Appearance Refreshing

It's warm and looks simple, so it's great. View detail

In OEMHelmet holder

I have not been able to install it yet because the weather has been rainy on my vacation since I purchased it, but as far as I have checked Reviewetc., I think it is a highly satisfactory product.
Since the OEMHolder cannot reach the Helmet's Holder... View detail

Prevention of Garbage and insect infestation

Oil catch tank Large air open hose installed.
I was always worried that a bug or something might get into it, so this is a relief.

It is Exactly to the OD of Bridgestone's 8mm I.D. Oil Resistant Hose. View detail

Low price, good quality

If it is installed with the product of 's/w motech', we recommend installing this product. However, additional washers are required. Other than that, I can't find any problems with the quality. I am satisfied with the fast delivery and good quality. View detail

Simple and Minimum Helmet Lock Assist

I worked hard to use Wire's Hell lock that came with my new car when I bought it, but this one is one-touch and easy to remove.
I was worried about whether it would fit the inside diameter of the D-can.
Dear Mr. WeBig, It would be helpful to improve the illustration to include the Size of each part of the product in the illustration, so that we can be assured when we purchase the product. View detail

Easier to step on.

Brake pedal was short and difficult to step on. View detail

Convenient to have

It is easy to install and looks like an OEM product after installation.
The Helmet is hidden on the Left Side, so it is good that the Helmet is not visible when taking pictures of the Motorcycle from the Right Side. View detail

Flashing relay

GSX-1000 L3 is installed.
Since Relay is in the Blue circle, it is easier to Rose Seat Cowl as much as possible, and since Relay itself has a protrusion to prevent it from falling out, Space is needed to knead it lightly with Minusetc.
Things are OEM same etc. and not so good or not so good. View detail

Necessary and sufficient

Solidly made, thick and strong enough.
It is necessary and sufficient since it is installed for the purpose of preventing distortion and bending of the Number. View detail

… Failure.

It is not attached to the '23 model because of a model type mistake.
I gave it to a friend. View detail

It's best

Installation is so easy.
Just unplug the headlight and connect it to the blue service wire.
It fits perfectly with the Hunter Curve and has a good sense of unity.
The only downside is that it is not waterproof when it rains.
You need to quickly unplug the USB and close the lid.
It would be even more perfect if it was supplemented to make it waterproof even with USB installed.
thank you -------------------------------------------------- -------- Installation is so easy. Just unplug the headlight and connect it to the blue service wire. It fits perfectly with the Hunter Curve and has a good sense of unity. The only downside is that it is not waterproof when it rains. You need to quickly unplug the USB and close the lid. I think it would be even more perfect if it was supplemented to make it waterproof even when USB is installed. thank you Powered by Google Translator View detail

Too hot.

It was installed on a VST 1050.
Installation is a relatively simple process that can be completed as long as the power supply from the car body is available. The thin seat shape makes the grip feel very comfortable.
I tried it on a March run at about 10 degrees Celsius and it warmed up quickly with Switch-on.
I thought it was warm, but soon it became as hot as if I was holding a hot can of coffee, and I turned off the Switch after about 5 minutes. After that, I would put it back on when my hands got cold.
It is probably at about 70 degrees, but I was concerned that this would damage the Grip's Rubber if used for long periods of time.
Also, the power consumption is about 30w, which is about the same as Headlight, so it may not be suitable for SmallEngine Displacement Volume, which is limited in the amount of power it can generate.
It would be appreciated if the temperature switch could be set to high, low, or off. View detail

Lowest

The product was guaranteed to fit but could not be installed. View detail

Number Protection

I installed it to prevent the Number from bending. So far, it works well because it does not bend when it hits.
Also, it's very heavy. View detail

I was resistant to Funnel, but ??

I was afraid that the Funnel would suck in Dust, Garbage, etc., but I am not worried because of the inner and outer double Net and the Sponge-like Filter. 。 The air is more beautiful than the previous Power FilterSpec. The best thing is that it is lighter than that, and it is a recommended point as a vibration countermeasure for 2-stroke carburetor. ?? View detail

Good design and ease of use

It was used for YAMAHA's DT250.
The design of this one is a Grip using VINTAGEMotocross, and it looks SO good.
In addition to its appearance, the grip is the most comfortable! The hand does not shake even when driving on rough roads, allowing you to drive with peace of mind.
The other day off-road driving was no problem! View detail

Rubber hose is consumable!

[How is it used?
Used for SUZUKI/CHOINORI Fuel Hose and Negative Pressure Hose.
I purchased this product to replace the hose that had been attached to my car because it had deteriorated over time.

How was your experience with it?
It is brand new Rubber so it is very soft.
Does this make it easier to get the fuel down? I think it has become easier.

How did it compare to other products?
We selected KIJIMA because it was the one with the lowest gold price, although other manufacturers also offer similar products.
I am glad to hear that it is working fine.

[Points to note]
You will be handling Gasoline, so be careful not to ignite it. View detail

it's recommended

I think the price is right for everything.
Plus it looks a lot better. View detail

Mount bar for CROSS CUB

I found this product when I was looking for a mount bar to attach additional meters.
Since the installation was requested by the Shop, the details of the installation method are unknown, but it appeared that the Meter panel was removed and this product was co-tightened using the included Bolt.
The bar is now in a position that is very easy to see when driving.
Attached to the bar is an iPRO ShiftIndicatorAPH8 Red ・ SP MukawaΦ48Small DN Tachometer 12500rpm (with Rev indicator) ・ NeoFACTORY48mm Voltage Meter White Panel Stainless

When installed at the same time as the KITACO Neck Cover, modification is required for either one of them due to interference. (Modification of the Neck Cover is recommended.) View detail

Kijima ACC branch harness kit

I haven't installed it yet, but it's good because the quality of the product and the product are excellent. I'll use it well. Thank you for the meticulous packaging and sending. View detail