Reviews
More than I expected.
Product Name
NGK NGK Japan Special Ceramics MotoDX Plug CPR8EDX-9S 95321
Item Number
CPR8EDX-9S
Vehicles
GSX-R125 ( 2BJ-DL33B ) 2020
Number of man-hours
About 1 hour
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
I decided to buy it for power up and good starting performance.
Was the one you received as per Image?
It was as per Image. None in particular.
Was the installation difficult?
The GSX had to be removed from the exterior, so that's where the time was spent; the Plug requires the supplied tools.
How was your experience with it?
I didn't experience any more change than other car models. It was no different than I expected.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
I didn't feel any change in performance.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
I knew I wanted a Center Stand.
As expected, OEM Product View detail
METAL but not Snap.
I always thought it was Casting Iron because SV650 has a magnet on the Left Front Brake disc rotor, but when I looked up the magnet on the CB1000R, a high-end motorcycle I recently bought, I found that there is a magnetic stainless steel version, which I think is the one used in commercial motorcycle rotors. I think the motorcycle rotors are made of it. It is said that about 70% of general stainless steel is SUS304, and the 300 series is the most rust-resistant stainless steel without magnetism. I could not see much change in the pad. But it should have a good life span. View detail
Stainless rotor
The OEM Brake Pads I have used so far were replaced after 25000km and DAYTONA Red Pad after 10,000km. The exception is for Race. The exception is for Race. View detail
Dress-up??
I wanted Accent and I bought it.
I was torn between Gold and Red until the end,
The Engine part was Bronze, and it was Gold.
I think it was the right decision.
Self-sufficientParts, but I'm glad I got it.
View detail
CROSSCUB110/Mounted on JA60
CROSSCUB110 (JA60) The product has been installed in the
However, the supplied boltc. is M8 size, so it cannot be installed as it is.
The handlebar mounting bolt on the CROSS CUB is M6 size, so it will fit.
Bolt×2 pieces of M6 - Collar (Spacer) of M6×Quantity:2pc. Set is the minimum requirement. I bought it from Net mail order because it is not sold in Home center around here. I bought the M6 Washer×Quantity:2pc. Set was also used.
☆ Reference
M6 Bolt…M6 x 45mm Bolt With Hexagon Hole/Half-Screw
M6 color (Spacer) …13X6.2X15
M6 Washer is sold at home centers around the area.
It is not impossible to substitute the M6 collar (Spacer) with the M8 collar that comes with the product, but I bought the M6 one because it might be wobbly.
Quantity of the four Bolts at the Center of the Handlebar Mounting section in the front.:Remove and install the 2pc.
As shown in the photo, JA60 has almost no clearance between the Multi Bar and the Meter, so parts to be attached to the center of the Multi Bar may not be suitable or require some ingenuity.
View detail
Hey!
Contact Person!
I thought I sent you an email telling you to Cancel!
View detail
Fits: SUZUKI V-Strom 650, SUZUKI V-Strom 1000
Even if Size is past Limit….
The film is hard and fits in the MeterSize Limit. I managed to install the film, but after washing the car, the film started to float when I blew off the water droplets with a compressor.
I stuck it again, but I am not sure about its durability. Is the size still not right?
View detail
No functional problems, but ….
No functional problems, but the paint started cracking and peeling about a year after installation. There is a problem with the quality of the paint or the painting method. View detail
Is there a problem with being thinner than OEM?
I'm sorry I couldn't provide a photo, but when I used it on my NINJA2 Helmet 50RSL, I compared it with the OEM one, and the shaft part that holds the pad is clearly thinner,
The measurements were taken from the OEM, so they should be the same diameter." This was the case
I have a question for those who are familiar with Brake, is there any particular problem with the thin shaft part?
Has anyone who bought the same Stainless Steel Pad Pin had a similar case? I would like to hear your opinion. Thank you in advance.
