Reviews
Exactly to MOTARD as well.
Bought this for my drz400. For a long time, I had been wearing the one for my previous Large Motorcycle, but it was not so good because it was too loose. This time I bought it because it said "for Off-Road" and I am satisfied with the just fit. I also like that the lower part can be closed with a string. View detail
Fits: YAMAHA SR250, SUZUKI 250SB, HONDA 250T LACustom, HONDA AX-1, HONDA CL135, HONDA CL350, HONDA CL72, HONDA CL77, HONDA CM250T, HONDA CM400T, HONDA CRM250AR, HONDA CRM250R, HONDA FTR223D, HONDA FTR250, HONDA GB250 CLUBMAN, HONDA GB400TT, HONDA GB500TT, HONDA MT250ELSINORE, HONDA MTX125R, HONDA MTX200R
Does not fit the KL250 Sherpa.
The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.
KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.
If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.
Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!
I bought it + even processed it so I'll be using it for a while lol.
View detail
Z -WHEEL Aluminum nipples kx250 Front
Cost performance is better than OEM.
Nipple head (Rim side) is huge, so
Large amount of pop out from Rim
When installing the Tire, the BEET was not falling enough.
Tire is a little hard to fit
View detail
Plug
I put One set on the back tool box. I bought more than one set because they are one lung or cover. The quality is good! View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
CB250R installed.
I installed it on my CB250R. Affordable and easy to see.
It's just right because it doesn't stick in the Motorcycle seat.
View detail
NTB if there is NTB
If high performance and quality are not required, NTB tends to be cheaper than OEM for consumable parts.
Thank you for your continued support!
View detail
The ball joint could be a little stiffer from the start….
The price and designability are excellent, so Cost performance is high, although I personally like it,
The ball joint at the base of the mirror was shipped very loose, and although a special tightening bracket was included in the package, it was difficult for me, a clumsy amateur, to retighten it.
(I had the shop do it for me since it was also in conjunction with the Handlebar replacement …)
View detail
Purchased due to Headlight Bulb running out
I purchased these because the bulbs were out. The Pine Stripe bulbs were as bright as I expected.
It's also inexpensive, so it's helpful.
View detail
It looks better now.
I put it on because it stands out from the OEM. View detail
Good variety of color variations
Standard NGKPower cable, used for CUB.
Speaking of NGK, I had always thought of Red and BlueCable images, but I was surprised to find that NGK has a wide variety of color variations.
I was curious about the Yellow color code + BlackCap, so I bought it, and the actual color was a nice bi-Bit color as well.
View detail
I appreciate the affordable price.
[How is it used?
The KDX220 I purchased used was not in bad condition for an old vehicle from the 1990s, but the seat cover was in a slippery condition because the surface had begun to harden, probably because it was from that era.
On the way home after taking delivery of the car at Motorcycle shop, my buttocks moved back and forth every time I accelerated or decelerated, making it very difficult to enjoy the ride, and as soon as I started driving. The first custom was to reupholster the Seat Cover. It was like that.
Originally, I was going to bLOOVE it, including a look at the vehicle, but I went home right away and looked at Webike's product introduction section. KDX220 Seat I've been searching for...
Since it is an old vehicle, there are not many choices, but I-Net's Off-road Vehicle UniversalSeat Cover was a hit, and the price is low! If by some chance I fail, I'm ready to give up." So I bought it
How did you like it?
As a universal product, it is not as good as the Seat fabric made by a three-dimensional manufacturing process for each car model, but I personally think that the KDX Seat itself is not a complicated shape, so I was able to stretch it well.
The new fabric is highly flexible and the dimpled finish gives it a high grip, so you can enjoy riding without being carried back and forth every time you accelerate or decelerate.
To be honest, I wanted to stick with the OEMSeat Cover, but after looking at the price, the thickness of the fabric, and the condition of the finished product, I felt this product was sufficient.
How did it compare to other products?
