Reviews
Adding to the criteria "OEM" element (e.g. in array, in programming, in programming)
[How is it used?
YZF-R25 (2015 model):December 12, 2015 to April 29, 2017
YZF-R6 (13S):replaced about once every two years from April 29, 2017 to September 26, 2023 to date when I feel like it.
CBR250RR (MC51):Replaced about every year due to tearing from the back.
YZFSeries is used in areas where the wind has little effect but there is no roof; CBR is used in areas where there is a roof but the wind seems to pass through it well.
Was the one you received as per Image?
The product is exactly as shown in the Image. The silver-colored part even seemed to be shiningly slightly.
How was your experience with it?
As it is claimed to be a Cowl mirror, it is possible to hang the Cover completely without folding the Mirror.
The front side is Blue in color and has a wide range, so it has the advantage of being able to instantly determine its direction even in dim light.
The Silver color is Main, so it seems to have less heat in midsummer than the Black Cover.
Even if it is midsummer, it seems to be resistant to heat because it has not melted even if Cover is applied immediately after returning home.
The silver-colored areas are gradually losing their shine, but the water repellency seems to be long-lasting, as rainwater runs off as water droplets even after almost 2 years of use. (WaterproofSpray is used occasionally).
The resin part squeezes the string at the bottom, so that the cover can be quickly and easily applied when the resin part is loosened. However, the string absorbs water well.
Wind affects durability, or the side used for the CBR, which is covered and less affected by rain, often gradually cracks and tears.
When used on the YZFSeries, it has not torn and has lasted long enough to replace it when I feel like it.
The protection performance of the vehicle seems to be strong, including UV rays and rain, as it does not tear. The glossy cowl reflects sunlight well and the headlight does not come in yellowish color, so I think it is protected.
[Points to note]
Because of its shape suitable for cowl mirrors, it can be used without folding the Mirror. However, because the four corners are surrounded by the Mirror, Tank and Top Bridge on the Both Sides, water tends to accumulate when it rains, and the mirrors become dirty from there. There is no flooding.
The plastic parts are so tight that if you try to force them off while squeezing the plastic parts, the cowl or string or plastic parts will probably break.
How did it compare to other products?
I have been using Cover since I bought my first Motorcycle and have never flirted with other products, so comparisons are impossible.
If it is just Image, it seems to be kinder to Motorcycle as it does not seem to hold heat as much as Black Cover.
It seems to be easier to put on and off the Cover than the Type that is squeezed by Rubber.
Although a wide variety of Covers are sold by various manufacturers, this is one of the few products by a manufacturer that also makes Motorcycle Covers. It is neither inexpensive nor expensive and multifunctional, but it is a product that combines a sense of security and price so that it can be said to be the best choice if you have any doubts.
View detail
CB1300SBRearPad installed
This is the second time I have purchased this product. I have used it mainly for running events and Gymkhana, but compared to other companies, it does not cry even when I apply Cost surface and RearBrake frequently, and the BrakeField does not boil up, so I would like to continue purchasing it. View detail
In stock preservation
We buy in stock to be able to respond immediately to any repairs that may come in, and this Manufacturer is a Repeater, which means it is cheaper and will last as long as an OEM Product. View detail
Fits: KAWASAKI GPZ1100, HONDA CB1000 SF, HONDA CB1000R, HONDA CB1100, HONDA CB1300SB, HONDA CB1300SF, HONDA CB400FOUR(Air cooled), HONDA CB400FOUR (water-cooled), HONDA CB400SB, HONDA CB400SF, HONDA CB400SS, HONDA CB750F, HONDA CBR1000 F, HONDA CBR1000RR FIRE BLADE, HONDA CBR1100XX SUPERBLACKBIRD, HONDA CBR250 R MC17, HONDA CBR250 R MC19, HONDA CBR250R (MC41), HONDA CBR250RR, HONDA CBR400R(NC23)
It's nice
Grip feels softer and less vibration. View detail
No problems so far.
[How is it used?
NSR250R (MC21) The original Regulator of the "M" was replaced because it was defective.
I had assumed that OEM parts would be quite expensive, but after purchasing the product, I learned that there was not that much difference in Large.
Was the one you received as per Image?
What has been attached so far (OEM？) There are slight differences between the two, but they are generally the same shape.
Was the installation difficult?
