Reviews
Ideal for lightweight
Installed on 8BK-RG74J.
No loss of horsepower with regulated engines = can be converted by replacing the Exhaust System. but there was not much change at the JMCA, where the regulations are tighter.
In the 250cc class, the Large body only varies by 1 to 2 horsepower no matter which Exhaust System is selected, so this Exhaust System is recommended for weight reduction purposes.
As for the sound, the 8BK is almost 90db OEM, so you hardly notice any change in volume, but some parts have a thicker sound depending on the RPM.
In terms of sound quality, I think you would feel more change with Planus or WR's Slip-on Silencer.
The quality, however, the accuracy of the front pipe was quite poor, and it did not fit neither the Engine nor the Center pipe, so it had to be installed while bending it with Lever.
Although less expensive than other Full Exhaust Systems, it would have been nice to have a more accurate product.
When installing the Silencer, it is recommended to temporarily fix the Exhaust Band and Bracket and then install the Bracket on the body of the vehicle, as it is quite difficult to install the Exhaust Band if you follow the Instruction Manual.
Also, although not mentioned in the Instruction Manual, it was necessary to change the Wiring position of the O2 Sensor.
The OEM position is fixed in front of the Clutch cover, but once removed and placed through the rear.
Although it has a few drawbacks, it does not look like other people's and can be lightened to a large width, so I think it is recommended for people who are visually oriented.
View detail
To remove ACC power from VST250SX...
I used it on a DL1000 V-STROM250SX to take out the ACC power for the DRA RECORDER.
I'm sure it will be listed eventually, but DL1000 V-STROM250SX is not listed as a compatible car model, but it was usable.
It would be nice to be able to get ACC power just by inserting it between the Connectors without damaging the existing Wiring.
View detail
Fits: HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CT110 HUNTER CUB125, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB C125, HONDA Dio 110, HONDA LEAD 125, HONDA PCX 125, HONDA PCX 160, HONDA PCX ELECTRIC, HONDA ADV 150, HONDA HORNET250, HONDA HORNET600, HONDA CB 125R, HONDA CB 250R, HONDA CBR 250RR, HONDA CBR 600RR
Easy to hang and wind resistant. Very good.
I use this Repeater on my CT110 HUNTER CUB and GB250 CLUBMAN. It is my favorite.
I bought it last year when I bought a CT110 HUNTER CUB, because I was planning to add a front carrier and a RODCarrier to it. I am sure it will be a good reference for those who are considering purchasing it.
The front carrier is made of DRC, the largest class, and is fixed at the most forward position, so the front of the handlebar is considerably longer than in NORMAL, The height of the LeftFront section of the Rear Carrier is 10cm higher than the Seat. The lower part of the front wheel and Quantity:Pair (for Left and Right) As you can see in the photo, I can close the RearFastener to the very bottom, even with the bottom rope tightened quite a bit. I live in an area that is occasionally exposed to strong winds, and the Seat has never rolled up.
Also, I have been using it for over a year now and it has not deteriorated much. (There is a short period of time when the parking Space is in direct sunlight.) Not much dirt on it. (It has a roof, so it is virtually dry even in the rain.) and I have never washed the surface with water. I am very satisfied.
I bought it for GB250 CLUBMAN almost one year after CT110 HUNTER CUB. It is rather a little bit large, so the front wheel lower part and the quantity of the front wheel are a little bit smaller than the original size.:Pair (for Left and Right) The Adjuster rope at the bottom is fully squeezed. There is still room to spare, but not so much that it will flip up in the wind, so we are not worried at all.
Perhaps if it were exposed to rain and direct sunlight throughout the day, the evaluation of deterioration might change, but I cannot comment on that.
View detail
Fits: DUCATI SCRAMBLERIcon, DUCATI 1299 Panigale., BMW R1200RS, BMW S1000RR, SUZUKI GSX-S1000, SUZUKI GSX-S125, SUZUKI GSX-S750, SUZUKI GSX1000S KATANA, SUZUKI GSX1300R HAYABUSA, SUZUKI GSX1400, SUZUKI GSX250R, SUZUKI ST250E Type, TRIUMPH STREETSCRAMBLER, SUZUKI VANVAN200, SUZUKI BANDIT1250, SUZUKI DL1000 V-STROM1000, SUZUKI DL1000 V-STROM250, SUZUKI GRASS TRACKER BIGBOY, SUZUKI DL1000 V-STROM650, SUZUKI Intruder Classic
Cute.
