Reviews
Fits: HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CT110 HUNTER CUB125, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB C125, HONDA Dio 110, HONDA LEAD 125, HONDA PCX 125, HONDA PCX 160, HONDA PCX ELECTRIC, HONDA ADV 150, HONDA HORNET250, HONDA HORNET600, HONDA CB 125R, HONDA CB 250R, HONDA CBR 250RR, HONDA CBR 600RR
Easy to hang and wind resistant. Very good.
I use this Repeater on my CT110 HUNTER CUB and GB250 CLUBMAN. It is my favorite.
I bought it last year when I bought a CT110 HUNTER CUB, because I was planning to add a front carrier and a RODCarrier to it. I am sure it will be a good reference for those who are considering purchasing it.
The front carrier is made of DRC, the largest class, and is fixed at the most forward position, so the front of the handlebar is considerably longer than in NORMAL, The height of the LeftFront section of the Rear Carrier is 10cm higher than the Seat. The lower part of the front wheel and Quantity:Pair (for Left and Right) As you can see in the photo, I can close the RearFastener to the very bottom, even with the bottom rope tightened quite a bit. I live in an area that is occasionally exposed to strong winds, and the Seat has never rolled up.
Also, I have been using it for over a year now and it has not deteriorated much. (There is a short period of time when the parking Space is in direct sunlight.) Not much dirt on it. (It has a roof, so it is virtually dry even in the rain.) and I have never washed the surface with water. I am very satisfied.
I bought it for GB250 CLUBMAN almost one year after CT110 HUNTER CUB. It is rather a little bit large, so the front wheel lower part and the quantity of the front wheel are a little bit smaller than the original size.:Pair (for Left and Right) The Adjuster rope at the bottom is fully squeezed. There is still room to spare, but not so much that it will flip up in the wind, so we are not worried at all.
Perhaps if it were exposed to rain and direct sunlight throughout the day, the evaluation of deterioration might change, but I cannot comment on that.
View detail
Nice...
I replaced it with a Sintered pad because the Brake squeal would not go away and it was less expensive and seemed more durable.
The pad before replacement came with an unknown manufacturer, so there is no comparison, but it works and does not squeal as usual. 。
Control is much better than I expected, and the effectiveness changes with the amount of force.
It seems to be a bit aggressive to Rotor, which is a concern, but it was a good decision to replace it.
View detail
Replace Red with Golden Pad
I have not been able to drive yet because of the rain, but I changed the pad as well as the Caliper OH!
I'm looking forward to running it. ('∀ `)
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja650, Others , HONDA VTR1000 SP1, HONDA VTR1000 SP2, HONDA VFR800, HONDA VTR250, HONDA RVF400, HONDA VFR750R, HONDA NC700X, HONDA NC750, HONDA GB350S, HONDA NC700S, HONDA CBR1000RR-R SP, HONDA CBR929RR, HONDA CBR1000RR, HONDA CBR1000RR-R, HONDA CBR650R, HONDA CB650F, HONDA CB650R
It is not a pure Black.
The color looks a little brownish rather than black in the right light. It is super easy to install. I think you can install it by yourself, but if you don't have the knowledge to remove the OEM bar end, you might want to ask a shop to do it for you. The included Inner Weight is a few Grams lighter than the OEM. View detail
It was EXACTLY!
I purchased this to replace an OEM Oil cap groove that was broken.
It was Exactly in JA10!
View detail
a titanium anchor
I bought it to wear a Guardian bell I'm afraid it'll rip because it's thin, but trust it because it's titanium! It looks good to mount the bolt anywhere under the bike. View detail
Fits: HONDA CBR400 R, HONDA GOLD WING, HONDA VTR1000, HONDA NC750S, HONDA NC750X, HONDA NC700X, HONDA DN-01, HONDA NC700S, HONDA VT1300CX, HONDA SHADOW400, HONDA SHADOW600, HONDA CTX700, HONDA INTEGEA, HONDA FORZA, HONDA Silver wing400, HONDA VTX1800, HONDA VTX1300, HONDA GOLD WING F6B, HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF
I installed it in the CB 750
I have been replacing the Oil Filter every two Oil changes because it is air-cooled and has been for years and I want to drive it for a long time. Installation is easy. View detail
![PREMIUM ZONE Oil Filler Cap [M20XP2.5]](https://img.webike-cdn.net/catalogue/images/15651/91887_O01_TS.jpg)
As expected of DAYTONA
Was the installation difficult?
pimping
How was your experience with it?
