At least a necessity if you're going to run Circuit.

Circuit runners have generally pointed out the softness of the Rear, and I agree with them. I bought this product to solve this weak point because I can't change the direction of the rear end when I am turning and I spend a lot of time lying on the ground. I bought this product to solve the weak point of the RACING Link Plate. The initial entry of the car was changed from a squishy feeling to a gushy feeling, and there was no problem with the WindingLevel. The BFRC is fundamentally soft, so there is still a sense of over-movement. I will check if it will hold up or not at the next run. View detail

I put it on to keep the bugs away.

With OEMScreen, the insects hit my neck, so I wanted a slightly largerScreen and chose VS-14.
The objective was successfully achieved and the insects no longer collided with the neck.

It came with a warning to do the Cover when parking in direct sunlight, but honestly, it's a hassle and I'm going to try using it without it until I have a problem.
Is there a real problem or not...? View detail

No instruction manual included

There is no instruction manual. The collar and bolt are confusing, or rather, wrong. The "right side, left side" in the product description photo is "right side, left side" from front to back. The 150mm bolt and 68mm total collar are installed on the left side of the vehicle. The 115mm bolt and 33mm total bolt are on the right side of the vehicle. The tightening torque is 35 ft.lb. It was able to be installed properly on the American specification 451cc Eliminator. There is no instructions come with it. 150mm bolt and 68mm (55mm + 13mm) collar are for the left side. 115mm bolt and 33mm (20mm + 13mm) collar are for the right side. Tightening torque is 35 ft.lb. They fit Eliminator 450 and 500 too. Enjoy! View detail

The Connector part is Compact, but the Body box is in the way.

As a result of changing Navigation from 5-inches to 7Inch, when connecting Navigation power to the USBConnector on the BOLT Shoulder Bag
It became difficult to do, so I thought it would be a good opportunity to replace it with this product, which is 2.4A compatible.
As mentioned in the Title, the Connector is compact and unobtrusive, but the Body (transformer from 12V to 5V?) is not. However, the Body (transformer from 12V to 5V?) is
I was worried about the mounting position because it is bulky.
Finally, it is fixed with Double-sided Tape on the Front side of the Top Bridge, which is hidden by the Bullet Cowl.
Red wiring is very noticeable as it is, so the Bullet Terminal is cut out and soldered on.
Spiral Tube and Wiring Cover were used to prevent the Red color from being seen.

The Connectors placed on the Handlebar are Compact and unobtrusive, so they look good when not in use. View detail

Good but too expensive

Brake masterTank on the Front. [Color] I made it Smoke and so did Rear. [Color] I bought it to make Smoke.
The original bracket to prevent the cap from falling off has a gap between the top claw and the gap, so I bent the claw part down with pliers and attached it for the time being. It is ugly, so I'm going to keep it until I buy a dedicated one.
The appearance is less noticeable. [Color] I am satisfied with Smoke because there is no worry about yellowing, but I think it is too expensive. View detail

Step up from SteelScrew!

[How is it used?
Screw was replaced with external Fender, so Screw was changed from Steel to Material:Replaced with Stainless Steel.

Was the one you received as per Image?
Quality is as good as the Image.

Was the installation difficult?
Installation is easy as the SteelScrew is simply replaced.

How was your experience with it?
Fender is often exposed to moisture, so the replacement was made in consideration of durability, but it can be used without worrying about rust, so it is a sense of security.

[Included Parts:were they on?
No other than Screw.

[Was there anything that disappointed you?
The NORMAL Screw is slightly rounded, but this is a dish Screw, so the shape is slightly different.

▼I'm afraid of biting, but I think it is better than Steel rusting. View detail

Compare with Yamaha Brembo

I was not dissatisfied with the performance of the Yamaha Brembo on the YZF-R7, but there was no lever available to install the REMOTE CONTROLLER, so I had no choice.
Installation, but requires Bullet Terminal processing and Nipple modification on Switch.
Since OEMWiring is a Connector, it is cut and converted to Bullet Terminal, and the RCS side is also cut and shortened.
The Nipple seemed to be able to go as it was, but the Hose needed to be bent 90° and it was too tight, so I changed it to Straight.