Pad thickness is just right and cute.
It would be better if it were cheaper.
View detail
DAYTONA Oil Clean Bolt
Item received.took 4 days to arrived.excellent.very well packed.item is solid.very light than the original bolt.magnet is strong.thank you team WEBIKE..never disappoint.highly recommended to shop. View detail
Lighter than OEM, texture is comparable to OEM, slightly less visible
NINJA400 (2023) I installed it in
The fit is perfectly fine.
It is shorter and lower than OEM and looks better.
Rearward visibility is slightly inferior for this reason, but it can be managed with some adjustments.
(The field of view will be wider, so the result will be toned or slightly harder to see.)
near (near directly behind) Do not do this if you are afraid that it will be difficult to see the
This is for people who have or can have a Habit to make sure they have a good visual check.
So far I don't notice much loosening at high speeds or blurring from vibration.
(OEMs are better in comparison).
View detail
For THRUXTONRS
OEM replacement for Triumph is not available, but if the OD and internal Screws match.
Can be installed. Always change Oil and Drain plug Magnet
This product gives me peace of mind when I look at it and worry about all the iron dust.
Overall length is slightly longer than tiger OEM, but no problem for installation.
View detail
DAYTONA Oil Clean Bolt
Item arrived..as can see,superbe packing since day 1 of my order with webike.product is as advertised.very light and strong magnet.quality good..thank you team webike.. View detail
Good cost performance, OEM same etc. Crimp structure is also safe.
Used to refresh a NORMAL rubber hose that had been used for nearly 40 years since new and had cracks on the surface.
The Crimp is made by NICHIRIN, the same company that makes the OEM Brake hose, and the connection to the banjo section is the same quality as the OEM Crimp.
We purchased this product because it is durable and reliable for long-term use, and it kills two birds with one stone:it also provides a Snap and BrakeTouch as a mesh hose.
Performance is fine.
After installation, the Crimp was not handling well for about a year, and it was pulling tight due to interference with the Cowl Bracket at full lock, but the Crimp did not pull out and the Hose did not break.
In order to reduce in cost and increase reliability, the panjo adapter is fixed and there are only two types of orientation, 90-degree right angle or parallel, for the upper and lower panjos, and only two types of banjo adapter angles, straight or 20 degrees, so you have to choose the type of car to install. The banjo adapter has only two angles, Straight or 20 degrees, so you have to choose the type of car you want to install it on.
View detail
It says it is TMAX560 techmax compliant, but it is completely useless.
I bought it because it was supposed to fit, but it did not match the Screw shape of the Handlebar End at all. I was very disappointed. View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Brake's Stress is reduced.
This is a change from OEM horizontal placement 11mm to 5/8Radial master.
Because it seemed to interfere with the Switch box, the Lever was changed to Eukanaya's (NI002-049),
Nisshin's Tank Bracket (49151) for Separate Handlebars is installed.
As for the banjo fitting, a stainless steel mesh hose (AC Performance line) compatible with the car model was originally installed, but it interfered with the switch wiring, so an L-shaped adapter was used to make an escape.
My impression after installation is that the absolute braking force has not changed, but the controllability has improved.
Specifically, it is an Image with interpolated increments of braking force according to the strength of the grip.
The beginning of the grip is especially noticeable. With the horizontal 11mm pad, the rise in braking force is abrupt, but with the vertical pad, there is a sense of being able to adjust the strength of the pad. The same is true near the end of the grip, making it easier to generate strong braking force without locking.
Probably because the lever ratio and diameter are designed to match the weight of a horizontally mounted 11mm lever, it will not be that uncomfortable (too effective or too ineffective) to replace it. If you want a lighter grip or more strokes, you may want to consider a 14mm or 15mm model such as the F Land-.
