- Home
- Product reviews
- OEM Parts
- CRANKCASE
- Parts that rarely break - Rare Case (LOL)... (HONDA OEM Motorcycle parts: Flywheel COMP.(Mistuba 31110GT0008)
【HONDA OEM Motorcycle parts】Flywheel COMP.(Mistuba 31110GT0008 Review
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB70, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA BENLY50CD90,
Parts that rarely break - Rare Case (LOL)
Flywheel has been replaced!
I don't have a Pin, even though it's called Flywheel. (;・∀・)
→ I replaced it because it was rusted.
Flywheel
。 It stores the rotational energy generated by the engine and transmitted to the crankshaft, supplies it to the drive wheels, and helps the engine to rotate by inertial force. The crankshaft is the engine's weight. It is neither too light nor too heavy.
[Flywheel has a glitch.
‥
▲Clutch will not disconnect, when Clutch is connected. "Skinny The symptoms include vibration and abnormal noise.
▲Idling is not stable and vibration increases.
By the way, in my case, I felt a strange noise when changing GEAR and Idling was going up and down (lol).
→ I thought it was because the weight had changed due to corrosion from rust or something.
In fact, Flywheel is basically not subject to much wear and tear, and with typical use can often last as long as the life of the vehicle body.
*On the contrary, when it becomes unusable, → corrosion or chipping.
Replacement Procedure]
1) Remove the middle nut with a universal holder and a socket wrench. 2) Remove the middle nut with a socket wrench.
↓
(2) Remove Nut and Washer.
↓
(3) Screw in the head of the Fly Wheel Puller.
Prepare for the Fly Wheel Puller, because it cannot be removed without the Fly Wheel Puller.
↓
(4) Since it is an Opposite Thread Screw, it is tightened by turning it counterclockwise.
↓
(5) Screw in the puller screw. 。 Normal Thread Screw.
↓
6) Place the MONKEYSpanner between the Head and push the bar down to easily pull it out.
↓
(vii) By turning the Shaft of the Puller and pushing in the head of the Crankshaft, the Flywheel comes out in front of the Flywheel.
↓
Replace ?Flywheel and assemble with ?→?.
[After exchange]
◎The noise during Gear changing is gone.
◎No strange vibrations 。
I think Rust caused this symptom because the Flywheel was not performing normal rotation and rotation timing.
It is rare that Flywheel cannot be used, but you should check it when you feel the symptoms or have a chance to open the crankcase.
Especially for older CUBs.
Bagian yang jarang pecah - Rare Case (LOL)
Roda gila telah diganti!
Saya tidak punya Pin, padahal namanya Flywheel. (;・∀・)
→ Saya menggantinya karena berkarat.
Roda gila
。 Ini menyimpan energi rotasi yang dihasilkan oleh mesin dan ditransmisikan ke poros engkol, memasoknya ke roda penggerak, dan membantu mesin berputar dengan gaya inersia. Poros engkol adalah berat mesin. Tidak terlalu ringan dan tidak terlalu berat.
[Roda gila mengalami kesalahan.
‥
▲ Kopling tidak akan terputus ketika Kopling terhubung. "Kurus Gejalanya berupa getaran dan kebisingan yang tidak normal.
▲ Pemalasan tidak stabil dan getaran meningkat.
Ngomong-ngomong, dalam kasus saya, saya merasakan suara aneh saat mengganti GEAR dan Idling naik turun (lol).
→ Saya pikir itu karena bobotnya berubah karena korosi akibat karat atau semacamnya.
Faktanya, Flywheel pada dasarnya tidak mengalami banyak keausan, dan dengan penggunaan biasa sering kali dapat bertahan sepanjang masa pakai bodi kendaraan.
*Sebaliknya, jika tidak dapat digunakan, → korosi atau terkelupas.
Prosedur Penggantian]
1) Lepaskan mur tengah dengan dudukan universal dan kunci soket. 2) Lepaskan mur tengah dengan kunci soket.
↓
(2) Lepas Mur dan Mesin Cuci.
↓
(3) Kencangkan kepala Penarik Roda Terbang.
Persiapkan Fly Wheel Puller, karena tidak bisa dilepas tanpa Fly Wheel Puller.
↓
(4) Karena merupakan Sekrup Berulir Berlawanan, maka dikencangkan dengan memutarnya berlawanan arah jarum jam.
↓
(5) Pasang sekrup penarik. 。 Sekrup Ulir Normal.
↓
6) Tempatkan MONKEYSpanner di antara Kepala dan dorong palang ke bawah agar mudah menariknya keluar.
↓
(vii) Dengan memutar Poros Penarik dan mendorong kepala Poros Engkol, maka Roda Gila akan keluar di depan Roda Gila.
↓
Ganti ?Flywheel dan rakit dengan ?→?.
[Setelah pertukaran]
◎ Kebisingan saat mengganti gigi hilang.
◎Tidak ada getaran aneh 。
Menurut saya Rust menyebabkan gejala ini karena Flywheel tidak melakukan putaran dan pengaturan waktu putaran secara normal.
Jarang sekali Flywheel tidak bisa digunakan, namun sebaiknya periksakan saat merasakan gejalanya atau sempat membuka bak mesin.
Khusus untuk CUB yang lebih tua.