Reviews
![[Stock Lever] Brake Master Cylinder Kit [Horizontal Type 5/8" / Tank Separate Body Type]](https://img.webike-cdn.net/catalogue/images/105373/61738_TS.jpg)
Perfect for dress-up!
The dress-up effect is great.
It also feels right in use.
View detail
Vibration improvement at high speed
I purchased the Black color and it blends in well with the Grip. Installation was easy. I have not applied Screw lock yet, but I will do so after purchasing it at a later date. I was worried about the other company's HeBeaverWeight, but I am glad I chose this one. I have been driving at high speeds for about 30 minutes and my palms are no longer numb from the vibration at 6000 RPM. I wish I had bought it earlier. View detail
Yellow-colored areas fall off considerably.
I had no problem with the fit since it is the same size as the manufacturerOEM, but the yellow-colored part on the back of the sponge is falling off. But the yellow-colored part on the back of the sponge is falling off.
I have a feeling that if Carburetor sucks this in, it will clog up, so I will not use it and buy OEM.
View detail
The pictures are confusing.
I bought this for use on a 2023 SV650.
It's my fault for not checking carefully, but I saw two Levers in the sample product photo, so I decided to order a Quantity:Pair (for Left and Right) Quantity:I bought it thinking it was Pair.
When it arrives, it is only Brake lever.
I had no choice but to purchase an additional Clutch, but since it was not sold for the SV 650, I had no choice but to return it.
The product itself had a good texture, but the sample photos were confusing.
View detail
A little short, a little thick
I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people.
View detail
![Gasket，12X22X2 [92065097]](https://img.webike-cdn.net/catalogue/images/129465/92065-097_TS.jpg)
Purchased for a 12 year MODEL ninja 1000
This is the first time I have used this Drain Washer.
I used to use Drain Washer purchased from Motorcycle shop, but I bought it because I ran out of stock.
I don't think it's a problem since it's OEM, but just to be sure, check the area around the Drain Washer after test run after replacing the Oil.
It didn't leak, so it's Large sturdy.
OEMs are secure.
View detail
![Compact half cover [large]](https://img.webike-cdn.net/catalogue/images/91554/22144_TS.jpg)
Small
I bought it for my BMW R1150GS because it fits VST 1050, but it is smaller than I expected. I bought it knowing that it would not fit over the SIDEPannier, but I did not expect that it would not fit over the Top case either. The storage is compact. View detail
I replace them regularly.
This is a small component, but it is a large component that holds Brake Pads.
Rust-resistant Stainless Steel is easy to maintain.
View detail
![MCP High Spec Bike Cover《Bike Guard》 [LL]](https://img.webike-cdn.net/catalogue/images/43895/MBC005_01_TS.jpg)
Fits: BMW K1300 S, BMW F800 S, BMW K1300 R, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA XSR900, YAMAHA YZF-R1, YAMAHA YZF-R250, YAMAHA YZF-R3, YAMAHA YZF-R6, HONDA CBR650 F, HONDA CTX700, HONDA CTX700 N, HONDA NC700 S, HONDA NC700 X, HONDA NC750 X, HONDA NC750 S, HONDA PS250, HONDA VARADERO 125, HONDA VFR1200 F
I like the texture.
CB1300SF, LLSize is just right, Spec. is a little different, but I bought Repeat of the same product. The front and rear tires are also hidden to the bottom. The holes for the front and rear tire locks are thick enough to fit. The back is now black so it is easier to put on. The fabric is thick and durable. The one I used before could be used for 4 or 5 years, but I can't put it on while the exhaust system is hot, so I put on the small one after an hour. I have used other manufacturer's products, but I want to keep my Motorcycle in Large size, so I think I will repeat this next time. View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
There is an effect that can be seen in the "Hadrill
Vibrations at highway speeds are noticeably reduced, at 80km I don't feel it at all, at 90km it's just a little bit bothersome. Motorcycle is the New Model Eliminator. View detail
I have no particular problem using it.
It is a consumable item that is used for a short period of time, so it is very helpful to be able to purchase it at a reasonable price. I have no problem using it. View detail
Fits: KAWASAKI ZZR1400, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI ZZR1200, KAWASAKI ZRX1200DAEG
Good for Normal tank cap
I bought it to use for a tank cap for my Accosat, but after receiving it, I realized that the Bolt shape was different and never used it.
It can be used to change the bolt on a normal tank cap, so I think it is an easy way to dress-up the cap!
Purchased for ZrX1200R.
Bolt size is the same, so I think it can be pontooned.
View detail
SUNSTAR Racing Steel Sprocket
Item safe landed..packing was perfect..correct item.my second set for my next change.very good product from sunstar.very surprise package arrived super fast within 3days..well done TEAM WEBIKE!!!.. awesome..highly recommend to shop at webike.thank you.more comming View detail
Black so it looks tighter.
What made you decide to buy?
Since the beginning of the New Year 2024, I have been gradually collecting parts and trying to carry out a customization that I have been envisioning since last year … that customization is to replace the front rear sprocket and chain. Why did I choose the Sunstar Racing Steel rear sprocket? The reason for choosing the Sunstar racing steel rear sprocket and chain is that the power and traction control of modern supersports are constantly subjecting the sprocket and chain to high and fluctuating loads. Although there is no change in weight with the stock steel and Sunstar also made of steel, we chose a rear sprocket that delivers super durability that can take the power.