It's going to look different
View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
Posh indicator lenses
Very well packaged and very good quality lenses. The lenses took five minutes to fit and look great they are not too dark and you can see the orange bulb when illuminated View detail
Parenthesis good & easy to slip through
Mirror like insect antennae of Ninja1000sx when slipping through,
It seems to hit the car's expensive Side-view mirror and is in the way.
Replaced within a week of buying Motorcycle.
Up and down Quantity:Pair (for Left and Right) The camera can be moved to a wide angle, so it is good to have flexibility. wide angle.
However, is it Reduction in cost or Bolt is all Color:Unpainted…
I painted it Black because it floats around from Body.
It's a little hard to see, but Parenthesis is better, and overall I am satisfied.
PS:I'm surprised that Motorcycle with Cowl these days is not mommy to Mirror exchange too!
View detail
Reliable K-PIT
Repair Parts at KPIT for your peace of mind.
Purchased to replace Rotor.
View detail
It went well.
I knew it was Honda and For SUZUKI, but I bought it thinking it would come on if I changed Washer, etc.
The chrome black color looks great and the weight is expected to reduce vibration.
View detail
License Plate bend prevention
Before I installed the License Plate Base, I used to catch my pants and bend them, but since I installed the License Plate Base, I haven't had any problems. View detail
![PREMIUM ZONE Oil Filler Cap [M20XP2.5]](https://img.webike-cdn.net/catalogue/images/15651/91889_O01_TS.jpg)
Dress-up in a casual way
It can be dressed up casually.
I am satisfied with the quality of the product.
It would be better if it were a little cheaper.
View detail
Good texture
I bought it because I liked the texture and design.
The moving part is fixed by Bolt, so it could be loosened by vibration, and it was necessary to carry a tool at all times. In windy conditions, the Motorcycle Cover could push it loose.
I don't put much force on the Arm Up, so the Right Arm was hard to Gap. I also used the seat Gold, but it did not improve much. I don't think it was loose due to weak tightening.
Visibility would depend on the compatibility of the Motorcycle, but I could not see directly behind me on the FAZER.
It is a Cool product and should be used well together.
View detail
Cool! Good quality!
Attached to CBR400R 2024 model.
Cool! Best quality.
Just a little Gap?
I decided not to worry about Small things...
View detail
Reliable OEM Product
[How is it used?
I bought a used CBR600RR PC40 and after riding it for over 2 years, I decided it was time to replace it, so I looked at the Parts List.
How was your experience with it?
The fit is perfect and secure.
Since it was the first replacement, we removed most of the cowls and tank covers and accessed the air cleaner box.
Remove the Screw of the Air Cleaner BOX, and then remove the Quantity of the Air cleaner element.:Remove the 2pc Screws. Be careful not to drop them into the Throttle body at that time.
All I had to do was replace it by following the same procedure. It was my first time working with Smooth, but I was able to replace it with Smooth using only information from Net.
However, after 2 years and 10,000 km, the air cleaner was not too dirty before replacement.
How did it compare to other products?
[Points to note]
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
CBR600RROEM Product
[How is it used?
Since it is used as OEMPlug for CBR600RR PC40, we purchased the same one as regular maintenance.
How was your experience with it?
I found out on the Net that the replacement is done by removing up to the side cowl, unfastening the radiator, and replacing it, which I almost did, but I could not replace number 2 and 3, so I had them replaced at the Shop from WebikePit inService.
We were taught the same way at Shop.
As for the feeling of use, I have only ridden a few kilometers immediately after the replacement, but I am glad that I replaced it because I feel it has become Smooth.
The Plugs were used for about 8,000 km before replacement, but they all looked fine with a clean burn.
How did it compare to other products?
[Points to note]
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
CB650R spark plug replacement
cb650r spark plug replacement work
Even though the bike is difficult to work on, I feel good after replacing it.
It fits well. Due to the nature of the bike, you will need a lot of tools.
I'm proud of the self-exchange.
I don't know when the next time will be, but I will buy it then too.
I think it says to write 100 characters, but um... I don't have anything else to write.
-------------------------------------------------- -------- cb650r spark plug replacement work Even though the bike is difficult to work on, I feel good after replacing it. It fits well. Due to the nature of the bike, you will need a lot of tools. I'm proud of the self-exchange. I don't know when the next time will be, but I will buy it then too. I think it says to write 100 characters, but um... I don't have anything else to write. Powered by Google Translator
View detail