Reviews
cb400sb installation
However, the mounting hardware screws were too small, and since Cowletc. was worked on as it was, I had a hard time installing the screws.
In the end, we compromised and fixed the top with Tie Wrap.
I have toured about 200 km after installation and have had no problems so far without any unusual noises.
I went with Black Plating so it's not as noticeable, but so far I'm happy with it.
View detail
I am satisfied
Buy Black Plating.
There was no indication of fitment on the '20 mt09, but I was able to install it normally.
Simple is good.
I would have been happy if the price was a little lower.
But I am satisfied with the results.
View detail
Fits: KAWASAKI NINJA1000 (Z1000SX), KAWASAKI Z1000 (water-cooled), KAWASAKI Z800, KAWASAKI VERSYS1000
Easy
I think it's an easy to install part that will give you a custom look. View detail
It's nice to see a whole new look!
Very cool.
If only the price was a little lower... (^^;
View detail
Radiator core guard
I think it looks great.
The bolt nut for installation is small and short.
It was a little Large strange for me, clumsy.
View detail
cool
It looks good, and above all, it's practical. View detail
Fits: KAWASAKI Ninja400, KAWASAKI Ninja250, KAWASAKI ELIMINATOR SE, KAWASAKI ELIMINATOR
Fits a 2020 NINJA2 Helmet 50R
2020 NINJA2 Helmet50R (EX250P) attached to the
I was lost in the choice because it came out from various manufacturers, but
I liked the design and bought it.
I think all of Trickster's quality is excellent.
To install, simply attach the included Clip nut and secure with the Bolt.
It's easy (The real work is 10-20 minutes)
The Instruction Manual says to remove the Cowl.
It's just hard to install, but it was Large sturdy without removing it.
View detail
I installed it on my ZrX1200 DAEG.
Any Manufacturer is similar, but since the Engine slider was a Trickster, I went with the same Manufacturer.
I was worried about Black, but I thought Silver would have a better presence, so I decided on Silver.
View detail
I installed it on my ZrX1200 DAEG.
I installed it to protect the Radiator. View detail
Fits: KAWASAKI Z1000 (water-cooled), KAWASAKI Z800, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI VERSYS1000
Used on my 2019 Ninja 1000.
Cowl can be installed without removing it.
Because the logo of Trickster is small, it is almost invisible.
The Rubber that came with it flew away while I was driving...
The performance is the same among all manufacturers, so it is good to choose by design.
View detail
I wanted something Black-ish.
Because Logo wanted Small and Black. View detail
I wish I'd put it on sooner
[How is it used?
It is the Parts which had been anxious for a long time from before, but it begins to be anxious and finally buys it because the mark which Small stone hit on Radiator was made several recently.
Was the one you received as per Image?
I chose the Black Plating one to match my body color.
Was the installation difficult?
I took my time and completed the installation in less than 30 minutes. It was not difficult to install.
How was your experience with it?
I am going to check the effect by long distance touring.
[Included Parts:were they on?
It was on without a problem.
[Was there anything that disappointed you?
Nothing special so far.
Other items that would be helpful
Deciding Factors for Purchase/Included Parts:Presence or non-existence of Included Parts/Points to Note/Opinions and Requests to the Manufacturer
A few more Color variations would be nice.
If you're considering buying one, I'd recommend installing it sooner rather than later before Radiator gets more scratches.
View detail
It's highly effective because it's where you see the Pad.
The Radiator is the most visible part of the bike, so replacing the rusty OEM will change the impression and make the whole bike look better. After 4 years of use, it still has a bit of a shine to it as you can see in the pictures. The design of the Landmark is understated and unobtrusive. The design of the mesh is also good, with 3 sections for parenthesis. View detail
Fits: KAWASAKI Ninja H2R, KAWASAKI Ninja H2, KAWASAKI Ninja H2 SX, KAWASAKI Z H2, KAWASAKI Ninja H2 SX +
PetitCustom
It is a high quality Plating.
Because I chose Black, there is not much change in appearance, but I feel that the effect of preventing damage by stepping stones and beetles is Large.
This is a great product to buy.
View detail
Reliable Manufacturer
I am satisfied with the quality and design of this product because it is a reliable manufacturer. View detail
Light weight protection
Guard looks nice and is very well made. Installation is straight forward and the guard is light weight and does not effect cooling - there's really no excuse not to be using one. View detail
Fits: KAWASAKI Z1000 (water-cooled), KAWASAKI Z800, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI VERSYS1000
Nice product.
Fitting is perfect and Parenthesis is a great product. The BirdstaLogo in the corner is nice too! Installation can be done without removing the Cowl! (It's small and hard to do though) After that, you just need to tighten the bracket part of the lower center with the bolt for Radiator. If you do it well, it will take about 10 minutes. The appearance and practicality are high and Recommendation. If the price was a little cheaper, I wouldn't have to say anything else; View detail
ZrX1200 DAEGRadiator core guard
Protective, Style, I like it! View detail
Does it look good in this one?
I'm not sure what to make of it, but I think it's a great idea. View detail
High quality, highly satisfactory product.
[How is it used?
Since I bought the GPZ900R, it didn't have the OEM Core guard on it.
The Radiator Guard is very important to me, so I installed it this time.
Was the one you received as per Image?
It's very textured and netted? The product is also fine and clean.
The accessories, Screw and Washer, also came with a good one.
Was the installation difficult?
If you tighten the 4 screws to an even surface, it was not difficult.
How was your experience with it?
No problems with Guard performance.
[Included Parts:were they on?
Screw, Washer and collar are included.
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
It didn't come with OEMGuard, so I put a tap in the screw hole first as a precaution.
The rest of the time I applied Molybdenum grease to the Screw to prevent biting.
View detail