With MC21, I couldn't access directly, so I had to remove the Tail cowl before I could work on it.
If Cowl is removed, access is possible from both SIDE, so it is not that Large strange.
How was your experience with it?
The voltage became unstable while driving, and the power consumption became higher when the headlight was turned on.
I have a voltmeter on the car body, Idling, and the voltage is now stable while driving.
So far the symptoms related to Regulator have been cured, but I am a bit worried because many of the past Impressions I have seen have been ruined after a while.
At least it is working properly for now.
[Included Parts:were they on?
Boltetc. must be prepared separately or use the one that came with the product.
[Was there anything that disappointed you?
I'm happy with it so far.
【Review】
I have just started using it and have had no problems with it.
To be honest, there is not that much price difference between OEM Parts and OEM Parts at the moment, so OEM may be a safer choice.
View detail
![PREMIUM ZONE Oil Filler Cap [M20XP2.5]](https://img.webike-cdn.net/catalogue/images/15651/91885_O01_TS.jpg)
self-satisfaction
One point Accent on Red Motorcycle! View detail
This was the only 14T available.
I installed it on a 2011 CBR1000RR.
I was a little worried because it was made by Driven, a manufacturer I was not familiar with, but I was able to install and use it without any problem at all. I recommend this product to those who are looking for a niche size.
View detail
Fits: HONDA 400X, HONDA CB1100, HONDA CB1100 EX, HONDA CB400F (2013-), HONDA CBR400R, HONDA VTR1000FVTR1000F FIRESTORM, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Can be used with the same etc. performance as OEM!
[How is it used?
New CB1100 Exhaust System from OEM to MORIWAKISlip-on SilencerMegaphone Exhaust.
How was your experience with it?
It was shorter in length than the OEM Gasket, but has not leaked for over a year with no problems.
How did it compare to other products?
I felt more comfortable with OEM, but I didn't know the part number, so I used Other Brand Product. The result was better than OEM because it was cheaper and had the same effect.
[Points to note]
If there is any distortion, it would be better to modify the Exhaust System and fit it in.
▼ I think the Slip-on Silencer is a necessary consumable as Repair Parts.
View detail
Fits: HONDA CB-1, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR600F, HONDA NSR250R, HONDA NSR250R, HONDA RVF400, HONDA VFR400R, HONDA VTR250, HONDA VTR250, HONDA VT250 Spada, HONDA jade, HONDA CBR600F, HONDA foresight, HONDA CBR600F, HONDA CB600, HONDA CB400FOUR (water-cooled), HONDA CBR600F, HONDA VFR750F, HONDA CBR250RR (MC22)
I was thinking OEM.
It was a little cheaper than HondaOEM and I thought it would be the same, so I used it, but it seemed to heat up quite a bit and I was worried, so I replaced it.
After all, it is safer to use HondaOEM Product even if it is a little expensive.
View detail
Fits: HONDA ST1100 A, HONDA XL1000V VARADERO, HONDA HURRICANE, HONDA ST1100, HONDA Shadow slasher750, HONDA SHADOWCustom, HONDA Shadow classical, HONDA CB400 SB, HONDA CB400F, HONDA CB400 SE, HONDA GOLD WINGSE, HONDA GOLD WINGF6B, HONDA GOLD WINGF6C, HONDA GOLD WING, HONDA Integra, HONDA Integra, HONDA Africa Twin, HONDA Integra S, HONDA Africa Twin, HONDA XRV650J
Purchased for 778
Replacement for 67926? Purchased with the following information.
I know you want to organize the part numbers, but a normal search by Motorcycle's name would bring up the higher end Filters, and I thought the method was too stingy.
The quality is made by DAYTONA and I have been using it for about 60,000 km so far while replacing it and I have never had any problems!
Be careful not to mistake the part number for the corresponding car model!
View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
It is quite a nice attachment!
These parts replace the bolt for the Handlebar Clamp and allow the RAMMount to be installed.
I am in this state of attachment (⇒ see photo).
It was quite a challenge, but I like the way it is attached to the handlebar and it does not affect the handlebar easily.
This will be useful for attaching a smartphone or Radar or something.
View detail
Fits: HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD2, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD, HONDA VT750CD
exchange
The PGM was broken, so it was replaced with a new Harness, Battery, and a new set of Harness, Battery, and Regulator.
