Reviews
![[Short Lever] Brake Master Cylinder Kit [Horizontal Type 1/2-inches/Tank Separate Body Type]](https://img.webike-cdn.net/catalogue/images/105373/43336_TS.jpg)
Matching with Caliper
Purchased a 1/2-inches diameter short lever to replace the front caliper with a Brembo crab caliper.
Piston diameter 32mm in combination with Caliper (hydraulic pressure ratio 6.35) is
No Control at all with stiff Touch.
Piston diameter 34mm in combination with Caliper (hydraulic pressure ratio 7.17) is
Good Controllability, although a little softer than the preferred Touch.
If it were a standard Lever, would the former combination have been acceptable?
View detail
![[Stock Lever] Brake Master Cylinder Kit [Horizontal Type 1/2" / Tank Separate Body Type]](https://img.webike-cdn.net/catalogue/images/105373/61739_TS.jpg)
Used for MAJESTY 125 FBrakes custom
The MAJESTY125 and R1-Z have the same 83mm Pitch of the front brake caliper, so I used the R1-Z's caliper and changed the front brake to 4POD to strengthen the brake. So, I wanted to lower the Piston size of MASTER, and I wanted to be able to adjust the lever play by Dial as well as CB1300 Caliper, and I wanted to use a short lever. I also wanted to use short lever, so I replaced it with Nisshin's MASTER.
As expected, the brake has improved in both touch and braking power due to the MASTER's smaller-diameter piston size,
Now I have a performance problem on the Caliper side and want to replace the Caliper with the SumitomoCaliper from TZr250 after 3MA or the Nisshin caliper with 83mmPitch released from TZ125, TZ250 and AdvantageNisshin in the 90's. I'm looking for a new caliper.
View detail
A little short, a little thick
I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people.
View detail
With reference to your Impression.
I bought one from this Manufacturer based on your Impression. View detail
Good product
Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R1000 R, SUZUKI GSX-R1000, YAMAHA YZF-R6, YAMAHA XSR900, YAMAHA YZF-R1, YAMAHA TRACER900, YAMAHA TRACER900 GT, YAMAHA MT-10 SP, YAMAHA MT-10, YAMAHA MT-09 SP, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA FZS1000FAZER, YAMAHA FZ1-S FAZER, YAMAHA FZ1-N FAZER, KAWASAKI ZZR250, KAWASAKI ZEPHYR400
Highly durable Steel
Used on first generation Ninja 250R.
Is this OEM or is this the only Sprocket that's steel and highly durable?
I prefer Black Sprocket, so if that's the case, my options are narrow.
I like the look of Parenthesis.
The paint job is also Beauty, so it is comparable to Duralumin products.
I mean, Material:So much more expensive than Aluminum...
Installation is DIY.
No special sukill will be needed.
Lock nut is also black because it is black.
View detail
I have no particular problem using it.
It is a consumable item that is used for a short period of time, so it is very helpful to be able to purchase it at a reasonable price. I have no problem using it. View detail
To match the Gold amount up to free shipping.
As per Title, I bought it to get free shipping.
We strictly follow the routine of one in every two Oil changes, so this is fine.
This one also has an O-ring attached, which is convenient.
There were two types of large O-rings in the package. I used the one with the smaller diameter wire, but I think it is fine.
Is it because of these two types of O-rings that I feel like there are so many compatible car models listed?
A certain "Kansai Soul", which is only cheap, is poorly made, but I think this one can be used with peace of mind.
View detail
Genuine DID replacement chain link
As I said before, I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERV7 is one I do not surrently have in stock so no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. These chains are generally used on tracxk bikes from a 530 or 525 conversion so I do use a lot of them. As you can imagine, I go through a lot. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
Fits: HONDA CBX125F, HONDA NSR250R, HONDA CBR250R, HONDA VFR400R, HONDA Integra, HONDA CBR400R, HONDA SUPER BOLDOR, HONDA CBR300R, HONDA RVF400, HONDA CB400SB, YAMAHA TZM50R, YAMAHA YZF-R125, YAMAHA TZR250, YAMAHA YZF-R15, YAMAHA YZF-R25, YAMAHA FAZER, YAMAHA FZR400RR, YAMAHA YZF-R3, YAMAHA YZF-R6, YAMAHA XJ6
First MirrorBlinker installation
I put it on a yzf-25r early model.
Screw holes don't meet at all, so I have to rebuild them.
It must not be done. It is absolutely impossible for an amateur.
View detail
When in doubt, SUNSTAR
Balance of lightness and durability, true circle, etc.
In terms of color variations and price, the xam is the better choice.
For now, you can't go wrong with SUNSTAR.
View detail
exchange
I bought this for a ZZr250 Rear Sprocketfor replacement, it is lighter than the OEMSprocket and looks better in Gold. It is an applicable product and I was able to install it without any modification. View detail
Accurate and lightweight
I bought this for Circuit.
For MINICourse is swinging to the side with the show.
Lighter weight compared to OEM helps reduce load under Spring.
View detail
Purchased for CB750four
I expect Magnet effect because I have had iron powder mixed in before. View detail
For CB250F
.Actually this item i could not found in my country (VX Series Joint Link 520VX3). Finally I bought it from webike. It is original. Very good packaging.fast shipping.I am happy to deal with the webike team View detail
Element is always this!
Required Packing on OEM Equivalent Product (excluding Drain Washer) It is easy to use because everything is included in the package. View detail
Magnetized, higher than OEM
I always use OEM, but this time I switched to KIJIMA's Magnet. We will see how it goes. View detail
Parenthesis OK
Circuit to change Final
Purchased
OEM's number of Chain links.
It cannot be installed.
The number of LINKs needs to be increased.
Changing the Chain is a Large oddity.
I changed Front's Sprocket to 13 guns.
Steel, but light.
View detail
light
I need to change Final to run Circuit.
Purchased
Duralumin and very lightweight.
I also feel that Motorcycle movement has improved.
Durability would be better.
View detail