- Home
- Product reviews
- Motorcycle Parts
- Frames / Protections
- Engine Slider / Frame Slider
- Installed on SV650-2022... (BABYFACE: Frame Slider)
【BABYFACE】Frame Slider Review
Installed on SV650-2022
The bolt that mounts the engine needs to be removed and replaced, so it was necessary to support the engine under the jacketc.
I think it is Merit that the installed state is very simple and you can enjoy the NORMAL stylish feeling, not the element that destroys the appearance of the Motorcycle, but since the slider is directly on the Frame, I am concerned about the effect on the Frame picture when it falls over.
If it is just a standing fall, I think Large is strong enough, but if it falls over, the Slider will be hit strongly from the side with a Large Hammer against the Frame with the whole Engine. Therefore, I am worried that the Frame may be distorted. I don't know how much the Frame will be distorted, but it may be affected if you don't step on it to make it fall slowly even if you are standing on the ground. (That is how it is installed.)
However, since the bolt is replaced with a bolt with both screws for penetrating the Engine and Frame at installation, when one of the screws is bent, if you ride without replacing it and take care of the other side this time, both screws will be bent and the bolt will not be able to pull out. If I do not replace the bolt when one of the screws is bent, I will not be able to replace the Frame Slider and will not be able to return to NORMAL because both screws will be bent and the Bolt will not be able to be pulled out.
If your first priority is to protect the engine and car body, Engine Guard is probably safer.
I was torn between the priority comparison of appearance and guard capability, but I decided to go with the Frame Slider because it is a very stylish motorcycle.
Dipasang di SV650-2022
Baut yang menahan mesin perlu dilepas dan diganti, sehingga diperlukan penyangga mesin di bawah jaketc.
Saya pikir itu adalah Kelebihan bahwa keadaan terpasang sangat sederhana dan Anda dapat menikmati perasaan gaya NORMAL, bukan elemen yang merusak tampilan Sepeda Motor, tetapi karena penggeser langsung di Rangka, saya khawatir dengan efeknya pada Bingkai gambar saat jatuh.
Jika hanya jatuh berdiri, saya pikir Besar sudah cukup kuat, tetapi jika jatuh, Penggeser akan dipukul kuat dari samping dengan Palu Besar ke Rangka dengan seluruh Mesin. Oleh karena itu, saya khawatir Frame mungkin terdistorsi. Saya tidak tahu seberapa besar Frame akan terdistorsi, tetapi mungkin akan terpengaruh jika Anda tidak menginjaknya untuk membuatnya jatuh perlahan meskipun Anda berdiri di atas tanah. (Begitulah cara menginstalnya.)
Namun, karena baut diganti dengan baut dengan kedua sekrup untuk menembus Mesin dan Rangka saat pemasangan, ketika salah satu sekrup bengkok, jika Anda mengendarai tanpa menggantinya dan kali ini merawat sisi yang lain, kedua sekrup akan menjadi bengkok dan baut tidak akan bisa ditarik keluar. Jika saya tidak mengganti baut saat salah satu baut bengkok, saya tidak akan bisa mengganti Frame Slider dan tidak akan bisa kembali ke NORMAL karena kedua baut akan bengkok dan Baut tidak bisa ditarik keluar.
Jika prioritas pertama Anda adalah melindungi mesin dan bodi mobil, Engine Guard mungkin lebih aman.
Saya bingung antara perbandingan prioritas antara tampilan dan kemampuan pelindung, tetapi saya memutuskan untuk menggunakan Frame Slider karena ini adalah sepeda motor yang sangat bergaya.