According to the Parts List, it was 31600-MV4-000, but it seems to have been changed to 31600-MV4-010 here.
View detail
Fits: HONDA FIRE STORM, HONDA NSR250R SE, HONDA X-4, HONDA X-4, HONDA VFR750R RC30, HONDA RS250R, HONDA VFR400R NC30, HONDA RS250R, HONDA RVF750 RC45, HONDA RVF400 NC35, HONDA NSR250R SP, HONDA NSR250R SP, HONDA NSR250R SE, HONDA NSR250R, HONDA NSR250R, HONDA CBR900RR, HONDA NSR250R, HONDA CBR900RR, HONDA NR750 RC40, HONDA CB900HORNET
It works well by putting heat into it.
It will be used on NSR2050R (MC21) and CBR900RR (SC28).
Basically, the impression is that it has good sudden braking from high speeds and good control where it is gripped hard.
On the other hand, the initial braking at the beginning of the grip and the effect around the weak grip were weaker.
However, because of the good controllability, it became easier to penetrate the Corner while leaving the Brake from Straight.
I have the impression that it works well with RADIPON MASTER like Yamaha Brembo.
Rotor is less aggressive than the Ceramic type, but the Pad decreases faster.
The general impression is that the Pad is a lightweight rather than a heavyweight, and that it must be driven on circuits rather than in town to experience its good qualities.
View detail
Fits: DUCATI 1299PANIGALE S, DUCATI 1299PANIGALE R, DUCATI 1299PANIGALE, DUCATI 1199PANIGALE R, DUCATI 1199PANIGALE S, DUCATI MONSTER1200S, DUCATI MONSTER1200, DUCATI MONSTER1100EVO, DUCATI HYPERMOTARD821, DUCATI HYPERMOTARD821 SP, DUCATI MONSTER696, DUCATI MONSTER796, YAMAHA TRICITY125, YAMAHA TRACER900, YAMAHA TMAX530SX, YAMAHA TMAX530DX, YAMAHA MT-09 TRACER, YAMAHA RZ50, YAMAHA TMAX530, YAMAHA R1-Z
oil cap
The genuine oil cap is easy to open and close, but it seems like it could be a good choice in case of an unsuspecting terrorist attack. Furthermore, the aluminum and design are great. It could be a water reservoir. I don't know if it's an outlet or a sealing hole, but it will fly away in the wind. The color is black. I tried to choose it, but it was out of stock, so I went with the green color that was in stock as a last resort in case the delivery would be delayed, but when I saw it in person, I really liked it. It was not a bright green, but a dark and somewhat heavy color. Green color recommended. My car is not in the CL500 category --- -------------------------------------------------- ----- The pure oil cap is easy to open and close, but it can be a good choice for terrorism, but it is also excellent for design and design. I tried to choose to choose, but I didn't have stock, so I was so delivered to the green color with a stock. I liked the real thing. Powered by Google Translator View detail
Fits: DUCATI SCRAMBLER(800), HONDA CB1000R, HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB125R, HONDA CB1300F, HONDA CB150R, HONDA CB250R, HONDA CB400SB, HONDA CB400SS, HONDA CB750, HONDA CRF1000L Africa Twin, HONDA CRF250L, HONDA CRF250RALLY, HONDA CTX700, HONDA DN-01, HONDA GB250, HONDA GROM, HONDA GROM
Essential Items for attaching the Smartphone Holder to the ZX-10R.
Essential Items for attaching the Smartphone Holder to the ZX-10R.
The installation itself is not so difficult, but the Screw where it is attached is special,
It is impossible without a proper Torque wrench.
[Maybe it's just the '24 model, but...]
It also requires a locking agent, so at first glance it looks like it can be popped on, but to a certain extent it is.
Tools and equipment are sometimes necessary.
I've only been using it for a short time, but the RAM Mount system is just as good. Durability is for sale,
It is safe in the knowledge that it will not break that way unless it is defective in the initial stages.
View detail
Fits: DUCATI 1199PANIGALE, DUCATI 1199PANIGALE R, DUCATI 1199PANIGALE S, DUCATI 1299PANIGALE, DUCATI 1299PANIGALE R, DUCATI 1299PANIGALE S, DUCATI 848, DUCATI 848 EVO, DUCATI 899PANIGALE, DUCATI 959PANIGALE, DUCATI DIAVEL, DUCATI HYPERMOTARD796, DUCATI HYPERMOTARD821, DUCATI HYPERMOTARD821 SP, DUCATI MONSTER1100EVO, DUCATI MONSTER1200, DUCATI MONSTER1200S, DUCATI MONSTER696, DUCATI MONSTER796, DUCATI MONSTER821
It is cosy and easy to use.
