Reviews
SNIPERSNIPEROil Filler Cap
Perfect for One pointAccent. View detail
Smooth?
When we changed the chain, we increased the number of pins by one and installed a 16T. At first, I was a little worried that I might not have enough power at the start of the ride, but it was not so much of a problem, and on the contrary, I feel that the ride became a little smoother. It may be just my imagination. View detail
Product # 25602
This time we needed grips for the "Suzuki Birdie". Once again, the grips from "Hunter" did not disappoint. Everything fits perfectly, the workmanship and material are top notch as always. I am very glad! View detail
I wanted Cap.
I purchased this product to connect to the Ignition coil in Mukawa and wanted to unify the colors.
Cutter off the adhesive bonding the Cap to the cord, peel off the Cable outer skin of the Mukawa Ignition coil, insert it, and fix it with adhesive, and you are done.
The excess Cable of the product in question is used in place of the Cable attached to the OEMCoil.
This would have been unnecessary if caps in a variety of colors were available, but they are not.
Even if only the cable is replaced, the idling is stabilized and the long-used OEM product is refreshed.
View detail
Absolute safety and reliability
D Type on ADDRESSV125 (with a twist) Banjo bolt is K9 (L3=Last model V125) Using OEM, copper Crash washer is 1.5mm thick.
It works well.
Gyuin! and stop.
(I'm not going to put Brake on it and go through the slushy.)
It is made of one piece of steel and is simple to use. There is no possibility of malfunction or failure due to installation errors. Furthermore, it is less than half the price of other companies' products, so there is no other choice but to buy it.
OEMBanjo bolt is made of steel and is Material in case of a fall:It is absolutely safe because it does not crack like aluminum. The banjo part of this product is 8mm thick and the OEM brake hose is 10mm thick. (hole) The orifice position on the banjo was checked to make sure that the orifice position was aligned with the position of the K7 OEMBER bolt. The K7 OEMBE banjo bolt had the orifice positioned a little higher, with a 1mm crash washer on the bolt head side and a 1.5mm crash washer on the caliper side, and the orifice position was perfectly aligned. The bolt length is also perfectly aligned without any collision.
The Goodridge banjo bolt is made of steel, has a low head and good parenthesis, but when I went to see the actual product, I found that the OEM bolt works harder and faster with a little grip because the orifice diameter is twice as large as the ADDRESSV125 OEMB banjo bolt and the brake fluid volume is larger. The OEM brake hose is stronger and faster than the ADDRESSV125OEMBanjo bolt because it discharges more brake fluid. Furthermore, the orifice diameter of the mesh brake hose was also the same. Of course, the limit of the brake hose is the same for both the OEM brake hose and the mesh brake hose, but you can precisely adjust the brake effect according to your grip, and since the hose is not inflated by the pressure, the brake can be applied to the maximum large limit, which means that the brake effect is better.
FTire is IRC MBR740 DIX-RR with high grip. if the Brake works but the tire does not grip, it will slip. The order is to use high grip tire first, then change Hose and Pad.
Was the installation difficult?
This is a difficult category. I did a lot of research beforehand and measured the length of the ADDRESSV125 OEMHose to be 875mm, and the next setting is 850mm after the 900mm length. 900mm is definitely not pulling on the Hose, although it is a little dubby in the front cowl. We also put it through the OEM Guide and Rubber. This is the most important security component, so take your time and be careful.
How was your experience with it?
The best. Outstanding reliability. Hyper Sintered Pads, but they work so well that I thought they had been replaced by Golden Pads! Hyper Sintered Pads, but they work so well that I think they have been replaced by Golden Pads! (works fast). 。
Golden pad and high grip tires are also available.
[Was there anything that disappointed you?
No. I can't help but think that DAYTONA is a good company! I'm sure you will agree with me.
It doesn't matter if it looks tacky or not. Performance supremacy.
Very nice product, thank you.
