- Home
- Product reviews
- Accessories
- Electrical
- Other Intercom Options / Repair Parts
- For the use of Income.... (MIDLAND: BT PRO Slide Mount)
【MIDLAND】BT PRO Slide Mount Review
For the use of Income.
I have been using a btx2 pro s with a SZ-RAM4 and bought it with Speaker so that I could use it with my new SHOEI Z-8. I was so attached to the SZ-RAM4 that I couldn't bear to retire it, and since I would likely want to use Jet in the hotter months, I decided to keep it too. I decided to keep it, and the question arose as to what to do with Income.
When using Income, the Microphone is available in Included Parts:for full face, and it is sufficient to use the unused one in Included Parts:for the mounting Clamp, but the Speaker and SlideMount need to be replaced or newly prepared each time they are used. However, the Speaker and SlideMount need to be replaced or newly prepared each time they are used.
I thought about changing the Speaker and SlideMount for each season, but I decided to purchase the Speaker and SlideMount because it is troublesome to take off the interior and put on and off each time, and if I just attach the Body, I can use different Helmets depending on my mood. I decided to purchase a Speaker and a SlideMount.
For installation, we decided to use double-sided tape to attach the outside of the clamp, which was not used in the Included Parts:section, to the helmet, but the SlideMount, which we purchased additionally, does not come with two screws to fasten it to the clamp, We had to think of a way to fix it to the Clamp. At first, I was thinking of using one screw for each SZ-RAM4 and Z-8, but I didn't want to damage the screws by applying excessive force, so I decided to prepare screws. However, this was not the Size sold around the corner. I had to buy a clamp to attach the screws, and it cost about 2,000 yen for two small screws. I had no choice but to use the regular screws for the Z-8, and for the SZ-RAM4, which is likely to be used less frequently, I removed the Clamp once, removed the Screw holder from the Clamp, and fixed the SlideMount to the Clamp with 2.5mm diameter Screws and Nut to make it ready to be used. The Clamp was removed and the Screw holder was removed from the Clamp.
As for the wiring, in the SZ-RAM4, the wires were placed inside the helmet, crossing the edge of the helmet, so it was necessary to protect the wiring from damage when the helmet was placed on the ground, etc. In the Z-8, the wiring could be pulled inside the helmet without passing through the point where it hits the ground, etc., so no protection was needed. However, with the Z-8, it was possible to pull the wiring inward without passing through the point where it hits the ground, so no protection was needed, and the wiring was well concealed, making it look very refreshing.
After installation, it works fine and I can now use Income on my Z-8. For this gold price, I would like to see at least a Screw included in the kit.
Untuk penggunaan Pendapatan.
Saya telah menggunakan btx2 pro s dengan SZ-RAM4 dan membelinya dengan Speaker sehingga saya dapat menggunakannya dengan SHOEI Z-8 baru saya. Saya begitu terikat dengan SZ-RAM4 sehingga saya tidak sanggup untuk mempensiunkannya, dan karena saya mungkin ingin menggunakan Jet di bulan-bulan panas, saya memutuskan untuk menyimpannya juga. Saya memutuskan untuk menyimpannya, dan muncul pertanyaan tentang apa yang harus dilakukan dengan Pendapatan.
Apabila menggunakan Income, Microphone tersedia dalam Included Parts: untuk full face, dan cukup menggunakan yang belum terpakai di Included Parts: untuk Clamp pemasangannya, namun Speaker dan SlideMountnya perlu diganti atau baru disiapkan setiap kali dipasang. digunakan. Namun Speaker dan SlideMount perlu diganti atau disiapkan baru setiap kali digunakan.
Saya berpikir untuk mengganti Speaker dan SlideMount untuk setiap musim, tetapi saya memutuskan untuk membeli Speaker dan SlideMount karena merepotkan untuk melepas bagian dalam dan memasang dan melepasnya setiap saat, dan jika saya hanya memasang Bodi, saya dapat menggunakan yang berbeda Helm tergantung mood saya. Saya memutuskan untuk membeli Speaker dan SlideMount.
Untuk pemasangan, kami memutuskan untuk menggunakan selotip dua sisi untuk memasang bagian luar penjepit, yang tidak digunakan di bagian Termasuk: bagian, ke helm, tetapi SlideMount, yang kami beli tambahan, tidak dilengkapi dengan dua sekrup untuk kencangkan ke penjepit, Kami harus memikirkan cara untuk memasangnya ke Penjepit. Pada awalnya, saya berpikir untuk menggunakan satu sekrup untuk setiap SZ-RAM4 dan Z-8, namun saya tidak ingin merusak sekrup dengan memberikan tenaga yang berlebihan, jadi saya memutuskan untuk menyiapkan sekrup. Namun, ini bukanlah Ukuran yang dijual secara instan. Saya harus membeli penjepit untuk memasang sekrup, dan harganya sekitar 2.000 yen untuk dua sekrup kecil. Saya tidak punya pilihan selain menggunakan sekrup biasa untuk Z-8, dan untuk SZ-RAM4, yang mungkin lebih jarang digunakan, saya melepas Penjepit sekali, melepaskan dudukan Sekrup dari Penjepit, dan memperbaiki SlideMount ke Penjepit dengan Sekrup dan Mur berdiameter 2,5 mm agar siap digunakan. Penjepit telah dilepas dan dudukan Sekrup telah dilepas dari Penjepit.
Sedangkan untuk pengkabelan, pada SZ-RAM4, kabel ditempatkan di dalam helm, melintasi tepi helm, sehingga perlu untuk melindungi kabel dari kerusakan saat helm diletakkan di tanah, dll. -8, kabel dapat ditarik ke dalam helm tanpa melewati titik menyentuh tanah, dll., jadi tidak diperlukan perlindungan. Namun, dengan Z-8, kabel dapat ditarik ke dalam tanpa melewati titik di mana kabel tersebut menyentuh tanah, sehingga tidak diperlukan perlindungan, dan kabel tersebut tersembunyi dengan baik, sehingga terlihat sangat menyegarkan.
Setelah instalasi, ini berfungsi dengan baik dan sekarang saya dapat menggunakan Penghasilan di Z-8 saya. Untuk harga emas ini, saya ingin melihat setidaknya Sekrup disertakan dalam kit.