[How was the installation?
When replacing the sprocket, you will need a racing stand to lift the rear tire and a long spinner handle to loosen the axle nut. Also, a Torque wrench is necessary for Torque management.
Float the tire on the rear stand, loosen the axle nut, pull out the shaft, and remove the wheel. I always use a scrap tire from a car to put the removed wheel on the stand. I always use a scrap tire from a car to put the wheel on the stand.
While removing the Rear Sprocket, it is a good idea to clean up the area around the back of the Sprocket that has become sticky with the Chain lube. After cleaning, fix the Rear Sprocket, but since there is a little play, fix the Sprocket nut while pulling the Chain in the direction where the Chain is pulled. It is recommended to mark the Sprocket nut to confirm the tightness.
How was your experience with it?
At first, I was not sure if I should reduce the number of pins and make it Long, but I didn't want to have a misprint on the Speed display, and I also liked the ride quality of the OEM, so I decided to use the same 43 pins. So there is no change between before and after the replacement, but the OEM 6R is easier to handle. 21 year old ZX-6R has Front 15T, Rear 43 Dings, Reduction Ratio 2.866, Chain linkage 112.
View detail
To match the Gold amount up to free shipping.
As per Title, I bought it to get free shipping.
We strictly follow the routine of one in every two Oil changes, so this is fine.
This one also has an O-ring attached, which is convenient.
There were two types of large O-rings in the package. I used the one with the smaller diameter wire, but I think it is fine.
Is it because of these two types of O-rings that I feel like there are so many compatible car models listed?
A certain "Kansai Soul", which is only cheap, is poorly made, but I think this one can be used with peace of mind.
View detail
![TAKUMI Motorcycle Cover Ver.2 [LL]](https://img.webike-cdn.net/catalogue/images/21036/photo1_TS.jpg)
Fits: BUELL S3, KAWASAKI GPZ1100F, KAWASAKI GPZ750F, KAWASAKI Z800, KAWASAKI Z750, KAWASAKI Z1000, KAWASAKI W800, KAWASAKI W650, KAWASAKI W400, KAWASAKI H2SXSE+, KAWASAKI GPZ750, KAWASAKI GPZ1100, HONDA VTR1000F, HONDA VFR800, HONDA VFR1200, HONDA RVF750K, HONDA RVF750, HONDA NC700S, HONDA CBR1100XX, HONDA CBR1000F
I purchased the Motorcycle Cover because it was out of date.
The handling is very easy and the double structure is very good for a Full Cowl Motorcycle Cover.
Also, GSX1300R HAYABUSA (Type 2) I was able to install the Cover with the GIVI Top Case Bracket still in place.
View detail
I got a lot of iron powder.
I used it to clean up my new MONKEY125. It was my first and second DIY oil change, but it was done without any problem. View detail
Thank you Plus mu.
I had never used a disc before, so I had no knowledge of how to install it, and when I looked at Mu's installation instructions carefully, I saw a note that said to use two shims for a 4mm disc. However, the box contained only the number of shims I requested. When I called them to ask for an explanation, they responded in detail and kindly. Thank you very much. Thank you very much. I don't know if it is because I bought a slightly old motorcycle used instead of a recent motorcycle, but the floater was removed due to deterioration, and I had to replace it with a new one. But I didn't have the courage to replace a disc with almost no miles on it, and I found Plus mu through the ad-vise of PhoLower. I think that there are people who buy old motorcycles in pursuit of romance, not only my motorcycle. But please don't worry. If you have Mr. Mu's products, even if you are in my situation, you can revive your OEM. I am sure you will be satisfied economically, visually, and in terms of customer service. I apologize for the length of this message. View detail
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
Shorter than OEM
[How is it used?
Since I changed to Marchesini Wheels, I decided to buy Titanium wheels anyway.
Was the installation difficult?
Just apply Screw locker and tighten.
How was your experience with it?
Though it cannot be noticed or experienced by others.
The sparkling Titaniumium Bolt is one of self-indulgence
Also, they don't rust like iron Bolts.
Could be good for someone who wants to clean it up.
[Included Parts:were they on?
No. Prepare and apply your own Screw lock agent before tightening.
[Was there anything that disappointed you?
I don't know.
[Points to note]
OEM is 30mm while Zita is 22mm
Change to the optimum length for an OEMBolt that is too long
They say it contributes to weight reduction.
If you're worried about it, there's a 28mm version, so you might want to choose that one.
Marchesini is 22mm in appropriate size, so you can keep 22mm.
The Bolt in the middle of the image is the Bolt that comes with Marchesini and is too long.
Be careful not to scratch the Wheel through the Adapter.
How did it compare to other products?
The good thing is that it is much cheaper than βTitanium
βMaterial:While Titaniumium costs less than 3000 yen for 1 pc, Zita's is less than half the price at 1243 yen.
If this is the only one, βMaterial:You can choose Titaniumium if you want.
The difference between the front and rear wheels is 24,000 yen.
If you want to use with color, you have to choose βTitanium, but I chose Zita because it has a good base.
View detail