View detail
Small gear replacement at an affordable price
I replaced the 14T small gear, which is the same as the original one, without any burden. First of all, I have confidence that it is a Kitaco product, and I expect the product to be durable as well. I purchased and installed the chain and large gear together, and I recommend them because they are satisfactory items at a relatively low price ---------------------------- ------------------------------ It is expected that it is a Kitako product. I bought and installed the chain and the waiting gear together, but I recommend it because it can be satisfied with a relatively low price. Powered by Google Translator View detail
Power cable & elect. module Dev'moto
Bonjour from France Thanks you for quick shipment of my order , i fixed it on ma yam sr 125 in addition of a new electronic module Dev'moto(made in France) with an iriduin plug already than replace the TCI -dead-:( the result is more better ( already too with the new module) cold cranking + little better torque at low rpm, and more i could reduce my idle setting ... so very happy with my purchase ... voilà ! View detail
It's very conspicuous...
Nomal black caps with pinch points are tacky.... View detail
Headlight LED
Installation was easy. It was brighter than I expected. View detail
Smartphone fixed
Power supply and phone are easier to attach than Handlebar. View detail
Not installed yet.
I ordered this for my NSR50 RearBrake CaliperOverhaul. View detail
KITACO Drive sprocket
[About quality and texture] It has good quality that can replace genuine products. [About shipping and packaging] The delivery was very fast, so I was happy to install it quickly. The stapler on the package may be sharp, so be careful when opening it. I will purchase the same product next time. View detail
Fits: KAWASAKI ZRX1200 ZR A7F, KAWASAKI ZRX1200 ZR A8F, KAWASAKI ZRX1200 ZR A8FA, HONDA CB400SB ABSSpec. Model:EBL-NC42, HONDA CB400SB, HONDA CB400SF ABSSpec. Model:EBL-NC42, HONDA CB400SF, HONDA CREA SCOOPY Model:JBH-AF55, HONDA CREA SCOOPY i Model:BA-AF55, HONDA DIO4st CESTA Model:JBH-AF68, HONDA DIO4st, HONDA FORESIGHT, HONDA GYRO X Model:JBH-TD02, HONDA GYROCANOPY Model:JBH-TA03, HONDA HORNET250, HONDA LEAD100 Model:EBJ-JF19, HONDA MAGNA50, HONDA PS250, HONDA SHADOW400 Model:BC-NC34, HONDA SPACY125
Reliability Large Stanley
Replacement of Meter lighting and Pilot bulb for VTR1000F.
The VTR was under total disassembly and was replaced.
I thought about OEM Product, but the price is too expensive for 9 pieces!
Quantities at Reliable Stanley:I bought 1 Set of 10pcs. because it was cheap! 。 No complaints and peace of mind.
View detail
Rust-resistant Material from OEM:Replace with Stainless Steel!
OEM is prone to rust, so we replaced it with this product.
Cap is also included.
Material:I thought about Titanium, but it's too expensive Material:Stainless Steel
Quantity because Front is Double disk.:Buy 3 for 1 Set for 1 Vehicle.
The OEM cap can be removed with a slotted screwdriver.
This is very hard to loosen and almost nappy.
The attached Cap is a Hexagonal Wrench for peace of mind.
View detail
Used for Rear
Touch Yoshinshi, better than Junsei. View detail
OEM Equivalent Product, cheaper than OEM
Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.
Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem.
View detail
Fits: Others , YAMAHA YB50, YAMAHA YB-1, YAMAHA TW225E, YAMAHA MATE90 T90D BC-UB02J, YAMAHA JOG Poche BB-SA08J, YAMAHA GRANDAXIS , YAMAHA GEAR N JBH-UA06J, SUZUKI DR-Z400 SM BC-SK44A, SUZUKI DR-Z400 S BC-SK43A, HONDA XR50 MOTARD, HONDA XR100MOTARD
This is my first product and I am satisfied.
This is my first purchase and I am satisfied with the low price.
If it lasts about 5 years, I will be Large satisfied.
View detail
good choice
I bought it after seeing a review that you often replace it with a set with Takegawa reinforced coil. I bought any color because it was hidden in a cowl, and I connected the ngk power cable with the Takegawa reinforced coil and installed it. I had to cut the length and install it, but I thought there would be some loss, so I just connected it. It starts up well and I think it's effective in output. Thank you. View detail
large-volume saving
I found this product when I was looking for a good helmet holder for my motorcycle.
Now I can avoid Helmet from theft and other dangers. I like this product very much.
View detail
Mirror arrived cracked.
The Mirror arrived with a crack.
I didn't return it because I noticed it after I installed one of them.
The box is in the worst possible sticky condition.
I think Design is the best. For a properly managed operation.
I would like it mailed to me.
View detail