In general, I can recommend it, but since it is Large strange to do banjo fitting by yourself, it is safer to ask a supply store with a Pit.
View detail
Replace instead of overhaul 20 year old OEM
The MAJESTY 250 OEM Master Cylinder is 20 years old, the paint is peeling, the fluid level window is white and cloudy, and the touch screen is dead. I thought that if I replaced it with OEM, it would be in the same condition again someday, so I replaced it with this one, which has better accuracy and quality.
The original vehicle had some customization done to the exterior, and the replaced handlebars gave it a more custom look.
I am satisfied that the color of the handlebar matches the color of the MASTER and Lever, creating a sense of unity.
Unlike the OEM, the 6-step lever play adjustment is also highly satisfactory.
Also, we are happy to be able to strengthen the brake with the SKULL Helmet principle by lowering the diameter by 1 Size to 11mm, compared to the OEM MASTERPiston diameter of 1/2-inches.
The brake hoses were stainless steel mesh when they were installed, so we did not have to worry about a large increase in stroke volume, and both control and braking power were improved, resulting in a highly satisfactory brake customization.
View detail
PetitCustom
PetitCustom by Exactly for One Point's color insert!
I installed it as a trial before putting brembo in.
4miniCustom standard color!
View detail
Standard PetitCustom
For Caliper's color insert!
Trial installation before putting brembo in.
4mini standard color:??
View detail
Fits: YAMAHA YZF-R25, SUZUKI Hayabusa, SUZUKI GSX-S750, SUZUKI SV650X, SUZUKI Gixxer 250, SUZUKI V-STROM250, KAWASAKI Z900RS, KAWASAKI ZX-10RR, KAWASAKI Z650, KAWASAKI Ninja250, KAWASAKI W800, YAMAHA YZF-R3, YAMAHA Tenere700, YAMAHA XSR700, YAMAHA SR400, YAMAHA TRACER900, HONDA rebel1100, HONDA VFR800F, HONDA CB1100, HONDA CRF250 RALLY
It is compact and practical.
It is small in size and easy to carry.
If you park outdoors during a long-distance tour, dew will form in the morning and the sheets will often get wet.
Especially in the spring, when pollen gets mixed in and gets messy, it can be really useful.
Lastly, since the material is thin, it is easy to fold and store. -------------------------------------------------- -------- It is small in size and easy to carry. If you park outdoors during a long-distance tour, dew will form in the morning and the sheets will often get wet. Especially in the spring, when pollen gets mixed in and gets messy, it can be really useful. Lastly, because the material is thin, it is easy to fold and store. Powered by Google Translator
View detail
New Master Cylinder while replacing Lever.
[How is it used?
The Yamaha MT-25's Brake lever had been made in China since delivery and I was concerned about rattling.
I was worried about using such a product in Brake, but I was wondering what to do because OEM products are too expensive and other brand products from proper manufacturers are expensive. I was wondering what to do. I realized that if I just refurbished the Master Cylinder, it would solve everything, and I came across this product, which is a NISSIN product with a separate tank.
Was the one you received as per Image?
I have used a different Master Cylinder diameter on a different car model, so it was as per Image.
Was the installation difficult?
In the case of MT-25, of course, there is no need to consider interference with Cowl, so it is almost a simple installation.
The banjo bolt was left in place, and the brake switch was simply replaced since the terminals are exactly the same.
In my case, I had a hard time getting the air out because I had changed to Separate Handlebars.
How was your experience with it?
The OEM and Piston diameter is the same 11mm and the same sideways push, so we did not feel much change in the touch and effectiveness of the Brake.
However, with Lever's new, crisp and accurate, I feel that my peace of mind has increased many times over.
Also, NISSIN Lever's R condition etc. is so exquisite that my fingers do not get sore at all even if I ride for a long time.
It looks better and Repair Parts are readily available, so there is nothing to say about it.
[Included Parts:were they on?
Basic AlmostQuantity:It is a Set, but the Mirror Holder Bolt for M10Pitch 1.25 does not come with it.