The nipple diameter of the RCS is 7mm, but the OEMTank is 8mm, and the RSC side is governed by the 8mmHose, so the 7mm is forcibly installed.
If you are particular, you should buy a 7mm Tank.

The Yamaha Brembo has a banjo on the side, so I used an offset adapter, but the RCS can go without it.
The Chinese $3,000 REMOTE CONTROLLER came on with no problem. The REMOTE CONTROLLER is easier to adjust even if it is not Race.

There is almost no difference in structure between the 16mm Radial Yamaha Brembo and the 17mm Radial RCS, so I don't feel any difference in performance, although the price is about twice as much.

I chose RCS for the REMOTE CONTROLLER, otherwise Yamaha Brembo would have been sufficient. View detail

great seat cover

seat cover fit great and loops over each end of seat for easy installation. No matter how much stretching and how many staples I used, there's a couple wrinkles.The color looks good, but doesn't match OEM. It's a little darker.Lots of grip ! It took a couple days at the to get used to it. Night and day difference from stock.Use 6-8mm staples when you install or else it doesn't stick View detail

Quality good

Side mirror is good quality, matches the look of my bike. However require to order 2 unit. Each order is only 1 side mirror. Hence, i am required to order 1 more side mirror. View detail

Price difference several times. Dozens of times more durable.

[How is it used?
? Continuous use from December 12, 2015 to as of April 13, 2024
100% outdoor use (no roof, with Motorcycle Cover)
Vehicles used:YZF-R25, YZF-R6

How was your experience with it?
The lock is as heavy as it looks, sturdy and secure.
Compared to YAMAHA's Steel links, the durability of the Sleeve is much higher.
I feel that the durability is improved because the sleeve is strong and the chain, which is the body part of the lock, is not exposed.
The rubber part of the product is in a bad shape after more than 8 years of use, but this does not bother us because the rubber accounts for only a small percentage of the product.
It feels like a pure chain covered with a sleeve, and while it can be moved freely enough to aim at the ground right next to where it was lifted, if you are not careful, it will unintentionally come into contact with the Wheel when you put it through it.
While it is heavy and secure, I am concerned about the load on the Spoke section, even though I know that it is better to float the Chain lock for security purposes.
Although the price is higher than the typical chain locks and locks sold at home centers, we would like to believe that the thickness and sturdiness of the locks are also higher, so the priority of being targeted is likely to be lower.

[Points to note]
I think there was a sentence like "easy to carry", but maybe something is wrong.
When loaded on a human being, it is so heavy that his shoulders and back might be destroyed in a second.
When loaded on the Motorcycle side, it is different from a chain lock like YAMAHA or GOJIRA, whose shape is fixed to some extent, and it is likely to move freely, so that the weight is usually on the One Side.

How did it compare to other products?
Y's Gear YL-02 Steel links lock (https://www.webike.net/sd/24118556/)
The Y's Gear is the same chain lock, but unlike this product, it does not bend freely, and it is easier to avoid spikes when putting it through the wheel.
The security of the key to open the door is better with Wave Key's Y's Gear.
The large size of the key to open the lock is smaller than the small size of this product, making it easier to carry.


The Sleeve has not so far experienced any powder clinging to the vehicle due to the raggedness of the Sleeve, and it certainly has the heft, security, and durability for the price. I'd like to use it for a little more peace of mind"than the average. I can recommend this product to such people. View detail

Highly Control

OEM comparison,
Braking power obviously changes.
Touch on Brake lever is surprisingly Mild.
Wear and tear is a little fast.
Aggressiveness of disc is normal. disc replaced at 60,000 km.

The Red Pad is almost identical to the OEM and ends up being about half as durable as the OEM, so the Golden Pad is better as a result.

Braking power should be the first priority because it is more problematic not to stop at a dangerous SCENE.
If you want to replace it at a store, you will have to pay a labor charge. If you buy a Red Pad, which has only about half the life span of a Golden Pad, because it is cheaper, the resulting two-time labor charge will be the same as for a Golden Pad.

