Reviews
It looks good
When I combined the ratio of Lever's MASTER to Release's MASTER at 1:1, it became heavier than OEMWire.
The Brake was also replaced together, so it is unified and looks very good.
View detail
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
About HuOakDamperKit
Without recognizing what would be the HuOakDamperKit
I got it by mistake, but I'm not in a position to confirm the effectiveness of the installation yet, but will in the process of using it in the future.
I was puzzled by the fact that no explanatory material was included in the package when I received it.
Instruction Manuals are also available from other manufacturers at a lower price than this product.
please take good care of it
View detail
Necessary for extending power lines!
This wire is needed for the power line for DAYTONA's Radar to be a direct out instead of USB.
The KITACO power supply extraction unit is placed under the Rear Sets and wires are extended from there to the Front.
Wiring is a hassle, but once it's on, it's perfect!
View detail
It's good.
The effect is... I honestly don't know.
Atmosphere. www.
View detail
Usage in Touring
I think the design is elegant and parenthesis is good. I think there is no problem if the work is done according to the ad vise. However, my impression after actually using it for touring is that it loses grip. I don't mind if I use it for a short time, but when I use it for long two or at high speeds, it slips and I get tired of changing my grip repeatedly, which makes it large and tiring. Now I have to use anti-slip spray. View detail
purchasing a spare part
When I changed the Mission oil, I replaced it with a new one and used the spare, so I had to repurchase it.
If the size is right, it doesn't have to be HondaOEM, but similar products are not that cheap, so I bought the same HondaOEM Product.
View detail
Replace with new one
Fuel Hose seems to be deteriorating, when was the last time you replaced it? It was so long ago that I don't remember when I replaced it, so I bought it to replace it with a new one before it leaked.
It was a great help because it was a HondaOEM Product, the same thing, and not that expensive.
View detail
Fits: Others , SUZUKI DL1000 V-STROM1050, YAMAHA TENERE700, HONDA CT110, DUCATI SCRAMBLER, SUZUKI V-STROM250, BMW R1150GS, KAWASAKI NINJA250, YAMAHA XSR700, HONDA CB400SUPERBOLD'OR
PCX160 8BK-KF47 Mounting on
Purchased for daily use such as shopping for two and for overnight touring.
The installation is done with multiple one-touch belts, so anyone can do it.
However, if the Belt to be installed is Quantity:Pair (for Left and Right) somewhat on Seat's buttocks as it straddles the
Interference.
The capacity is large enough to hold a helmet and many other items.
The waterproof property is also excellent, so rain will not be a problem.
The flap (lid) is held in place with magic tape to make it waterproof,
This guy is super powerful. (Lol) The one-touch is not easy to open and close.
However, it is unavoidable in order to maintain the waterproof function.
View detail
Power will be increased, but it cannot be driven on public roads.
I installed it on a 21 year old HPS300. DECATALIZZATORE As stated, this is an exhaust pipe for Race without a built-in catalyst. It cannot be used on public roads.
KITACO Exhaust Gasket XH-09 was used.
The weight of the product is about 2 kg, and since the OEM exhaust system weighs about 5.2 kg, a weight reduction of a little over 3 kg can be expected. The power improvement in the low-speed range can be felt quite clearly, and the feeling of shortness of breath under 4000 rpm is gone. The volume is very large.
The OEM Exhaust End was used as is for installation, but (perhaps due to the newer model year of the Both Sides, or perhaps due to individual differences in the product itself) the joint with the Exhaust End was too short, and the tightening with the band was not secure.
Joint gasket is made by KITACO JPK-3. (φ37×φ32) However, the outer diameter was too large, so we could not install it properly. Since it was troublesome to find a substitute, we used heat-resistant aluminum tape wrapped around GRUGRU. It looks a little awkward, so I am thinking of looking for a Gasket of about φ36×φ32.
View detail
Warm is warm
I bought it because my Over Pants that I had used for years were falling apart. the Size may have been wrong, but it was not unusable, so I used it.
It is so easy to put on and take off that it is a big surprise. I thought it was wonderful that I did not have to take off my shoes. On the other hand, I felt a little uneasy because some parts were exposed.