I have been using this for all Oil Filler Caps recently.
I like the design and the cost performance.
View detail
Fits: HONDA XL600V, HONDA XL600V, HONDA XL600V, HONDA XL600V, HONDA VTR250, HONDA VTR250, HONDA VTR250, HONDA VTR250, HONDA VTR250, HONDA VTR250, HONDA VT750, HONDA VT500FT, HONDA VT500FT, HONDA VT500FT, HONDA VT500, HONDA VT500, HONDA VT500, HONDA VT500, HONDA VT500, HONDA VT500
Genuine Honda Spare Blank Key for XR650L
I had an issue with the ignition barrel and snapped the key in the process. After a lot of pushing and pulling the key decided to snap, my bad. So I did not have to go and buy a totally new set of locks, I had an old set hanging around and decided I would get the lock set cut with a new key, this is where the new blank key comes in.I could have just got some random generic key but as this is an essential part that needs to work every time,I went for the genuine Honda one. The part number was not particualrly hard to find and Webike had these available. Win, win. The price was very reasonable and better than could have sourced locally. There were a few other parts in my order and all were shipped with EMS and arrived in 5 days. All my parts were received in perfect condition. The key even came in a small Honda bag which was a nice touch. The key has a really good and solid feel to it. Although it is a blank, the edges are smoooth as you would expect. I got the key cut and installed my new/old lock set. All works perfectly and now I can get my seat off. Thank you Webike, great job. View detail
Fits: HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA
It's not noticeable, but it's a dress-up!
Little by little, we are doing Small Sana Custom.
This time, we installed this CylinderCap.
Prepare Screwdriver and the replacement is complete in a few minutes.
The subdued gold color gives it a subtle presence.
It is a modest dress-up, but I am satisfied.
MORIWAKI products indeed.
View detail
Fits: YAMAHA tricker, HONDA CBX250, SUZUKI RG400, SUZUKI GSX400, KYMCO RacingKing180Fi, KYMCO Downtown 200i, KAWASAKI GPZ250R, HONDA CB125T, DUCATI MONSTER400, DUCATI 999, DUCATI 916STRADA, APRILIA TUONO1000, YAMAHA YZF-R6, APRILIA SRMAX300, YAMAHA Majesty S, YAMAHA YZF600 Thundercat, YAMAHA ZEAL, YAMAHA YZF-R15, YAMAHA YZF-R3, YAMAHA NMAX
Long-established Manufacturer in Japan
This was my first purchase of the Cowl&nei Kit dual-use Cover, but I was able to use it without any problems. The image of the cover is so inflated that it makes you think you've switched to a Large Motorcycle. Quantity:Pair (for Left and Right) It is designed to be a straight line from Mirror to Seat, with no ventilation function etc. Easy to put on and take off with Center belt1 pcBuckle, very easy and hassle free. Lower part (hem?) The part is tightly squeezed by the tension of the rubber and looks good. I have been using the surface fabric for a while now and so far it has not been stained and has a good thickness and hardness, so I am looking forward to its durability. View detail
Fits: HONDA XR100, HONDA XR100, HONDA XR50, HONDA XR50, YAMAHA FZ-6S, YAMAHA Lanza., YAMAHA Lanza., YAMAHA TZR50R, YAMAHA TZM50R, YAMAHA TT250R Raid, YAMAHA TT250R Raid, YAMAHA TT250R, YAMAHA TT250R, YAMAHA MT-07, YAMAHA MT-09, YAMAHA YZ250, YAMAHA YZ125, YAMAHA XT225 CELLOW WE, YAMAHA XT225 CELLOW, YAMAHA XJ6S
High but improved maintainability
[How is it used?
I'm concerned about rust on the pad pins since we are in a salt-affected area.
Was the one you received as per Image?
Yes
Was the installation difficult?
No
How was your experience with it?
Durability to be determined, Pad slides well.
[Included Parts:were they on?
None
[Was there anything that disappointed you? None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail