Reviews
Fits: HONDA ADV150, HONDA CBR250RR, KAWASAKI Z650, KTM 390DUKE, SUZUKI KATANA, YAMAHA MT-03, Others
Brilliant
Japanese quality, brilliant cases for sport bikes. Looking like custom made for the Suzuki Katana. Tanax needs importer in Europe! View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA MT-25
It is easy to install.
The product is fine, but it can only be installed on the Left Side, and the position is a bit low. View detail
Fits: YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA YZF-R25
It looks better now.
Model YZF-R25
The Rear is quite dirty and it is now clean. the Brake Caliper is OEM and the Pad is DAYTONA, but I am glad I replaced it. The braking power is normally increased and I am satisfied.
View detail
Valuable Exchange
Model YZF-R25
I replaced the Disc Rotor and all front brakes are now brembo. I am very satisfied and it was a worthwhile replacement. You can tell the difference from the moment you change.
View detail
Fits: SUZUKI Gixxer SF 250, HONDA CB1300SUPER BOLD'OR, HONDA NC750X, HONDA CB1300SUPER FOUR, HONDA CRF250RALLY, HONDA CB1300SUPER FOUR SP, HONDA CBR650R, YAMAHA MT-25, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR SP, HONDA CRF250RALLY S, SUZUKI Gixxer 150., KAWASAKI VERSYS-X 250 ABS(17) KLE250D, YAMAHA MT03, Others , SUZUKI V STROM250SX
I thought it would be good for day touring.
The quality looks good, but the capacity is smaller than the picture suggests. The capacity is enough for one day touring. View detail
Fits: YAMAHA YZF-R1, YAMAHA YZF-R1M, YAMAHA YZF-R7, YAMAHA YZF-R6, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT-10, YAMAHA MT-10SP, YAMAHA MT-09, YAMAHA MT-09SP, YAMAHA MT-07, YAMAHA MT-25, YAMAHA MT-03, YAMAHA Tracer9GT, YAMAHA Tracer900, YAMAHA Tracer900GT, YAMAHA MT-09Tracer , YAMAHA XSR900, YAMAHA XSR700, YAMAHA FZ1/Fazer
Very satisfactory product
The finish is satisfactory in terms of both texture and ease of use.
However, the gap between the tank and the cap is a little empty, so we have to be a little careful when washing the car in the rain or when washing the car, but there is no problem because water never enters the tank.
View detail
Genuine DID replacement chain link
As I said before, I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERV7 is one I do not surrently have in stock so no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. These chains are generally used on tracxk bikes from a 530 or 525 conversion so I do use a lot of them. As you can imagine, I go through a lot. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
Has the part number been changed?
I have not seen any particular note, but I assume that if you order with this part number, you will probably receive the one with the -80 suffix, and from the aggregate information on the Net, it seems that some Filters, including the -61 one, have been unified with the new part number (-80 suffix).
It is a bit of a shock to receive a different part number without any explanation, but you will be able to use it without any problem.
View detail
When in doubt, SUNSTAR
Balance of lightness and durability, true circle, etc.
In terms of color variations and price, the xam is the better choice.
For now, you can't go wrong with SUNSTAR.
View detail
It got brighter.
I purchased this because Light was dark.
It brightened up as expected!
View detail
Fits: YAMAHA MT3, YAMAHA MT-25, YAMAHA MT03
Just fit in the current model
It can be installed on the current model (RH21J) MT-03 without any problem.
As is the case with other people's Impression,
Many of the products made by other manufacturers have logos or company names with decorative etchings,
If you are not good at such things, or if you prefer simplicity, this Radiator guard is a recommendation.
The manufacturing process is very solid and simple, which gives the manufacturer a sense of confidence.
View detail
After all, it's OEM!
Along with the oil change, I replaced the Oil Filter. I can't tell if the Oil Filter is good or bad right away, but it gives me a different feeling of trust and security. When I replace it again, it will be OEM. View detail
Fits: YAMAHA DRAG STAR 400, YAMAHA XSR700, YAMAHA XSR900, YAMAHA TRACER900, YAMAHA TRACER900 GT, YAMAHA BOLT, YAMAHA MAJESTY250, YAMAHA MT-07, YAMAHA MT-09, YAMAHA MT-25, YAMAHA MT-03, YAMAHA MT03
Quality good
Side mirror is good quality, matches the look of my bike. However require to order 2 unit. Each order is only 1 side mirror. Hence, i am required to order 1 more side mirror. View detail
Used for MT-25 for Rear
[How is it used?
I replaced the Brake Pads on my MT-25, which I use for commuting and touring, because they were running low on remaining capacity before I knew it.
Although DAYTONA's Red Pad is the iron plate as an external pad, I was curious what brembo's CCCompound was like, so I purchased it.
Was the one you received as per Image?
It was just like the picture.
They are the same shape as the probably OEM Brake Pads that came with the vehicle when it was purchased, and naturally had no problem installing them.
Was the installation difficult?
If you have some maintenance skills, it is easy because all you have to do is remove the rear tire and replace the pad.
The Pad pin of MT-25 is just a pin that prevents it from falling out, so there is no need to worry about Bolt sticking.
Although no particular chamfering was performed, the braking power was sufficient from the start.
How was your experience with it?
The CCCompound is designed for city driving, so it is more mild than the previous pad.
The more the Rear locked up until then, the more it stays rotated without locking up when Brake is stepped on.
Although it is not capable of a heavy brake, it seems to be mild enough for normal driving in town.
I drove on a rainy day, but I did feel that the braking power itself was almost the same even with Large rain.
I have driven about a hundred kilometers since the replacement and there is already a little Brake dust.
This means that it is decreasing, so I think Life is not that long.
Brake Discs seem to be less aggressive, so it may be possible to improve the life of the Disc Side.
[Included Parts:were they on?
Brake Pads only.
Don't forget to Grease as well, as Caliper will also need to be maintained when the pad is removed.
[Was there anything that disappointed you?
It is not a disappointment, but I noticed after installation that the pad is quite conspicuous because of its blue color.
This is even more so with the MT-25, which has almost only Black around the rear.
【Review】
This pad is for street use, even in the rain.
It is not suitable for hard breaking, but it may be sufficient for 250cc for rear.
View detail
exchange
I bought this for a ZZr250 Rear Sprocketfor replacement, it is lighter than the OEMSprocket and looks better in Gold. It is an applicable product and I was able to install it without any modification. View detail
Master cylinder cap
Changed from Green Light to Gold. View detail
XG250 TRICKER
I use it on my XG250 TRICKER.
The Motorcycle Cover is a consumable item, so this thickness is sufficient for this price.
View detail
Ideal for Attachment power supply extraction
Ideal for taking out Attachment power supply
DL1000 V-STROM250SX is designed to be easily inserted into a connector of the same shape by removing the cover under the tandem seat to reveal the connectors.
I think this is a good product because power can be removed without damaging the Wiring.
View detail
Genuine GBRacing Engine Protection Set for MT03 2020
This is a set for the MT03 of a customer who wanted to add a little more protection to the casing of their bike. I have personally used GBRacing many times in the past for both my bike and customers bikes and know they are second to none for protection of you beloved. Finding the correct set was really easy as Webike do list all the models these kits fit which is pretty much the entire R6 range from 2006 to now. I also cross checked this with GBRacing website just to be sure I did not write the wrong number down. Really good price for this set from Webike and pretty much the same as I could source locally here in the UK. Yes, you can get other manfacturers who make sets "like" these but I have my own experience of how well these perform in the event of an off. They do take a good beating but essentially, these are to protect you casings. They also look really cool too. For all you get in this kit, the value for money is brilliant, 3 pieces in total and one of the best set of bolts you could ask for. There is the generator cover and clutch cover and finally the water pump cover. Great price for a 3 piece set. The composite is not just plastic like some of the other kits you can buy, they have a percentage of fibre too for strength and durability. GBRacing have really done their homework here and I can confirm the durability is epic. All was packed out really well and even the small pieces were protected during transit.Upon opening the set box, I was really happy to find all was present and correct, the right amount of bolts etc is always a bonus.Having had previous experience in fitting these, it was a piece of cake. It's pretty much the same for each model anyway. Take your time, set out the individual covers and allocated bolts and it's alot easier than fumbling for the right bolt.The customer is really pleased with this kit and to be honest, I am too. Looks great. Thank you Webike, awesome services. View detail
Kitako Power Extraction Series!
Is it for SEA BASS/Yamaha?
I purchased this for my VSTROM250SX.
If you look for a lump at the bottom of the Rear Sets, you will find a Connector, which you simply remove and insert this Adapter between the Rear Sets.
It is very easy Exclusive Design!
View detail