- Home
- Product reviews
- Motorcycle Parts
- Bodyworks
- Rim Sticker / Rim Stripe
- The important thing is the last Dryer.... (MDF: Rim Stripe 10M)
【MDF】Rim Stripe 10M Review
The important thing is the last Dryer.
I'm getting bored with the pure black Rebel and am slowly adding color.
I was going to use White for the Rim sticker, but I thought it would be better to use the same color as Honda's Emblem, which is a bit raw and silvery, so I chose Light gray, which seems to be the closest color on the Catalogue.
The actual color that I received was a little darker Titanium-like color (but not Gun meta) and I thought it was darker than I expected, but when I put it on, it fit well.
The Rim width of the OEMWheel of REBEL250 is 14mm, so I chose 10mm which seems to be the thickest among the compatible ones.
I wanted to use the special Attachment, but it doesn't support 10mm, so I had to apply it by hand.
With the 10mm Rim sticker, depending on the angle, it looks like the entire Rim is colored, which is cool.
What can I say, the angle is difficult. It's hard to make a circle.
It's a little off, but I'm going to Challenge again when it comes off, so I'm not going to let a little thing get in the way this time.
Degrease it and wet it thoroughly with a thin piece of neutral detergent before applying it.
I match the whole somehow, and when I finish pasting, I adjust it slightly, and finally dry it with Dryer. Or rather, I fix it.
This Dryer was very important.
By applying the Dryer firmly, the Sticker tightens up and absorbs the messy part. I was able to apply the Dryer while tracing it with my finger, and was able to put it on beautifully.
When the Sticker is cooled down, wash it with water to remove the detergent from the Wheel. Now it is completed.
The whole process took about 30-40 minutes.
Yang penting Pengering terakhir.
Saya mulai bosan dengan Pemberontak hitam murni dan perlahan-lahan menambahkan warna.
Saya akan menggunakan Putih untuk stiker Rim, tapi saya pikir akan lebih baik menggunakan warna yang sama dengan Emblem Honda, yang agak mentah dan keperakan, jadi saya memilih abu-abu muda, yang tampaknya menjadi warna terdekat pada Katalog.
Warna sebenarnya yang saya terima adalah warna seperti Titanium yang sedikit lebih gelap (tetapi bukan meta Gun) dan saya pikir itu lebih gelap dari yang saya harapkan, tetapi ketika saya memakainya, warnanya pas.
Lebar pelek OEMWheel REBEL250 adalah 14mm, jadi saya memilih 10mm yang tampaknya paling tebal di antara yang kompatibel.
Saya ingin menggunakan Attachment khusus, tetapi tidak mendukung 10mm, jadi saya harus menerapkannya dengan tangan.
Dengan stiker Rim 10mm, tergantung sudutnya, sepertinya seluruh Rim diwarnai, yang keren.
Apa yang bisa saya katakan, sudutnya sulit. Sulit untuk membuat lingkaran.
Ini sedikit meleset, tapi saya akan menantang lagi ketika itu keluar, jadi saya tidak akan membiarkan hal kecil mengganggu kali ini.
Degrease itu dan basahi secara menyeluruh dengan sepotong tipis deterjen netral sebelum menerapkannya.
Saya mencocokkan keseluruhannya entah bagaimana, dan ketika saya selesai menempel, saya menyesuaikannya sedikit, dan akhirnya mengeringkannya dengan Pengering. Atau lebih tepatnya, saya memperbaikinya.
Pengering ini sangat penting.
Dengan menerapkan Pengering dengan kuat, Stiker mengencangkan dan menyerap bagian yang berantakan. Saya bisa mengaplikasikan Pengering sambil menelusurinya dengan jari saya, dan bisa memakainya dengan indah.
Saat Stiker sudah dingin, cuci dengan air untuk menghilangkan deterjen dari Roda. Sekarang sudah selesai.
Seluruh proses memakan waktu sekitar 30-40 menit.