My fears were proven true. The draft was cold. The protected part is warm enough to be hot, but the exposed part is cooled down by the wind. This is how it feels at low speeds in town driving, so the situation may change as the speed range increases.
View detail
Fits: HONDA CB400SF, HONDA CB400SB
MORIWAKIShort TubeFlange
One of the four I ordered had to be shaved a little to fit, probably because of the BALI. For some reason, one of the bags was also in a different bag. View detail
Fits: HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
I bought it just for the color.
I won't know for sure until I ride it for a while, but I bought it just for the color, so I am not particular about its performance. View detail
Too hot.
It was installed on a VST 1050.
Installation is a relatively simple process that can be completed as long as the power supply from the car body is available. The thin seat shape makes the grip feel very comfortable.
I tried it on a March run at about 10 degrees Celsius and it warmed up quickly with Switch-on.
I thought it was warm, but soon it became as hot as if I was holding a hot can of coffee, and I turned off the Switch after about 5 minutes. After that, I would put it back on when my hands got cold.
It is probably at about 70 degrees, but I was concerned that this would damage the Grip's Rubber if used for long periods of time.
Also, the power consumption is about 30w, which is about the same as Headlight, so it may not be suitable for SmallEngine Displacement Volume, which is limited in the amount of power it can generate.
It would be appreciated if the temperature switch could be set to high, low, or off.
View detail
Does a surprisingly good job.
This is an inexpensive Chinese Case that I have seen on some Site. (Although it has the company name of "Rough &Road" on it.)
It is inexpensive but does the job well. (For now)
It is installed on CT125CT110 HUNTER CUB (JA65), but it seems that Attachment for CT110 HUNTER CUB is not necessary separately and can be installed.
When the case is installed and the Center Stand is applied, the front of the case rises up like Seesaw. (Rear load Large)
Case surface is pear, satin, matte, textured and very dirty. Dust sticks to it.
View detail
For buttock pain!
First I bought Pants with Cushion for Road motorcycle sold on Amazon before I bought this product.
Not very effective and bought this geLupinz.
As thick as they look, they are a bit uncomfortable after getting off the Motorcycle, but they are effective in preventing buttocks pain.
I think it is more effective than Seat's processing.
View detail
Washer diameter is Small
I used a 25mm Spacer to adjust the angle of the windshield on my CRF250RLY50, so I used this washer when I changed the fixed bolt.
The OEMScreen Fixing Bolt has a 13mm diameter UrethaneWasher and the color is Black, so I purchased this BlackWasher, but the diameter is too small, so I am not sure why. Even if the color is different, I would rather purchase a regular Stainless SteelWasher to protect the UrethaneWasher, because I can choose various sizes.
However, this BlackWasher itself is a very good quality product.
View detail
It was bigger than I expected.
I ordered 1 Size Large as other manufacturers do to wear inner protector, but it was too large.
I thought about replacing them, but it's a hassle and the Large also doubles as a Small, so I'm wearing them shrunk with Belt.
However, it's not a good look.
View detail
Black still seems to be vulnerable.
Used outdoors in full sun for less than 1 year and 2 months after purchase.
What was originally Black has faded and turned gray.
It also tore like a rip, so I had to use curing Tape to plug the hole for now. Is it still susceptible to deterioration by sunlight if it is Black?
I am using two more in parallel, Black and Silver. the Black is about a year old. It has faded a bit but still seems to stand up to the test.
I thought I was using them the same way, but I am wondering how a difference of two months can make such a difference.
Silver is about 5 months old. It is still clean.
I was lucky that the exhaust pipe was not touched.
Since the original price is over $8,000, it would be nice to have a little more durability. However, the Motorcycle Cover is a consumable item. However, Motorcycle Covers are consumable items, so I am not that dissatisfied with them since they cost around 4,000 yen at Sale and I prefer black. But I think I will get the Silver color next time.
View detail
Shallow angle
It came with a 10° Handlebar, which felt a bit tight, so I bought an 8° Handlebar.
Only drilling of the switch box is required, but I am satisfied because the position is relaxed and the front load is not lost.
View detail