Reviews
Titaniumium color!
Small but finely crafted
Luxury that you can feel in your hands
Worth the Gold!
View detail
Fits: HONDA CRF1000L, HONDA CRF1100L AFRICA TWIN, HONDA CRF1100L AFRICA TWIN ADV SPORTS ES, HONDA CRF1100L AFRICA TWIN ADV SPORTS ES DCT, HONDA CRF1100L AFRICA TWIN DCT, HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250R, HONDA CRF250RALLY, HONDA CRF250RALLY(S), HONDA CRM250AR, HONDA CT125, HONDA TRAIL125, HONDA TRX450RX, KAWASAKI D-TRACKER X, KAWASAKI VERSYS1000, KAWASAKI VERSYS1000SE, KAWASAKI VERSYS650, SUZUKI V-STORM1000
I still feel safer with the Bolt stop.
OEM Cap." Than Screw bolt." looks better. It also provides some Prank protection. I also put a Plastic bolt cap on mine.
It goes on the 2023 CRF250RLY50MD47 with no problem.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA YZ125, YAMAHA YZ250X, YAMAHA YZ450F, YAMAHA YZ450FX
Purchased White for Decal paste
I bought White to match Decal. 。 The OEM YAMAHA Logo has a convex shape, but this one is plain and can be applied cleanly.
Relief shape other than Logo and others are similar to OEM!
The OEM did not think anything of it.
It goes on easily, but I wonder if the Body of this one is slightly deformed.
Hole position did not match Exactly.
Screw one of the first three holes at the end, and the other holes are used for the Body.
The holes were aligned as if they were pushed in or aligned with each other, and the screws were inserted into the holes without any problem.
Be careful not to insert the screw into the gapped hole by force, as it will enter the screw at an angle and damage the screw threads on the fork side.
There is no distortion after installation, and the gap between the Fork and the Fork has been properly taken care of.
View detail
There was no one with Level gauge.
The OEM Product was not strong enough, so it was replaced. After installation, I found that the flange surface is narrower than the OEM Product, so there is a gap between the OEM Product and the engine side. I would have liked to have had a product that fits Exactly. View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Fits: YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250F, YAMAHA YZ400F, YAMAHA YZ450F, YAMAHA YZ450FX, YAMAHA YZ250FX
Easy to apply Decal without YAMAHA's stamp
When applying Decal, OEMGuard has a raised YAMAHA imprint, and I bought it because I thought Decal would peel off easily.
It looks good, installs well, and is durable enough when used. No complaints, no excessive interference with the Fork outerTube, and the Decal was easy to put up.
View detail
It was EXACTLY!
I purchased this to replace an OEM Oil cap groove that was broken.
It was Exactly in JA10!
View detail
I should have bought it earlier.
Clutch control is very easy, and above all, the in-gear kick is almost a one-shot instruction!
I would definitely recommend anyone doing HED with 250X!
View detail
Genuine DID 520ERVT Replacement Chain Link
I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERVT is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. I keep the rivet link type and this clip joint type but had ran out of this version, hence the purchase. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
it works.Never seen such a strong spark
I've run NGK in all of my bikes for years and never have had any issues and definitely get great performance. I won't run anything else in my bikes and have never experienced failure from them. If they are changed at their recommended interval or even a little early you'll be hard pressed to find anything better. Always be sure to set your gap for what your machine manufacturer recommends and you'll be in great shape.There are NGK fake spark plugs on the market. You need to be careful.Buy from Webike or distributors. View detail
TZr50R Oil Filler Cap O-ring
[How is it used?
Used for EngineO/H of YAMAHA/TZr50R.
This item is an O-ring of Oil Filler Cap.
It is not a part that needs to be replaced, but we replaced it because it was a good opportunity to do so.
How was your experience with it?
OEM parts are the only choice for engine parts. There is no problem with quality.
I compared it with the old O-ring, but the old one was still hardened.
Oil does not leak from this area, but does it affect the pressure application?
How did it compare to other products?
There is no Other Brand Product, so there is no comparison. Even if there were, OEM would be the only choice.
[Points to note]
I installed it while taking care not to twist it during installation.
Grease is also applied just in case.
View detail
Oil Filler Cap
Changed to Green Light or Gold. View detail
I'm too weak.
It was distorted when I fell and hit it.
With OEM, this didn't happen even if you hit it hard..,
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250
In preparation for
Quantity to add Bar End:Exchange in Set
The Bar End for the Close type used in the past is said to have been discontinued, and the Open endSpec. Bar End was purchased.
