Reviews
Control voltage is too high.
After installation, I casually applied a tester to the battery and found that 16V was output!
I thought it was quirky and expensive, so I measured it and found that both Regulator and Battery
Idling (1600 rpm) The control was at 16V at 4000 rpm and 17.5V at 4000 rpm.
This is not usable!
Idling when I put it back in the OEM that I removed it from. (1600 rpm) The voltage was 14.5V at 4,000 rpm and 16V at 4,000 rpm.
Wasted... Worst of all...
View detail
I wasn't expecting it.
I bought this as a rear shock for my old Scooter.
The Machine is Honda's first LEAD80.
Thank you very much
View detail
It's confusing.
When you purchase Slip-on Silencer.
Click here to purchase Gasket." I bought it together with the Full Exhaust System because there was a LINK with it, but it was a part that I would not use unless I was replacing the Full Exhaust System.
I learned from the Instruction Manual for the Exhaust System I received that a joint gasket is required for the Slip-on Silencer for the first time, so this product was a waste of time.
I would like you to put up a LINK to the recommended parts to purchase for the product.
View detail
OEM same etc., inexpensive and good.
It was used for the second Exhaust System removal and installation.
The texture was almost the same as OEM.
Since it is Gasket, the feel is comfortable.
Quantity:1 Set of 2pcs. so it is also cosmetically pleasing.
View detail
OEM same etc.
Quantity:1 Set of 2pcs. to Spare when returning to OEM.
It's good enough
View detail
Grip replacement for LETS4
The LETS4 grips that I have been using for many years have started to hydrolyze and become soggy, so I switched to this product's grips.
The original grips can be easily removed by wiping Parts Cleaner between the handlebar and the grips.
The grip is the same as OEM and easy to use.
View detail
No problem, but...
Coupler is a little bit small and a little bit tight.
At first I thought I had the wrong part number because it didn't fit.
View detail
fitment issues
I was excited to recieve this poduct. There are a few fitment issues with these plastics for my af27 dio. The front piece the 4 bolts on the back side only two line up the other two are so far off would need to enlarge holes to make it work. The top headlight piece does not fit well pops out on the one side and on the middle. The rear pieces seems to fit alittle better but not the best. View detail
Fits: HONDA Giorno, HONDA jorio, HONDA G DASH, HONDA DIO, HONDA SUPER DIO, HONDA LIVE DIO, HONDA SUPER TACT
It didn't fit the GYROX mid-term.
It did not fit GYROX (TD01-17~).
The diameter of the thickest part is too thick and pops out even though it is shaved down a little to put it in.
I made my own Bracket and attached it with Rubber packing to hold it down.
View detail
Product # 450-3021000
It was purchased for the Honda Super Cub to adjust the fuel mixture after installing the whale 75, size 85. Everything is great, I recommend it to everyone to purchase. Purchased for a Honda Super Cub to adjust the fuel mixture after installing kit 75, size 85. Everything is great, I recommend it to everyone for purchase. View detail
Hand Jet
It was purchased for the Honda Monkey to adjust the fuel mixture size 85. Everything worked out great, I recommend it to everyone for purchase. Purchased for a Honda Monkey to adjust the fuel mixture size 85. Everything fits perfectly, I recommend it to everyone to purchase. View detail
Fits: HONDA SUPER DIO SR, HONDA SUPER DIO XR, HONDA SUPER DIO ZX, HONDA LIVE DIO S, HONDA LIVE DIO ST, HONDA LIVE DIO SR, HONDA LIVE DIO ZX
Received
Thank you for your prompt response. View detail
KITACO KITACO Non Fade Brake Shoe
2Quantity as it is used for CANOPY:Set was required.
I just installed and used it, so I don't know how durable it is yet.
Brake's gain has improved.
View detail
KITACO Non Fade Brake Shoe
I just installed and used it, so I don't know how durable it is yet.
Brake's gain has improved.
View detail
Fits: HONDA DIO (2Cycle), HONDA LIVE DIO, HONDA ZOOMER, HONDA SUPER DIO
It's changed.
The suspension that was on was worn out, and the thrust from the bottom was severe. View detail
I was prepared, but ….
The Gasket could not be removed and was reused, although it was inexpensive and ready to go. View detail
Exactly
Size is Exactly on the Groms, Case is always removed so I don't use it in that state, Base is fine left on. The fabric is neither thick nor thin. View detail
Used to attach TM24Carburetor to POCKE
Used to attach MikuniTM24Carburetor to POCKE, KITACO Manifold (410-0012000) However, since the inner diameter of the Manifold side is 22mm, it is necessary to enlarge the inner diameter to 24mm using a Leutor to eliminate the step.
Material:Since it is Rubber, I am not sure how durable it is yet, so I will stock a spare just in case.
View detail
I didn't feel the effect ….
Old Motorcycle about 30 years ago (about 5,000 km on the road) So, I replaced it with a new one for the purpose of refreshment, but as I am insensitive, I did not feel the replacement. The installation is easy because it is screwed on, but it is not difficult to access the Lead Valve because it is necessary to remove various parts, but it is large. View detail
Aging
Used on a HondaTACTA-AF09Courreges TACT85.
I was wondering if there were any parts that would fit since the model is quite old, but I wanted to build it with non-OEM parts, so I bought it.
KM Kikaku Parts has been used on CYGNUS and has been doing well, so we purchased the parts from KM Kikaku, which is famous for its mini bikes, because we thought they would be durable.
There was a little BALI, but it was quickly cleaned up and installed.
I don't know how it feels since it has only been installed for about 100 km, but I think it is large and strong since it is a just fit.
View detail