In conclusion, Golden Pad has high braking power and good cost performance. View detail

easy to install

At first glance, this is a common and reasonably priced Fog Lamp, but there is one very good point! It has mounting hardware that can be easily attached to the Mirror Hall section! The wiring is short and needs to be extended. "Pon attachment" It's great to be able to do that! The brightness is perfect for an auxiliary light! This product is a Recommendation! View detail

Works like a skid plate should

Installation will require only 5mm bolt. Color match is wonderful for bike. Immediately took this to a local trail to test it out and managed to slam it on some rocks. Held up great, took a bit of damage but that's what it's for! Its tough but it's still plastic so I'm sure it has its limits.something to protect the finish on the frame and keep the mud off the motor.Little to no gaps, excellent coverage of major components.You will need to remove this skid plate when you change your oil.But if you are a little lazy about your oil changes, this may not be for you.This is the perfect solution and was reasonably priced. View detail

I replaced the OEM 10 degrees with this 6 degrees.

When the handlebar is turned all the way to the left, the clutch wire is too tight and delicate. I think it does not interfere with driving, but I am not worried about continuing to use it in this condition. I am worried about continuing to use it in this condition, so I have ordered a special order for a slightly longer wire. It's a hassle! I would like the position to be a little more like a rider's position for city driving. It is now as easy to ride as a CBR600RR. View detail

Buy for Maintenance

The scale is colored for easy understanding.
It is used infrequently, but it is used for Large. View detail

Small size is the reason for rust resistanceMaterial:Stainless Steel Screw!

[How is it used?
Replaced the brake hose guide with an external aluminum guide.:Replaced with Stainless Steel.

Was the one you received as per Image?
It is as accurate and clean as the Image.

Was the installation difficult?
Easy installation by simply replacing it.

How was your experience with it?
It can be used without worrying about Rust.

[Included Parts:were they on?
Screw only, nothing else is included.

[Was there anything that disappointed you?
Not particularly

▼Quantity since wdisc.:Pair (for Left and Right) Four bottles are required in the following table. View detail

I got a different impression than I expected.

I bought it because when I went to Hokkaido Touring, I found a lot of insects stuck in Radiator.
It's quite expensive and I've been slow to put it on since it's winter and the bugs are gone.
When I put it on, the Core was not as visible as I thought it would be, which is good because it gave a different impression.
Design is a matter of taste and I think I am just fine.
You have to run it in the summer to see if bugs get caught in it. View detail

Fun to run.

I have ridden various motorcycles but this is the first time I have installed Rear Sets.
The silver color we chose also has a dress-up effect.
I thought it would be more cramped, but it was not so much and I got used to it quickly.
The Shift and Brake controls feel good and run comfortably.
Very satisfied overall! View detail

RokudaboPlug replacement

[How is it used?
Purchased with Plug as it is needed to replace Plug in CBR600RR PC40.

Was the one you received as per Image?
The quality of the plug wrench is good and the magnet in the plug wrench makes it easy to catch the plug.

How was your experience with it?
As a plug wrench, it does its job well and is highly rated for its texture.
However, since this was my first time replacing a 4-cylinder plug, I struggled with replacing #2 and #3 and eventually gave up and asked Motorcycle shop to do it for me.
We were told that a less thicker plug wrench would be more suitable.
I don't know if I will have to come back to it in the future, but it was good as a Plug wrenchSingle Body.

[Points to note]

How did it compare to other products?

Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer View detail

Oil change essentials

[How is it used?
PCX125 JF56
Purchased for oilfor replacement of CBR600RR PC40.
I was looking for something with a small number of pieces to go home on the Net, and since it was a DAYTONA product, I bought it.

How was your experience with it?
It is like a normal Washer.
I used it when I changed the oil and the fit with the drain bolt was perfect.
After replacing the oil, I have been able to use it without any problems, including no leaks.
I will purchase again next time.
How did it compare to other products?

[Points to note]

Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer View detail