There are few choices in terms of car models to begin with, and other products are expensive and have stopper belts sewn into the seat surface. I mean it!" I couldn't choose one because I had a strong feeling that it would be embarrassing to me, as I have poor driving skills.
What points should I pay attention to?
Patience and ingenuity are required because the products are not three-dimensionally sewn for car models.
If the tucker is driven in too shallow, there is a risk that the fabric will break from the tucker.
Front and back of the Seat are loosely secured to the Quantity:Pair (for Left and Right) When pasting the "Beauty" sponge, it should be pasted along the "Seat sponge" without wrinkles to make it beautiful.
Other items that would be helpful
The deciding factor in the purchase
The only Seat fabric that was safe for normal use was sold only by iNet.
We were not able to confirm that the products were made by KawasakiOEM, so we did not consider them in this case.
[How is it used?
Basically, it's Main for city driving. I can't even use SEROW, so it was too Hurdle for me to play in the mountains with a 2CycleEngine equipped car.
【Included Parts:presence or absence】.
Seat CoverQuantity:1pc. with Instruction Manual and Vinyl for waterproof.:Set
Tandem belt is not included, so those who need it must purchase it separately or reuse the OEMBelt.
[ITEMS TO BUY TOGETHER
Seat fabric to fasten to Seat Base seat. Tucker. and short-legged core.
It may not be necessary for those who apply Vinyl underneath, but for those who apply directly to Sponge without Vinyl, it is better to prepare SiliconCoking agent to be applied to the reverse side seam of the Seat fabric.
Opinions and requests to Manufacturer.
Although it may not be a problem for popular cars, it is a product that older cars and minors cannot do without, so we hope you will continue to sell Lineup for a long time.
View detail
Is there a problem with being thinner than OEM?
I'm sorry I couldn't provide a photo, but when I used it on my NINJA2 Helmet 50RSL, I compared it with the OEM one, and the shaft part that holds the pad is clearly thinner,
The measurements were taken from the OEM, so they should be the same diameter." This was the case
I have a question for those who are familiar with Brake, is there any particular problem with the thin shaft part?
Has anyone who bought the same Stainless Steel Pad Pin had a similar case? I would like to hear your opinion. Thank you in advance.
View detail
Useful for cold season commuting
[How is it used?
installed
Was the one you received as per Image?
Grip is Slim and good.
Was the installation difficult?
Left Side Grip is difficult to install. How do we get there?" I struggled with it for about 15 minutes. I hit it with a board and tapped it in with a plastic hammer, but the Motorcycle shop advised me not to do it as much as possible because it could be damaged.
How was your experience with it?
The product Single Body is warm, but it is even more effective if you use Knuckle guard, Cover, or other devices to protect it from the driving wind.
[Included Parts:were they on?
Everything was in place.
[Was there anything that disappointed you?
Sufficient performance is not a problem.
View detail
More rust-resistant than OEM Product
I used this for an overhaul of a very old OEM Caliper. The previous owner had maintained it to some extent and it was not so badly worn, but I wanted to assemble it in a new and clean condition if I was going to overhaul it. I chose it because I wanted to assemble it in a brand new and clean condition. View detail
Required for Northeast Number.
The grip is so thin and natural that you don't even notice it has been replaced. View detail
I am very grateful for this season!
My other car is equipped with a Grip Seater at Standard Equipment, and in the middle of winter, I have been benefiting from it, so I installed it on SecondMotorcycle as well.
As a result, WW could be a little warmer.
I guess the performance is a consideration for Battery capacity, etc., but if I had my wish, I would prefer a little more warmth...
The product looks and feels completely comfortable to hold.
Having said that, I have been able to spend this winter more comfortably than if I had nothing on!
View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
quite good shape
Mirror was rusted out and replaced with a more recent form.
The navigation is easy to see and the design of the Mirror makes the vehicle feel like it has been exposed.
There is no runout when driving.
