
↓
(10) To be sure, make one more rotation of the screw with the upper dead center aligned, and then align it again.

[After adjustment
When I drove it, it no longer stalled and blew up better!

I think a single cylinder can be done by an amateur. View detail

Extremely common products

The Vinyl bag, which was only slightly touched by the residual heat of the exhaust pipe, melted and leaked waste oil when it was tied up with the tie wrap. It would be appreciated if you could change to a Vinyl bag with higher heat resistance.
Into View detail

Chain brush

I continue to use it because it is easy to use and inexpensive. View detail

DL1000 V-STROM250 for initial Oil replacement and Oil Filterfor replacement.

I purchased this for the first Oil replacement and Oil Filterfor replacement of DL1000 V-STROM250.
I was able to replace the Oil Filter without any problems.
The Bolt hole in the middle makes it easy to remove the Oil Filter. View detail

I will never buy from them again.

I used it to disassemble the front fork of a scooter, but the tip broke off immediately. In the end, I used a thousand pieces of the same piece in a quantity of 1,000.:I bought 2pcs and managed to remove the C-ring. View detail

good

I think it is worth buying because it can be used for various types of cars!
It would be nice to have one, especially for a 4MINI, as it will be used more often! View detail