Reviews
Perfect for dress-up!
The dress-up effect is great.
It also feels right in use.
View detail
Large cuttings that keep the oil level.
I used it for an OEMcarburetor overhaul. 。
Parts inside Carburetor.
To put it very simply, it is like a float that floats in a Pool filled with Gasoline called the Float Chamber at the bottom of the Carburetor.
What is a Float chamber?
Float chamber means Float room. 。
A container for holding a certain amount of fuel that flows from the Fuel Pump. 。
In order to supply the proper amount of fuel to the main nozzle where fuel is being sucked out, the system uses a Needle Valve and Float to keep the liquid level at a constant height.
The role of Carburetor's Float chamber.
The ‥Float chamber plays a role like a Pool that temporarily accumulates fuel in the carburetor.
Fuel accumulated in the float chamber is mixed with air through the Slow Jet and Main Jet, and finally supplied to the engine as air mixture.
How does Carburetor's Float formula work?
The Float system is one of the fuel supply methods, and the carburetor has a dedicated space for storing fuel such as Gasoline called Float chamber, and a unique shaped float called *Float is installed inside this Float chamber. 。 The movement of the Float then adjusts the amount of fuel flow out to provide fuel for the mixture.
Float = component changed this time.
Float, however, is in constant contact with gasoline, so it will deteriorate. Deterioration seems to be inevitable, not just a cause.
As the Float deteriorates, the buoyancy of the Float decreases.
What happens when Float's buoyancy decreases? ]
Float will deform and lose buoyancy if it is exposed to Gasoline for a long time and deteriorates.
The valve may not close with enough force to stop the gasoline from flowing into the fuel tank, causing the oil level to rise above the standard level.
→Overflow occurs.
On the other hand, if the oil level of the carburetor is too low due to deformation, etc., the oil level of the carburetor will be too low.
The fuel mixture is insufficient to meet the fuel requirements, resulting in symptoms such as a thin fuel mixture or, in extreme cases, the inability to start the engine.
Continuously low fuel level puts a continuous load on the engine, which may lead to a risk of engine blowout. 。 It can give more serious Damage than high oil level conditions and should be treated with caution.
In other words, Float is →.
The function of keeping the gasoline oil level in the float chamber of the carburetor constant and supplying fuel.
[Causes of Float Deterioration]
Trouble may occur if the Gasoline in the Chamber is altered or the Float itself is corroded due to decades of aging or prolonged neglect since its manufacture.
→ In my case, it's been over 20 years since manufacture. I think deterioration is undeniable.
It seems to me that replacement is desirable at some point, especially at Overhaul.
I immediately disassembled and replaced it, but the Float I took out was discolored brown (laugh).
If I keep using it like this, it's going to melt.
I'm glad I had the exchange.
Although there are few cases where only a Single Item is replaced, it is one of the parts that should be checked every time a Carburetor is overhauled.
View detail
Stable Explosive Power
Large cutting Plug that sends strong sparks flying.
Since we have installed Uotani SP2, PlugGap is spread out as specified.
This purchase is as a spare part.
View detail
Fits: DUCATI SCRAMBLERIcon, DUCATI 1299 Panigale., BMW R1200RS, BMW S1000RR, SUZUKI GSX-S1000, SUZUKI GSX-S125, SUZUKI GSX-S750, SUZUKI GSX1000S KATANA, SUZUKI GSX1300R HAYABUSA, SUZUKI GSX1400, SUZUKI GSX250R, SUZUKI ST250E Type, TRIUMPH STREETSCRAMBLER, SUZUKI VANVAN200, SUZUKI BANDIT1250, SUZUKI DL1000 V-STROM1000, SUZUKI DL1000 V-STROM250, SUZUKI GRASS TRACKER BIGBOY, SUZUKI DL1000 V-STROM650, SUZUKI Intruder Classic
Cute.
Pad thickness is just right and cute.
It would be better if it were cheaper.
View detail
Fits: KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR750, KAWASAKI Z2 (750RS), KAWASAKI Z1 (900SUPER4)
Mounted on kz900
I changed only the color of the bolt. I would like to change the exterior someday. View detail
Good cost performance, OEM same etc. Crimp structure is also safe.
Used to refresh a NORMAL rubber hose that had been used for nearly 40 years since new and had cracks on the surface.
The Crimp is made by NICHIRIN, the same company that makes the OEM Brake hose, and the connection to the banjo section is the same quality as the OEM Crimp.
We purchased this product because it is durable and reliable for long-term use, and it kills two birds with one stone:it also provides a Snap and BrakeTouch as a mesh hose.
Performance is fine.
After installation, the Crimp was not handling well for about a year, and it was pulling tight due to interference with the Cowl Bracket at full lock, but the Crimp did not pull out and the Hose did not break.
In order to reduce in cost and increase reliability, the panjo adapter is fixed and there are only two types of orientation, 90-degree right angle or parallel, for the upper and lower panjos, and only two types of banjo adapter angles, straight or 20 degrees, so you have to choose the type of car to install. The banjo adapter has only two angles, Straight or 20 degrees, so you have to choose the type of car you want to install it on.
View detail
The pictures are confusing.
I bought this for use on a 2023 SV650.
It's my fault for not checking carefully, but I saw two Levers in the sample product photo, so I decided to order a Quantity:Pair (for Left and Right) Quantity:I bought it thinking it was Pair.
When it arrives, it is only Brake lever.