View detail
Fits: KTM 1190ADVENTURE, KTM 1090ADVENTURE R, KTM 1090ADVENTURE, KAWASAKI Versys650, KAWASAKI Versys1000 SE, KAWASAKI Versys1000, HONDA VFR800X, KAWASAKI Versys-X250 TOURER, KAWASAKI Versys-X250, HONDA VFR1200X, HONDA NC750X, HONDA NC700X, HONDA CRF1100L Adventure Sports ES, HONDA CRF1100L, HONDA CRF1000L Adventure Sports, HONDA CRF1000L, HONDA 400X, DUCATI MULTISTRADA 1260, DUCATI MULTISTRADA 1200, BMW G310GS
It is Just size
I was able to use it normally with the OEMSIDEPannier installed. View detail
Useful for cold season commuting
[How is it used?
installed
Was the one you received as per Image?
Grip is Slim and good.
Was the installation difficult?
Left Side Grip is difficult to install. How do we get there?" I struggled with it for about 15 minutes. I hit it with a board and tapped it in with a plastic hammer, but the Motorcycle shop advised me not to do it as much as possible because it could be damaged.
How was your experience with it?
The product Single Body is warm, but it is even more effective if you use Knuckle guard, Cover, or other devices to protect it from the driving wind.
[Included Parts:were they on?
Everything was in place.
[Was there anything that disappointed you?
Sufficient performance is not a problem.
View detail
Improved starting performance! Certainly works!
I repurchased the commuter issue because I switched from CUB110JA44 to JA59.
I had used a Plug of this series in my previous car and liked the improved starting performance and the acceleration feeling at the beginning of Axel opening.
So I decided to remove it from JA44 and reuse it in JA59, which I had switched to, but to my surprise, the designated Plug heat value was changed to 6→8 for JA59, which became a New ModelEngine!
I wonder if it is the effect of the higher compression ratio of the Engine?
Anyway, now I can no longer reuse it, so I bought another MotoDXPlug, number 8.
The installed impression is the same this time, with the first immediate impression being improved starting performance.
The image that used to be played with a "curl" sound is now played with a "curl" sound, and the increased pulse and torque feeling at the beginning of Axel opening is also unchanged.
We do not yet know how long this performance will last, but the manufacturer claims that the durability has been improved, so we are looking forward to the Large model.
View detail
Reliable because it's DAYTONA.
I used it on my GSX1300R HAYABUSA.
The quality is quite good.
I bought this one because I thought it was not that expensive since it is Bar End.
View detail
More rust-resistant than OEM Product
I used this for an overhaul of a very old OEM Caliper. The previous owner had maintained it to some extent and it was not so badly worn, but I wanted to assemble it in a new and clean condition if I was going to overhaul it. I chose it because I wanted to assemble it in a brand new and clean condition. View detail
Peace of mind that it is made by MORIWAKI
The peace of mind of being made by MORIWAKI.
I don't have Level gauge, so I guess I'll go back to OEM just in case I need to replace Oil.
So far, no problems at all.
View detail
I use it every time.
I use it every time as it seems to work well with Aluminum drain bolt. View detail
Required for Northeast Number.
The grip is so thin and natural that you don't even notice it has been replaced. View detail
I am very grateful for this season!
My other car is equipped with a Grip Seater at Standard Equipment, and in the middle of winter, I have been benefiting from it, so I installed it on SecondMotorcycle as well.
As a result, WW could be a little warmer.
I guess the performance is a consideration for Battery capacity, etc., but if I had my wish, I would prefer a little more warmth...
The product looks and feels completely comfortable to hold.
Having said that, I have been able to spend this winter more comfortably than if I had nothing on!
View detail
Large satisfied
I have been asked by my daughter for a long time, but due to the severe cold weather this year, I bought it. (Scooter) So I had a hard time removing the cowl, but I am Large satisfied with the contents of the product. I have several other motorcycles, so I plan to purchase & install them one after another. I think it is very cost effective! View detail