View detail
Fits: YAMAHA SEROW250, YAMAHA XG250 TRICKER, YAMAHA DT230 LANZA (DT230), YAMAHA WR250X, YAMAHA SEROW225, YAMAHA WR250R
It looks like a certain Manufacturer's product...
[How is it used?
I purchased this product during the Restore of SEROW225 WE and it was a Timing Well Sale item at Webike, so I was able to save even more than usual.
However, the price of the product is not that of a certain D0C product in the first place. Pi0t Lever CP." Quantity in Gold amount for One Side:Pair (for Left and Right) The product is originally Reasonable because it is sold at a price so low that it can be purchased by
They look very similar and to a stranger. It's wearing an expensive-looking lever of the billet type." It can create a sense of
How did you like it?
It is not clear if it is as rigid as the original, but it also has the same Pivot function, which makes it difficult for the lever to break even if it falls over slightly.
My SEROW is Material:The aluminum handlebar guard is also a factor in reducing lever breakage, but for amateur mountain play, the difference between the original product and the new one is almost unnoticeable. (Incidentally, the SEROW250 I bought used had the original Lever installed from the beginning.) 。
How did it compare to other products?
I have used this product and the original DR0 pipod Lever, and as I mentioned above, it is so well made that you can't tell unless you are told in Large roughly.
The Nylon washer-like material used in the bolt that adjusts the grip is weak and easily crushed, making it difficult to adjust, but the others parts are as good as the original product.
I have not checked the strength of both products because it would be a waste, but both products have been used without damage under similar conditions.
[Points to note]
As mentioned above, the only thing to do is to tighten the Bolt moderately to adjust the grip.
Grease up each moving part and joint thoroughly.
Other items that would be helpful
The deciding factor in the purchase
Made by 0RC Pi0t Lever CP." Because the price is less than half of the price of a Levar that looks like a Levar.
【Included Parts:presence or absence】.
Quantity of Brake lever and Clutch lever:Pair (for Left and Right) There are no other Included Parts:.
[ITEMS TO BUY TOGETHER
Although it is cheaper than the original product, it still costs 6,000 yen, so if you attach a sturdy Handlebar Guard, it will protect not only your lever but also your hand in case of a fall, so you can feel even safer.
Opinions and requests to Manufacturer.
From now on. It's ____-ish." Please take care of our products at Reasonable prices.
[Points to note]
As mentioned above, the only thing to do is to tighten the Bolt moderately to adjust the grip.
Grease up each moving part and joint thoroughly.
Other items that would be helpful
The deciding factor in the purchase
Made by 0RC Pi0t Lever CP." Because the price is less than half of the price of a Levar that looks like a Levar.
【Included Parts:presence or absence】.
Quantity of Brake lever and Clutch lever:Pair (for Left and Right) There are no other Included Parts:.
[ITEMS TO BUY TOGETHER
Although it is cheaper than the original product, it still costs 6,000 yen, so if you attach a sturdy Handlebar Guard, it will protect not only your lever but also your hand in case of a fall, so you can feel even safer.
Opinions and requests to Manufacturer.
From now on. It's ____-ish." Please take care of our products at Reasonable prices.
View detail
Fits: KAWASAKI KX60, KAWASAKI KX65, KAWASAKI KX80/II, KAWASAKI KX85, YAMAHA Lanza (DT230), YAMAHA TT-R125, YAMAHA TW200, YAMAHA CELLOW 225, YAMAHA XT250X, YAMAHA YZ80, YAMAHA YZ85, YAMAHA Cerro 250, YAMAHA tricker
Rigidity is as expected
The texture and rigidity are both good. The handlebar brace is almost invisible (laugh). View detail
Water pump pliers
Even a light press-fit clip can DID be tricky, requiring a press-fit of the plate to create a groove to stop the clip. A cheap chain tool often fails to press-fit the clips properly. If you use a water pump pliers to tighten the 6mm nut to the plate with force, you can get a groove for the clip. I do not want to buy a Stripele for my own use, considering the frequency of use. View detail