A4 Size is good.

Size is A4, so it is easy to handle.
The fact that it is not in a volume is good because it can be handled without Habit being attached. View detail

Reflects light well and contributes to safe driving.

I bought this for Repair because one day I was parking my Motorcycle on the parking lot and it was stripped by the Prank. I am very happy that I was able to attach it to a Fender Eliminator made by another company. The shape is cool too! View detail

Purchased for CB750four

I expect Magnet effect because I have had iron powder mixed in before. View detail

Good heating grips!

It's a really good product. Both the finish and the design are excellent. Thank you for your prompt delivery. I recommend this product to others, too View detail

Effectiveness is good, glad I bought it.

[How is it used?
Exhaust System of Z900RS was replaced and Silencer was Bullet Silencer by K-FACTORY.
The kit came with two baffles, one for the outlet and one for the inlet, and the combination of the two was supposed to allow adjustment of volume and exhaust pressure.
When the outlet type was installed, it sounded like a large dump exhaust system and I could not bring myself to use it. The exhaust resistance of the inlet type was too large and the volume went down a little, but at mid-speed or higher, the exhaust clogged and the large width performance went down.
So, I thought there must be a way to lower the volume while maintaining a reasonable exhaust resistance, so I used this product.

Was the one you received as per Image?
As per Image as I had seen the actual product at the store.

Was the installation difficult?
There is no difficulty if you choose a Size that fits within the inside diameter of Silencer.
However, the Silencer exit diameter is 55Φ for use with Bullet Silencer,
The inside of the punching pipe had to be 45Φ so it was necessary to fill the 10mm gap at the exit.
I looked for a gasket that would fit, but could not find one, so I wrapped a heat-resistant aluminum tape around it.
Also, the Silencer fixing bolt that came with the kit was a retro black ordinary Hexagon bolt, so I used a silver cap bolt that I had on hand.

How was your experience with it?
The volume did not go down as much as I had hoped, but at the moment of startup without any Absolutely not!" The explosion was so loud that it felt like "I know it's annoying, but can you forgive Limit?" This was the Level that
Unlike the Silencer-attached baffle, the Straight structure is maintained, so exhaust resistance is not increased excessively, and the sound quality is not muddy and high-frequency components seem to be suppressed.
In terms of performance, it is not too much at low speeds, but it is not too much at high rpm, and it is not too much at high rpm.
However, the Bullet Silencer, which I almost gave up using because it was too noisy even though I like the look of Large, is now available, and the Silencer is also black and retractable, so it is unobtrusive and I am glad I purchased it.

[Included Parts:were they on?
None in particular

[Was there anything that disappointed you?
It would have been nice if the volume could have been a little lower, but then it would have been a poof clogging.
Once again, I felt that the OEM Exhaust System is well made. View detail

The APE can be found at ・・・・

I purchased this carburetor and installed it in order to prevent dust from being sucked into the carburetor while driving on the street, but the intake resistance was much greater than I had imagined. In addition, the carburetor protrudes to the Right on the APE, so the Rubber that stops the Net when the carburetor hits the thigh while driving is not able to be used.
Gap and before I knew it, Net and Sponge were gone. Now I am using Funnel with JAM's 3D Air Filter (Right Side Cover needs to be removed or partially cut). View detail

scratch-resistant

I will put it on the area where it rubs. I hope it will be effective. View detail

cut out and use

Cut out and affix to the area of interest in Motorcycle. View detail

Magnetized, higher than OEM

I always use OEM, but this time I switched to KIJIMA's Magnet. We will see how it goes. View detail

You look good.

[How is it used?
XR230 Used for Valve Matching

Was the one you received as per Image?
Image

How was your experience with it?
We have completed the Valve matching process without any problems.

[Points to note]
It is a small package, but there is so much in it that you can't use it all.
No problem! View detail

Filter part is pricey

If you want to put a Filter between the Fuel lines, it is difficult to bend the Hose if it is short, but if it is angled like this product, it will be neat. View detail

Thank goodness it's readily available.

I used KIJIMA oil for replacing the oil in my KLX230R. I bought KIJIMA oil because it takes a long time to deliver OEM products and they are often more expensive than the Replacements. I was able to replace the oil without any problems. View detail

Necessities

The OEM helmet holder position on the ninja OEM would not allow the helmet to hit the footpeg, so I added this. It is very easy to use and I wonder why I didn't put it in this position from the beginning. The t30Screw is coated with a screw loosener when removing the helmet lock, so be careful not to lick the screw. View detail

It's just like that.

