I can work on it myself, but it's more difficult.

Link Plate was replaced while supporting the car body with Panda Jack using only Side Stand.

Both foot tongs are now attached up to the ball of the big toe and feel more secure.
Since the rear was lowered, the front fork also protruded 1.4 cm. View detail

Since it is a Circuit premise

Since we are running a holiday Circuit.
It's a hassle to remove Mirror from Cowl mount every time I do so.
For Handlebar Mounting

I bought this to fill the hole in the OEMMirror that I removed.
It's cheap and highly textured.

Large I'm satisfied. View detail

A necessity for maintenance

It is a must-have if you want to keep your Motorcycle for a long time. It is expensive, but it contains a lot of necessary information and is indispensable if you want to keep your Motorcycle large. View detail

It doesn't fit the '23 model.

It doesn't fit the '23 model.
The bottom came on, but the top doesn't fit the Size. View detail

Cospa best

[How is it used?
Helmet hung on Mirror and locked.

Was the one you received as per Image?
Street Image

Was the installation difficult?
In my case, it was a little troublesome because I had to remove the brake lever to install it, but it's easy to install if it's in an easy-to-mount location.

How was your experience with it?
Hang your helmet on Mirror for peace of mind when you leave your motorcycle

[Included Parts:were they on?
No

[Was there anything that disappointed you?
nothing special


With or without Instruction Manual
As an anti-theft measure, the mounting screw is hexagonal, so it can be easily removed with a tool. View detail

Replaced the company's XS319

We were looking for a replacement for the company's XS319 Fastener, which we have been using for several years, due to damage to the Fastener.

Main compartment holds a smartphone (Pixel7pro), a bifold Wallet, an electronic Cigarette in a Case, and Toilet paper instead of Pocket tissue

With the XS319, I had difficulty handling the Cable when charging my phone, but this is not a problem with this product!

The Pixel7pro does not fit into the smartphone storage pocket on the back of the lid because it is not wide enough.
I think the width of Xperia1II used for Navigation is the limit (although it is slightly long). View detail

I feel like I have more Control.

Inner rotor is made of material.:The design is close to OEM, so I don't feel any discomfort after the replacement. The durability (life span) is yet to be determined.
This is just my subjective opinion, but so far I can't find anything wrong with it. I wish the price was a little lower, but I think that is too much to ask for.... View detail

tw200

[How is it used?
Touring
Was the one you received as per Image?
yes
How was your experience with it?
good
[Points to note]
None
How did it compare to other products?
good
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer View detail

fall

If I put it on Normal seat, I think it will be a little forward and downward.
My Seat has no problem because I have removed the anchor, so the Seat is like a crescent moon, and the footing is even better. View detail

The variety was small at first.

I bought this product because I really disliked the NORMAL, mossy Fender. The length and width of the Fender was designed to be Refreshing for the two types of Fenders. View detail

DAYTONA Grove

As the name "Vintage Line" suggests, it looks good. Perhaps it is because of the goatskin leather, but it feels a little stiff, but it may become a just fit as you use it. View detail

Purchased to install a BOX.

Installation is easy if you follow the instruction manual, and the helmet holder is also included. View detail

Large for commuting and touring

Looks well designed, well made, and works great for carrying souvenirs on a touring trip or a large bag on a commute to work. View detail

You should pay attention to them from time to time.

Kick start, synonymous with SR400.
The Kick Arm that I have been using for many years still seems to work, but I feel fatigue (Gold fatigue), and if it breaks in the future, I will no longer be able to apply Engine, so I renewed it.

Kick start
‥To start Motorcycle and other Engines using Kick starter.

What is Motorcycle's Kick starter? ]
The electricity from the battery is used to rotate the Cell Motor, and the engine is started by the power of the Cell Motor. Cell start In contrast, the Rider's own kicking force is used to start the Engine. Kick start." is 。

The benefits of Kick start.
No burden on the battery.
Cell start motorcycles use electricity from the battery when starting, but kick start motorcycles do not require electricity when starting. Therefore, the battery is not burdened, and battery buildup can be suppressed. In addition, even if the battery does run up, the Kick start motorcycle can start the engine manually, which can be helpful in an emergency.

However, if the engine displacement volume is a CUB or something like that, there is also a demerit for Kick start.
[Demerit]
If the force to step down on the Kick pedal at the start is insufficient, not only does the Kick start fail, but the Kick pedal may jump up in the opposite direction with great force. The so-called Ketin." Ya Kickback." This phenomenon is called "ketchin". When kettling occurs, some Risks are hit hard on the shin or other parts of the body by the Kick pedal that has bounced up, causing them to faint in agony.

Ketching Prevention
There are two ways to prevent kettling:using Decompression or not using Decompression.
． How to use Decompression."
The KICK pedal is then lowered vigorously and the engine is applied.

． How to do it without Decompression.
After returning the Kick pedal completely to the top, step down the Kick pedal to the bottom again to start the engine. 。 This is the basic way to hang an Engine using Kick starter.

Kick pedal and Kick Arm.
There are some precautions to be taken when installing the product.

This is the relationship with the Pedal position.
If you are replacing the footpeg with an external footpeg, the Arm itself has less clearance, so there will be interference→at that time, please return to the OEM footpeg.
The OEM footpeg is too large and interferes with the exhaust system. →Kick Arm is OEM.

