For CB250F

really genuine product. Finally I bought it from webike. It is genuine. Very good packaging. Thanks to the webike team. View detail

After 10,000 km

Purchased due to Idling failure. It has been improved. View detail

For THRUXTONRS

OEM replacement for Triumph is not available, but if the OD and internal Screws match.
Can be installed. Always change Oil and Drain plug Magnet
This product gives me peace of mind when I look at it and worry about all the iron dust.
Overall length is slightly longer than tiger OEM, but no problem for installation. View detail

regular product

Just by holding the product before opening the package, you can see the hadrill and lightness of the product. Since this is the SUNSTAR, precision and rigidity will not be a problem. The color is elegant and you can dress up your feet casually. View detail

A little short, a little thick

I installed it on a ZrX1200ZrX1200 DAEG and it was a little short in overall length.
I think 125mm is just right. i bought some Sponge from Home center and filled the gap.
The thickness is about 33mm compared to about 30mm for OEM. It is just right for me. It may be too thick for some people. View detail

Titaniumium color!

Small but finely crafted
Luxury that you can feel in your hands
Worth the Gold! View detail

Small

I bought it for my BMW R1150GS because it fits VST 1050, but it is smaller than I expected. I bought it knowing that it would not fit over the SIDEPannier, but I did not expect that it would not fit over the Top case either. The storage is compact. View detail

I chose it for Large type Adventure.

I bought this for my BMW R1300GS. I chose the 4L model based on the model that fits the car and it was the right choice.
However, since I do not have a Top case or Large case on my GS, the Rear area may be small when it is attached.
I have purchased several Motorcycle Covers in this series and they come with a Heat Seat to minimize the effects of Exhaust System heat. When this is attached, even if there is a little heat in the Exhaust System, it does not affect the Cover. View detail

Iridium plugs

Iridium plugs have also exploded in ignition! View detail

To change the oil.

Purchased to replace Element along with Oil replacement.
It was well made and worked fine. View detail

There was no one with Level gauge.

The OEM Product was not strong enough, so it was replaced. After installation, I found that the flange surface is narrower than the OEM Product, so there is a gap between the OEM Product and the engine side. I would have liked to have had a product that fits Exactly. View detail

The size is just right and the texture is good.

Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner. View detail

vfr800 rc46Brake Pads

I've got a vfr800 rc46 front wheel Pad that's getting low.
I bought this for my own effect.
Golden Pad is still the best choice for braking performance and durability.
I went with this one. It is a safe performance to ride. View detail

Great Control

There were few options for Pad for Pin slide caliper for my Motorcycle, only Resin pad.
Since brembo has lineuped Sintered pad, I bought it without hesitation.
After the replacement, the new wheel is acclimated quickly, and both control and braking power are dramatically improved.
I was surprised to see how much difference just a pad can make.
I don't know about the durability yet, but I am satisfied with Large when I experience such high performance. View detail

NGKWindshield IRIDIUMSpark plug

I think the texture is good and the cosmetics are good. View detail

Uotani and Quantity:Exchange in Set

It was replaced along with the cord and Cap when the Uotani was installed.
Iridium plugs do not require Gap adjustment, but were adjusted to 1.2mm for the Uotani installation.
It might be interesting to compare it with the Normal plug, although I haven't done it yet. View detail

cheap

[How is it used?
Oil replacement once a year
How was your experience with it?
I don't have a measuring machine and I don't know what it feels like.
How did it compare to other products?
The appearance is like OEM is expensive.
Functionally, is the amount of Filter inside more than OEM? And?
Gold is inexpensive and the Brand is a classic, so I personally feel secure.
[Points to note]
I think it's about conformity caution. View detail

Hey!

Contact Person!
I thought I sent you an email telling you to Cancel! View detail

DAYTONAOil Filter

I wanted to replace the oil and filter by myself, and after a lot of research, I found DAYTONA's products! I recommend it! View detail

Made by Windshield IRIDIUM, which I have been using for about 20 years now.

Iridium plugs have been a favorite of ours since their appearance.
I am not dissatisfied with the performance of the Standard Plug BP5HA, but I use it as a talisman because it makes a difference when I have a Large fuel consumption problem in a Carburetor car (extremely cold mornings, or when going downhill on a long slope with almost no throttle).

I have never felt the Power up or Torque up as described by Manufacturer.
But with the Standard Plug BP5HA, it keeps igniting well (I think) even in a situation where it could have possibly lost fire, so I have been buying it for lightly 20 years now.

In particular, LargeEngine Displacement Volume TWIN and Single engines are prone to fuel mixture collapse except at full throttle (a different story from the carburetor setting), so the peace of mind that ignition is solid even in situations where the air-fuel ratio is clearly not correct is irreplaceable.
Windshield IRIDIUM was originally made by Denso, but I had a bad experience with them in the past, so I use NGK products.
I guess Denso products are already Large sturdy now, though.

Replacement time is Whenever I feel like it." It is
When I remove it and look at the electrodes, nothing has changed, so I could use it forever if I wanted to. It seems as if it could be used forever if it wanted to.

Plug replacement is one thing, but a clean plug hole is even more important, so we put a tap through the plug hole to remove carbon without having to replace the plug.
If the plug hole cannot be easily screwed in by hand to the end, it is a sign that Carbon has accumulated in the plug hole.
If Windshield IRIDIUM is the way to go, at least Plug should be able to turn round and round by hand to the end! View detail