Perhaps the M6 Tank fixed Bolt is a mistake.
It just so happened that the original Mirror Holder cap had the same cap, so I was able to use it and get away with it.
[Was there anything that disappointed you?
Not particularly
【Review】
Quantity:Pair (for Left and Right) It is great to be able to refresh the Master Cylinder for about the price of a Lever set.
Anyway, it is very reliable and has the best Touch of Lever and even Adjuster.
I have graduated from the mysterious Chinese Lever and can now ride without hesitation.
View detail
Affordable and easy to use
[How is it used?
Wiring was needed for Circuit Running.
Was the installation difficult?
Copper Washer is included, so there is no need to buy it separately for the first time.
Of course, without the WiringPlate, wiring is not possible, so please purchase and install it separately.
6R is Oil Pan Bolt with Plate bite.
I was reluctant to remove the oil pan bolt, but so far there has been no oil seepage, so I can use it without any problem.
How was your experience with it?
Designability is not particular, but I have no problem with the functionality.
Affordable and easy to use.
[Included Parts:were they on?
Copper Washer and Wire included.
It is a one-time fee and must be purchased the next time it is used.
Point and hang of installation
Wiring should be done by applying tension in the direction that the bolt is tightened. Sometimes we see wiring that is not only meaningless but also dangerous.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA MT-25
Made by Active
[How is it used?
I was looking for a decent lever because I was worried about the rattle of the Chinese lever that had been attached to my Yamaha MT-25 from the time it was delivered, and I was worried when operating the clutch.
OEM or KIJIMA products would have been fine, but I had a desire to customize it a bit, so I chose this product from the trusted ActiveBrand.
Was the one you received as per Image?
I purchased the Black color and it was exactly as pictured.
Was the installation difficult?
Since the clutch lever only needs to be replaced, it can be done in about 10 minutes with ordinary tools.
MT-25 (YZF-R25 also) requires OEM colors and washers, so confirmation is needed if changing from non-OEM.
If the OEM color is not available, it costs about 800 yen, which is high-end for just a color.
How was your experience with it?
As expected from Active, there is virtually no rattling.
I am satisfied with R's finish and the QUALITY of the product.
The play adjustment of the Clutch Wire is also infinitely adjustable, but the length of the Bolt is a bit short. (No problem in actual use in my case)
Also, the meat removal to reduce aerodynamic drag ish cool. I definitely don't feel like I can feel the impact at 250cc speeds, though! (Lol)
[Included Parts:were they on?
LeverBody only.
[Was there anything that disappointed you?
Nothing in particular!
【Review】
There is almost no rattle and the product looks good, so it is definitely better to use this one than to buy a strange Chinese Lever.
Brake levers are about twice as expensive due to their complex shape, so the Quantity:Pair (for Left and Right) If you want to have it all in one place, it will be a bit expensive.
View detail
Fits: BMW K1300 S, BMW F800 S, BMW K1300 R, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA XSR900, YAMAHA YZF-R1, YAMAHA YZF-R250, YAMAHA YZF-R3, YAMAHA YZF-R6, HONDA CBR650 F, HONDA CTX700, HONDA CTX700 N, HONDA NC700 S, HONDA NC700 X, HONDA NC750 X, HONDA NC750 S, HONDA PS250, HONDA VARADERO 125, HONDA VFR1200 F
I like the texture.
CB1300SF, LLSize is just right, Spec. is a little different, but I bought Repeat of the same product. The front and rear tires are also hidden to the bottom. The holes for the front and rear tire locks are thick enough to fit. The back is now black so it is easier to put on. The fabric is thick and durable. The one I used before could be used for 4 or 5 years, but I can't put it on while the exhaust system is hot, so I put on the small one after an hour. I have used other manufacturer's products, but I want to keep my Motorcycle in Large size, so I think I will repeat this next time. View detail
MAXAMRotor bolt
Bolt was replaced along with Disc Rotor replacement.
I originally intended to reuse it, but purchased it because the Hex hole was deformed into a gouge.
Quantities of 3-packs:Buy 2 sets
Since it is a KITACO product, quality should not be a problem.
View detail