Replacement is not difficult, since all you have to do is remove the bolt attached to the base of the Kick Arm and replace it.
However, the place where the Arm fits is geared, so be sure to insert it properly aligned with the gears. View detail

Wouldn't this be the perfect maintenanceSTAND for Middle motorcycle!

I am satisfied with the stability of the vehicle when using the rear stand, the lightness when lifting up, and the price. I was thinking of replacing the tires by myself in the future, and I am also hoping to expand the range of maintenance of other parts. (The Z650RS weighs 188kg *Rear Carrier would be better) It only requires a little weight by hand. It is very convenient because I used to do one side lift up with a piece of wood.

Comparisons were made with Company S, Company A, and Company J. As a result, we decided on DAYTONA. As the reason for the selection, I considered that the structure of the most load-bearing part is Square Type, which seems to be sturdy, and that it is superior in terms of comparative cost. Also, the fact that the product introduction image is of RS was a deciding factor. The other 3 companies are all sold separately, and S and A are a little cheaper than DAYTONA, but there were some comments that the stability of the frame is not so good. I have not actually used them, so I am not sure.

The Stand Hook holder is specified to have a diameter of 14 to 18mm. If the diameter is larger than this, it will not fit in the attachment. Also, it takes a little getting used to inserting the Attachment.
The only drawback is that the latch of the U-shaped attachment is too thin and I am not sure if it is durable. I am not sure if it is durable or not. I don't know because I haven't used it yet. However, spare parts are available, so there is no need to worry. (This is not a problem for those who can weld.)

J company claimed that the handlebar should be set to "Left" and "Up" when the brake is "STAND-UP", while DAYTONA company claimed that the handlebar should be set to "Straight". I am not sure of the difference, but I found that the fixation of the hook of the front brake at the time of OthersLift up was the same in all companies. I hope this is of some help. View detail

Used for Tank on Ninja1000sx

[How is it used?
The tank of the Ninja 1000sx is wide, so when touring long distances, the sitting position is inevitably shifted to the front. When I was riding Z650ABS, I used the same manufacturer's standard (black), but I was concerned about the floating of the glue, so I changed to SILICON this time.

Was the one you received as per Image?
Color is Color:It is so close to Gray that when attached to Black Painting, it looks like it is floating. It is not so bad once you get used to it, but I would have preferred a stronger black look.

How was your experience with it?
Functionality is fine. It has a firm knee grip.

[Points to note]
The location of the paste is unknown and must be confirmed on the ManufacturerHP.

How did it compare to other products?
I feel that the texture is not as good as the company's Standard, but it is supple and does not seem to peel easily.

Requests, etc. to Manufacturer
I noticed a lot of White paper dust on the product when I opened the product. Perhaps dust from clothes will also be a concern in the future. View detail

For Day Trip Touring

[How is it used?
I purchased this bag to hold my baggage for a day touring when I took delivery of my Ninja 1000sx.

Was the one you received as per Image?
The Large size and texture were exactly as shown in the Image.

How was your experience with it?
It is about 1/3 capacity with Rain Suit, Touring net, simple tools and small things.
It can be expanded with a fastener, so there is no problem when storing souvenirs, shirts, etc.
The top lid area is glossy Black, so abrasions will be a concern in the future.

[Points to note]
KBelt is convenient, but I am concerned that it will gradually shift forward when driving.

How did it compare to other products?
I used to use Single side bag for my hand luggage, so I have to be careful when I straddle it when I ride.
The drawback is that it is not easy to use, but I like the simple look of the product.

[Installation hang].
The center belt for attaching the KBelt must be tightened firmly when driving.
Note that it will shift forward. View detail

Replaced with a reliable manufacturer's product for future Motorcycle tinkering.

[How is it used?
I used to use a tool sold at Home center, but I was licking the Nut and so on.
We purchased this product as a reliable manufacturer's product.

Was the one you received as per Image?
Matte texture, Laser marking and was as per Image.

How was your experience with it?
The dimensional accuracy is also no problem at all, and it is good to fit Snap to Nut.
Matte texture also fits well in the hand.

How did it compare to other products?
It is a world of difference from the inexpensive tools sold at Home center. A little more.
I regret not buying it earlier.

Requests, etc. to Manufacturer
When the tool box is stored upright, it is unstable because of the protruding hinges,
I would like to see a structure that does not stick out. View detail

Purchased for my 3rd grade Small School son.

Was the one you received as per Image?
Coloring was as per Image.

[How did you feel about the Fit?
When worn by a Small School 3rd grader (135cm tall, slender), the sleeves and body length were too long, though,
I think they can be worn for many years even after some growth.

How was your experience with it?
I have purchased ANSWER Jersey before, but it frayed while I was using it.
It was coming out. We hope that will not be the case this time.

[Was there anything that disappointed you?
No problem except that the Size is Large.

How did it compare to other products?
I expect that the sewing and texture is better than FOX's Jersey, so it will not deteriorate over time. View detail

Good texture

[How is it used?
Purchased at the same time as the 65-piece AutoMechanic set from the same manufacturer.

Was the one you received as per Image?
The Matte texture is pleasant to the touch and the Laser marking is very clear.

How was your experience with it?
There is no dimensional error and it fits Snap and Nut so it is safe to use. View detail