[How is it used?
To prevent paint from peeling and rust on my KLX125 that I bought with the intention of using it for mud play etc. Let's put a Film on the Frame." I decided to try something other than a transparent protective film, and after examining various options, I arrived at this product.
How was your experience with it?
As of 2024, similar products are available from various manufacturers at reasonable prices, but at the time of purchase (about 10 years ago), there were few of this type of product and it involved a fair amount of expense.
However, the adhesive strength of the film is high due to the fact that it is Seat made by 3M, and it is a very good product because it can be firmly attached to round pipe-shaped areas and some unevenness with heat from Dryeretc.
the last "Carbon Style" So, if you look at it up close, you can easily identify it as a fake product, but if you look at it from a distance... it is not so bad.
How did it compare to other products?
At that time, there were still few products of this kind, and there were no comparable products at the time of purchase, but compared to similar products in recent years, the adhesive strength is not inferior, and it is hard to peel off at the place where the adhesive is firmly attached by following the procedure. The adhesive is so secure that it is durable as long as you do not intentionally peel it off even when washing your car using a high-pressure washer.
[Points to note]
Free to Cut Seal." So, make sure to carry out the process before applying (Rust, dust and oil removal, etc.).
Other items that would be helpful
The deciding factor in the purchase
Strong adhesive strength to fix even OEMAeropartsetc. of a car with Double-sided Tape. Made by 3M. I think this was the most important factor in selecting this product.
[How is it used?
As mentioned above, it is used to prevent Wound on Frames and other steel product parts that would look bad due to Rust or scratches if left in place.
【Included Parts:presence or absence】.
One 300×400mm Seat and one sheet of paper with product description & how to paste Guide.
[ITEMS TO BUY TOGETHER
If you want to use it on a complicated shape or over a large area, use a degreaser (parts cleaner, Enamel thinners, etc.), and if you want to use it on a place where you can see if it is rusted, use a rust remover (wire brush, sandpaper, chemical products, etc.) and a rust remover afterwards. and a rust remover afterwards.
If you have a pen-shaped art knife (Scissors or Cutter) for shaping, it will be even easier to cut the excess portions.
Opinions and requests to Manufacturer.
It would be useful to have a larger (500×1000mm or so) film for wide-area use. View detail

Necessities

The OEM helmet holder position on the ninja is not good enough for the helmet to hit the footpeg, so I installed this. It is very easy to use and I wonder why it was not in this position from the beginning. When you remove the helmet lock, you have to remove the t30 screw, but be careful not to lick it, because the screw lock is painted and very hard. View detail

Be careful and read before you buy this.

This grip could not fit to your motorcycle. Even if the product describes you can use this, it may not be on your bike. I got one cuz it was supposed to fit my bike but it didn't. so I asked it seller(the brand Kijima) and they replied that 'This item is not compatible with Eliminator 450. Eliminator 450(US imported version) and Eliminator 400(Japanese domestic version) are completely different motorcycles. So I asked about the dimensions of the handlebars to official Kawasaki global and they replied 'The diameter of the EL400's handle bar is same as that of EL450's.' I sent this reply to the seller and got the reply 'The compatibility information on our website states that it is universal. Therefore, some processing may be required. Please understand that if a customer buys the wrong item due to a confirmation error, we cannot accept returns / refund.'. When I received this message, I gave up to claiming it and decided never to buy anything from Kijima. View detail

cc110 smart phone device

It is integrated with the windshield.
Good safety features as it is in an easy-to-see position. View detail

It's perfect

We had a Dealer install it on a BMW R1250R in 2023!
The labor cost was 1,650 yen.
Very useful. View detail

It was useless.

It was guaranteed to fit the gs125e, but the size did not fit and it could not be installed.
I offered to process the return, but at first they tried to process the return for my convenience.
After that, the return was processed as a warranty of conformity. I looked for alternatives, but there weren't any." But that was not the case,
I looked up the model number of the Clutch lever myself, and found that webike handles the OEM Product. You didn't look for it?
I purchased that one and installed it, and of course it was installed without any problems!
The warranty of conformity is wrongly stated, OEM Parts can't be found, and trust is lost...
Everyone should be careful when purchasing. View detail

Very happy with purchase

Bought this as a north American buyer, received the item 4 days later, perfect packaging. The light diameter is the same as the OEM on the Yamaha XSR900. Very please with the quality of the product. View detail