I had no choice but to purchase an additional Clutch, but since it was not sold for the SV 650, I had no choice but to return it.
The product itself had a good texture, but the sample photos were confusing.
View detail
A little short, a little thick
I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people.
View detail
Purchased for a 12 year MODEL ninja 1000
This is the first time I have used this Drain Washer.
I used to use Drain Washer purchased from Motorcycle shop, but I bought it because I ran out of stock.
I don't think it's a problem since it's OEM, but just to be sure, check the area around the Drain Washer after test run after replacing the Oil.
It didn't leak, so it's Large sturdy.
OEMs are secure.
View detail
Small
I bought it for my BMW R1150GS because it fits VST 1050, but it is smaller than I expected. I bought it knowing that it would not fit over the SIDEPannier, but I did not expect that it would not fit over the Top case either. The storage is compact. View detail
With reference to your Impression.
I bought one from this Manufacturer based on your Impression. View detail
Affordable and easy to use
[How is it used?
Wiring was needed for Circuit Running.
Was the installation difficult?
Copper Washer is included, so there is no need to buy it separately for the first time.
Of course, without the WiringPlate, wiring is not possible, so please purchase and install it separately.
6R is Oil Pan Bolt with Plate bite.
I was reluctant to remove the oil pan bolt, but so far there has been no oil seepage, so I can use it without any problem.
How was your experience with it?
Designability is not particular, but I have no problem with the functionality.
Affordable and easy to use.
[Included Parts:were they on?
Copper Washer and Wire included.
It is a one-time fee and must be purchased the next time it is used.
Point and hang of installation
Wiring should be done by applying tension in the direction that the bolt is tightened. Sometimes we see wiring that is not only meaningless but also dangerous.
View detail
I have no particular problem using it.
It is a consumable item that is used for a short period of time, so it is very helpful to be able to purchase it at a reasonable price. I have no problem using it. View detail
Best Match for Good Position XSR125.
The handlebar on my XSR125 did not fit and my shoulder stiffness got worse after the first ride, so I replaced it with this handlebar based on Net information.
I also bought a Flat continental2 type and compared it with the BMConti3 type while temporarily attaching it, and found that the BMConti3 type fit better.
It's so easy to ride that I think this should be the standard now! It is so easy to ride. I recommend it.
I had prepared a riser, but I am 175cm tall and it is just right without the riser.
Small patterned person is Quantity:SetBackRiser would be a good position.
Drilling is required, but a drill driver is sufficient for this purpose as long as the position is marked temporarily and the punch is firmly applied.
It is hang to go little by little while checking, not trying to open it all at once.
It was a good buy for the XSR125.
View detail
Looks good.
I chose it for its durability, but the durability is yet to be determined. View detail
Fits: KAWASAKI ER-5, KAWASAKI GPX600R, KAWASAKI KLE500, KAWASAKI KLF220, KAWASAKI Eliminator 600, MAGNI 1000 Australia2, MOTOGUZZI 1000 Ditna RS, bimota YB-4, bimota YB-6, bimota Dietsch 1000, bimota Flannel 1000, HONDA CB1100F, HONDA CB1100R, KAWASAKI 1000GTR, KAWASAKI 250TR, KAWASAKI EN400, KAWASAKI EN500, KAWASAKI EX-4, KAWASAKI FX400R, KAWASAKI GPZ1000RX
Idling stabilized?
I changed the oil as part of maintenance, and it seems to have stabilized the idling, but I don't feel that the power is increased. I really don't know if the period to change the oil was too short and the oil was not so deteriorated, but it is an old motorcycle and I will replace the oil as soon as possible. Next time I will buy a Torque wrench and tighten it with the specified Torque. View detail
Fits: SUZUKI GSX-R1100, SUZUKI GSX-R750, HONDA CB1000 SF, HONDA CB400SF, HONDA X4, HONDA CBR1100XX SUPERBLACKBIRD [Super Blackbird]., HONDA CBR900RR FIRE BLADE [Fireblade]., YAMAHA XJR1300, YAMAHA XJR1200, YAMAHA XJR400, YAMAHA FJ1200, YAMAHA FJ1100, YAMAHA XS1100, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX250, SUZUKI GS1000, SUZUKI GS750, SUZUKI GSX1100, SUZUKI GSX750
Just cover it!
Funnel is bad for the engine and does not pass vehicle inspections. The RAMAIRSystem is a simple system that can be installed on the engine, and it is easier to remove than the Power Filter, so if you want to change to a funnel, you can easily remove it. View detail
Aftermarket parts are well stocked, so there is a sense of security.
I think it is semi-floating, so it should be reasonably durable, but even in case of emergency, it is helpful that all the parts can be purchased at Repair Parts. 。
I am currently using a Brembo caliper with no problems.
Comparison with bremboRotor purchased at the same time.
View detail
I think Design is number 1.
I was worried about OEM, but the price was the same, so I went with SUNSTAR.
PremiumRACING is a great way to create your own combination!
There are various manufacturers, but I think Design is the best.
View detail
To match the Gold amount up to free shipping.
As per Title, I bought it to get free shipping.
We strictly follow the routine of one in every two Oil changes, so this is fine.
This one also has an O-ring attached, which is convenient.
There were two types of large O-rings in the package. I used the one with the smaller diameter wire, but I think it is fine.
Is it because of these two types of O-rings that I feel like there are so many compatible car models listed?
A certain "Kansai Soul", which is only cheap, is poorly made, but I think this one can be used with peace of mind.
View detail