There is no particular change in the feel of the Teflon treatment, but it is a good idea to have multiple Teflon coated parts because they are easily damaged in the event of a fall or other accident.
The price is also relatively inexpensive.
View detail
Z -WHEEL Aluminum nipples kx250 Front
Cost performance is better than OEM.
Nipple head (Rim side) is huge, so
Large amount of pop out from Rim
When installing the Tire, the BEET was not falling enough.
Tire is a little hard to fit
View detail
For CB250F
.Actually this item i could not found in my country (VX Series Joint Link 520VX3). Finally I bought it from webike. It is original. Very good packaging.fast shipping.I am happy to deal with the webike team View detail
Fits: HONDA CRF450R, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250FX, YAMAHA YZ450FX, KAWASAKI KX450F
Required equipment for YZ
CYCRA Disc Covers and Quantities:Used in Set.
YZ is required for Enduro because of the weakness of the thinness of the Front fork abyss
Fixation is done by biting into the hollow of the Fork, then occupying the Screw to fix the Quantity:Pair (for Left and Right) The method is to spread out the screw to the "smallest" possible size, but this screw is a tricky one and very small.
Licking is very difficult to remove.
When removing the Screw, even if it is a hassle, it is necessary to clean the area around the Screw and make sure that the Wrench can be inserted securely.
Size-wise, it is unavoidable, but this is the only point to note.
View detail
Fits: YAMAHA YZ450F, YAMAHA YZ250X, YAMAHA YZ250F, YAMAHA YZ250, YAMAHA YZ125X, YAMAHA YZ125, YAMAHA WR450F, YAMAHA WR250F
You can't go wrong if you choose this one.
Guard focused solely on disc protection
I tried to use a disk guard to protect the fork bottom when I renewed my vehicle, but due to the difficulty of installation and accuracy, I returned to this one that I had used before.
Refreshing around the disc and fork bottom by inserting the Mount instead of the Brake Side Collar and fixing it in place.
Refreshing condition is good because it is a place that gets covered with mud and it is hard to clog up with mud.
View detail
Genuine Yamaha Front Wheel Oil Seal for WF450F 2017
This was the oil seal for the front wheel on the WRF450F which needed new wheel bearings. I do always replace the oil seals when it comes to any bearings where possible for my own peace of mind. It just makes sense to do this. Finding the right oil seal was easy as I already had the schematic open for the wheel bearings anyway. The price for the new seals was great value. At this price is was silly not to get them. With the other parts needed for this replacement, I had all the order shipped using EMS which are my chosen and trusted courier. My order arrived in 100% perfect condition in 5 days from being shipped. The oil seals came in th standard Yamaha packets and were also inside a nicely made bubble wrap envelope by Webike warehouse to keep them safe. The oil seals are pretty rigid if I am honest but that is not a bad thing. They are top quality oil seals which you expect from such a well respected manufacturer like Yamaha. With a tiny bit of oil to seat them easily, the job was complete and now the front wheel moves freely and smoothly as it should. Great job guys, very pleased with this purchase. View detail
Fits: YAMAHA RZ250, YAMAHA RZ250R, YAMAHA RZ350, YAMAHA YZ450F, YAMAHA RZ350R, YAMAHA SR400, YAMAHA SR500, YAMAHA WR450F, YAMAHA XTZ-750XTZ750 SUPERTENERE, YAMAHA YZ250, YAMAHA YZ250X
Have you become snappier?
[How is it used?
I bought it because I use Enduro as my main and use Clutch a lot for logs and gullies.
Was the one you received as per Image?
It is exactly as shown in the Image. I even feel that it is packed more Compact than I expected.
Was the installation difficult?
Simply replace the existing clutch spring that is holding it in place, and if you work with the motorcycle on its side, you don't even need to pull the oil out. You just need to make sure that the spring is properly seated in the Retainer groove.
How was your experience with it?
Since the last time I rode the Washer, there was a little bit of free time, so I could not say that there was a drastic change! I used only one washer, so I may add another washer to change the characteristics a little more.
[Included Parts:were they on?
The bolt has a countersunk hole to reduce friction and a hexagonal head. The torque is 10Nm, but if you do not have a hexagonal tool, you will have to tighten the bolt by feel.
[Was there anything that disappointed you?
No, it is not. This time the test was at low speeds, so I am looking forward to seeing what happens at high speeds.
View detail