- Home
- Product reviews
- Motorcycle Parts
- Brakes
- Brake Hose / Clutch Cable
- It looks tighter in Black.... (GOODRIDGE: BUILDALINE Brake Hose Kit)
【GOODRIDGE】BUILDALINE Brake Hose Kit Review
It looks tighter in Black.
[How is it used?
I used it on the rear brake of the XJR1300C, the main vehicle.
Both Caliper and Rear brake master are NORMALSpec. and footpeg is OVER Rear Sets.
This time, we have replaced Brake Pads and performed an Overhaul of the RearBrake Caliper.
We exchanged the wild OEMHose for the stylish Goodridge.
We have selected BlackHose's Black stainless full Black Spec.
I'm happy with how crazy tight it looks.
Was the one you received as per Image?
The texture and product details were as good as the Image.
The connection to the rear caliper was a bit of a surprise because, unlike the OEM, it was a direct stick type to the caliper.
Was the installation difficult?
The installation itself is not difficult, although there is a hose holder on the back of the Swing Arm.
Be sure to go through this Holder, as Goodridge's Hose is much thinner than OEM.
Cut the HoseRubber attached to the OEMHose with a Cutter and wrap it around the Goodridge Hose.
When tightened through the Holder, it is firmly secured.
Also, a note on the air bleed. First, XJR's RearMOSCaliper has Breeder's Quantity:2pc. Since it comes with a Set
Be aware that you have to bleed air from two places, and it's easy to miss the Breeder on the reverse side.
It is very difficult to turn a Breeder with a rear wheel, so short 8mm Glasses are easy to use.
And here's where it gets even more important:Caliper will not release air while locked in its normal position!
Remove the Caliper and lift it to the upper side to bleed air with the Breeder Up.
I was stuck in air venting hell for about 2 hours before I realized this. 500ml of Fluid was also wasted (lol).
How was your experience with it?
The Touch is now very chunky and I don't have to deal with the unpleasant feeling of the OEM's squeezing.
[Included Parts:were they on?
As you can see in the picture I took for you.
[Was there anything that disappointed you?
Nothing in particular, I personally prefer copper for Crash washers, so no Aluminum please!
Terlihat lebih ketat dalam warna Hitam.
[Bagaimana cara menggunakannya?
Saya menggunakannya di rem belakang XJR1300C, kendaraan utama.
Master rem Caliper dan Belakang adalah NORMALSpec. dan footpeg adalah OVER Rear Sets.
Kali ini kami telah mengganti Kampas Rem dan melakukan Overhaul Kaliper Rem Belakang.
Kami menukar OEMHose liar dengan Goodridge yang bergaya.
Kami telah memilih Spek Hitam Hitam penuh BlackHose.
Saya senang dengan betapa ketatnya tampilannya.
Apakah yang Anda terima sesuai Gambar?
Tekstur dan detail produk sebagus Gambar.
Sambungan ke caliper belakang sedikit mengejutkan karena, tidak seperti OEM, itu adalah tipe stick langsung ke caliper.
Apakah pemasangannya sulit?
Pemasangannya sendiri tidak sulit, meski ada dudukan selang di bagian belakang Swing Arm.
Pastikan untuk melewati Holder ini, karena Goodridge's Hose jauh lebih tipis daripada OEM.
Potong SelangKaret yang menempel pada OEMHose dengan Pemotong dan lilitkan di sekitar Selang Goodridge.
Saat dikencangkan melalui Dudukan, ia diamankan dengan kuat.
Juga, catatan di udara berdarah. Pertama, RearMOSCaliper XJR memiliki Kuantitas Peternak: 2 pc. Karena dilengkapi dengan Set
Ketahuilah bahwa Anda harus mengeluarkan udara dari dua tempat, dan mudah untuk melewatkan Peternak di sisi sebaliknya.
Sangat sulit untuk memutar Breeder dengan roda belakang, jadi Kacamata 8mm pendek mudah digunakan.
Dan di sinilah yang menjadi lebih penting: Caliper tidak akan mengeluarkan udara saat terkunci pada posisi normalnya!
Lepaskan Caliper dan angkat ke sisi atas untuk mengeluarkan udara dengan Breeder Up.
Saya terjebak di neraka ventilasi udara selama sekitar 2 jam sebelum saya menyadari hal ini. 500ml Cairan juga terbuang (lol).
Bagaimana pengalaman Anda dengannya?
Sentuhan sekarang sangat tebal dan saya tidak harus menghadapi perasaan tidak enak dari tekanan OEM.
[Termasuk Bagian: apakah mereka aktif?
Seperti yang Anda lihat pada gambar yang saya ambil untuk Anda.
[Apakah ada sesuatu yang membuatmu kecewa?
Tidak ada yang khusus, saya pribadi lebih suka tembaga untuk mesin cuci Crash, jadi tolong jangan Aluminium!