Reviews
Helpful in preventing Prank
It looks better than the OEM resin cap and requires a hexagonal wrench to open and close, but there is no oil level gauge, so the OEM cap must be kept in stock. View detail
CB750FOil Element replacement!
Good cosmetics Packing is included! Stock and Repeat for next time for Replacement. View detail
Cospa best
Inexpensive and perfect quality
Safe to use
View detail
Perfect for dress-up!
The dress-up effect is great.
It also feels right in use.
View detail
A little short, a little thick
I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people.
View detail
Titaniumium color!
Small but finely crafted
Luxury that you can feel in your hands
Worth the Gold!
View detail
Purchased for a 12 year MODEL ninja 1000
This is the first time I have used this Drain Washer.
I used to use Drain Washer purchased from Motorcycle shop, but I bought it because I ran out of stock.
I don't think it's a problem since it's OEM, but just to be sure, check the area around the Drain Washer after test run after replacing the Oil.
It didn't leak, so it's Large sturdy.
OEMs are secure.
View detail
Small
I bought it for my BMW R1150GS because it fits VST 1050, but it is smaller than I expected. I bought it knowing that it would not fit over the SIDEPannier, but I did not expect that it would not fit over the Top case either. The storage is compact. View detail
I replace them regularly.
This is a small component, but it is a large component that holds Brake Pads.
Rust-resistant Stainless Steel is easy to maintain.
View detail
I have no particular problem using it.
It is a consumable item that is used for a short period of time, so it is very helpful to be able to purchase it at a reasonable price. I have no problem using it. View detail
SUNSTAR Racing Steel Sprocket
Item safe landed..packing was perfect..correct item.my second set for my next change.very good product from sunstar.very surprise package arrived super fast within 3days..well done TEAM WEBIKE!!!.. awesome..highly recommend to shop at webike.thank you.more comming View detail
There was no one with Level gauge.
The OEM Product was not strong enough, so it was replaced. After installation, I found that the flange surface is narrower than the OEM Product, so there is a gap between the OEM Product and the engine side. I would have liked to have had a product that fits Exactly. View detail
Black so it looks tighter.
What made you decide to buy?
Since the beginning of the New Year 2024, I have been gradually collecting parts and trying to carry out a customization that I have been envisioning since last year … that customization is to replace the front rear sprocket and chain. Why did I choose the Sunstar Racing Steel rear sprocket? The reason for choosing the Sunstar racing steel rear sprocket and chain is that the power and traction control of modern supersports are constantly subjecting the sprocket and chain to high and fluctuating loads. Although there is no change in weight with the stock steel and Sunstar also made of steel, we chose a rear sprocket that delivers super durability that can take the power.
[How was the installation?
When replacing the sprocket, you will need a racing stand to lift the rear tire and a long spinner handle to loosen the axle nut. Also, a Torque wrench is necessary for Torque management.
Float the tire on the rear stand, loosen the axle nut, pull out the shaft, and remove the wheel. I always use a scrap tire from a car to put the removed wheel on the stand. I always use a scrap tire from a car to put the wheel on the stand.
While removing the Rear Sprocket, it is a good idea to clean up the area around the back of the Sprocket that has become sticky with the Chain lube. After cleaning, fix the Rear Sprocket, but since there is a little play, fix the Sprocket nut while pulling the Chain in the direction where the Chain is pulled. It is recommended to mark the Sprocket nut to confirm the tightness.
How was your experience with it?
At first, I was not sure if I should reduce the number of pins and make it Long, but I didn't want to have a misprint on the Speed display, and I also liked the ride quality of the OEM, so I decided to use the same 43 pins. So there is no change between before and after the replacement, but the OEM 6R is easier to handle. 21 year old ZX-6R has Front 15T, Rear 43 Dings, Reduction Ratio 2.866, Chain linkage 112.
View detail
To match the Gold amount up to free shipping.
As per Title, I bought it to get free shipping.
We strictly follow the routine of one in every two Oil changes, so this is fine.
This one also has an O-ring attached, which is convenient.
There were two types of large O-rings in the package. I used the one with the smaller diameter wire, but I think it is fine.
Is it because of these two types of O-rings that I feel like there are so many compatible car models listed?
A certain "Kansai Soul", which is only cheap, is poorly made, but I think this one can be used with peace of mind.
View detail
As expected of DAYTONA
Was the installation difficult?
pimping
How was your experience with it?
It's going to look different
View detail
It was EXACTLY!
I purchased this to replace an OEM Oil cap groove that was broken.
It was Exactly in JA10!
View detail
grunting or groaning sound
I was convinced that I could be sure of the products here. View detail
I got a lot of iron powder.
I used it to clean up my new MONKEY125. It was my first and second DIY oil change, but it was done without any problem. View detail
Thank you Plus mu.
I had never used a disc before, so I had no knowledge of how to install it, and when I looked at Mu's installation instructions carefully, I saw a note that said to use two shims for a 4mm disc. However, the box contained only the number of shims I requested. When I called them to ask for an explanation, they responded in detail and kindly. Thank you very much. Thank you very much. I don't know if it is because I bought a slightly old motorcycle used instead of a recent motorcycle, but the floater was removed due to deterioration, and I had to replace it with a new one. But I didn't have the courage to replace a disc with almost no miles on it, and I found Plus mu through the ad-vise of PhoLower. I think that there are people who buy old motorcycles in pursuit of romance, not only my motorcycle. But please don't worry. If you have Mr. Mu's products, even if you are in my situation, you can revive your OEM. I am sure you will be satisfied economically, visually, and in terms of customer service. I apologize for the length of this message. View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail