Reviews
Yearly update?
I replaced the Front Disc on my 89 MD24.CRM250RK with a new one due to a Brake Overhaul. The original Rotor is still usable, but I replaced it hoping for a slight improvement in touch. The replacement was easy, but the OEM front hub cover could not be installed, so I applied anti-loose agent according to the service manual and tightened at 1kg/cm (98N/m). In the test run, I did not feel any difference in the touch and the braking power, partly because I had not yet gotten accustomed to the pad.
However, the lack of wear would be expected to improve Touch.
View detail
For CB250F
Earlier I encountered some noise in my bendset. After inserting this the sound went away. genuine product Cost performance and comparison with other products Good value for money. About shipping and packaging Fast shipping and very good packaging. highly ercomended. View detail
Thank goodness it's readily available.
I used KIJIMA oil for replacing the oil in my KLX230R. I bought KIJIMA oil because it takes a long time to deliver OEM products and they are often more expensive than the Replacements. I was able to replace the oil without any problems. View detail
CB250F MUFLER GASKETS
Genuine product -GASKET,EX. PIPE 18291-MN5-650 About quality and texture genuine product Cost performance and comparison with other products Good value for money. About shipping and packaging Fast shipping and very good packaging. highly ercomended. View detail
Buy wisely in bulk! Recommendation for those who own several motorcycles!
10 pieces Quantity for business use" at a great price:The "Set" is a great recommendation for those who own several motorcycles, because you can buy them in bulk at a low price! It may seem like a lot to have 10 sets at once, but I have a Ninja 250SL and a Z125, and the discount is very helpful for me! View detail
I appreciate the affordable price.
[How is it used?
The KDX220 I purchased used was not in bad condition for an old vehicle from the 1990s, but the seat cover was in a slippery condition because the surface had begun to harden, probably because it was from that era.
On the way home after taking delivery of the car at Motorcycle shop, my buttocks moved back and forth every time I accelerated or decelerated, making it very difficult to enjoy the ride, and as soon as I started driving. The first custom was to reupholster the Seat Cover. It was like that.
Originally, I was going to bLOOVE it, including a look at the vehicle, but I went home right away and looked at Webike's product introduction section. KDX220 Seat I've been searching for...
Since it is an old vehicle, there are not many choices, but I-Net's Off-road Vehicle UniversalSeat Cover was a hit, and the price is low! If by some chance I fail, I'm ready to give up." So I bought it
How did you like it?
As a universal product, it is not as good as the Seat fabric made by a three-dimensional manufacturing process for each car model, but I personally think that the KDX Seat itself is not a complicated shape, so I was able to stretch it well.
The new fabric is highly flexible and the dimpled finish gives it a high grip, so you can enjoy riding without being carried back and forth every time you accelerate or decelerate.
To be honest, I wanted to stick with the OEMSeat Cover, but after looking at the price, the thickness of the fabric, and the condition of the finished product, I felt this product was sufficient.
How did it compare to other products?
There are few choices in terms of car models to begin with, and other products are expensive and have stopper belts sewn into the seat surface. I mean it!" I couldn't choose one because I had a strong feeling that it would be embarrassing to me, as I have poor driving skills.
What points should I pay attention to?
Patience and ingenuity are required because the products are not three-dimensionally sewn for car models.
If the tucker is driven in too shallow, there is a risk that the fabric will break from the tucker.
Front and back of the Seat are loosely secured to the Quantity:Pair (for Left and Right) When pasting the "Beauty" sponge, it should be pasted along the "Seat sponge" without wrinkles to make it beautiful.
Other items that would be helpful
The deciding factor in the purchase
The only Seat fabric that was safe for normal use was sold only by iNet.
We were not able to confirm that the products were made by KawasakiOEM, so we did not consider them in this case.
[How is it used?
Basically, it's Main for city driving. I can't even use SEROW, so it was too Hurdle for me to play in the mountains with a 2CycleEngine equipped car.
【Included Parts:presence or absence】.
Seat CoverQuantity:1pc. with Instruction Manual and Vinyl for waterproof.:Set
Tandem belt is not included, so those who need it must purchase it separately or reuse the OEMBelt.
[ITEMS TO BUY TOGETHER
Seat fabric to fasten to Seat Base seat. Tucker. and short-legged core.
It may not be necessary for those who apply Vinyl underneath, but for those who apply directly to Sponge without Vinyl, it is better to prepare SiliconCoking agent to be applied to the reverse side seam of the Seat fabric.
Opinions and requests to Manufacturer.
Although it may not be a problem for popular cars, it is a product that older cars and minors cannot do without, so we hope you will continue to sell Lineup for a long time.
View detail
Grip is amazingly durable!
[How is it used?
This product was stuck on an XR250 Seat that was purchased used by a person at work about 15 years ago from the beginning.
The vehicle had been restored to the best of my ability at that time because the exterior of the vehicle was damaged except for the Seat, and after many years it came to me a few years ago.
The exterior of the car was damaged by ultraviolet rays, and the tires were badly cracked and the brakes were sticking to the car.
Sorry for the long preamble, but even in such a state of exterior rustling, only Seat remained flexible.
The surface had lost its Luster due to water stains and dust, but after washing the car and applying a protective material, it returned to the condition it was in 15 years ago.
It is indeed a product sold by Webike for 10,560 yen, and is definitely more durable than the OEM Seat Cover.
How was your experience with it?
When the car came into my possession, I again did Restore maintenance on each part of the car, but I drove it for a while without reupholstering the Seat (I eventually replaced the Seat Cover with another Manufacture's one to match the repainted exterior).
GripperMaterial that "Demonstrate Exceptional Flexibility and Grip Power" as the manufacturer's slogan says, is used throughout.
Assist Rider's Machine Control. The flexibility and gripping power did not deteriorate even when exposed to ultraviolet rays, rain, wind and dust.
How did it compare to other products?
As I mentioned above, I had replaced it with a Dimple-finished Seat Cover made by another company, but the Seat Cover remained as flexible as a new Seat surface after more than 15 years. I think it is phenomenally Tough.
[Points to note]
Not so much as a warning, but the moat on the Seat Cover named GripperMaterial was deep, and if the Seat was bathed in mud, the dirt would get into the deep moat and be difficult to remove.
The product is three-dimensionally sewn for XR250 (MD30), so it is relatively easy to work with if you have experience in Seat reupholstery in the past.
Other items that would be helpful
The deciding factor in the purchase
As I mentioned at the beginning, it was already stretched at the time of purchase on a used car.
[How is it used?
Basically, it is a city Main, and I am fully aware that it is a high-performance Motorcycle for a 4StDual PurPass car at that time, but I could not handle it because my feet could not reach the ground on rough terrain, and I lacked the skills.
【Included Parts:presence or absence】.
Quantity of 1 Seat Cover and Instruction Manual on how to apply.:Set
I don't think there was a tandem belt attached.
[ITEMS TO BUY TOGETHER
Seat fabric to fasten to Seat Base seat. Tucker, a slightly larger version of Stapler. and short-legged core.
The fabric joints are crimp type like OEM, so there is no slippage, I think Coking agent is not necessary.
Opinions and requests to Manufacturer.
An indispensable manufacturer in the off-road motorcycle world.
We look forward to your continued development of a wide variety of lineups.
View detail
Good quality part!
Fits my USA XR400R perfectly! Good quality OEM part. These help keep the swingarm grease clean. Once the rubber is dried out or cut up, it's time to replace them. This is especially important on a dirt bike, where mud and water are likely to get in there. The rubber on the parts I received was very fresh feeling. View detail
FOR CB250F
reasonable price.Carburetor o rings. It is Genuine. Very good packaging. Fast shipping. Thanks to the webike team. It has not been installed yet. Highly recommended. View detail
Genuine Honda Rear Piston Seal Set for CB1000R 2011
These was a set of replacements for a broken piston seals for the CB1000R I have in the garage. I found that a few of the seals were not in great condition but these ones actually split and deteriorated. I purchased a set so I now have spares if any are still ok already on the bike. I found the correct part using the help pages and links that Webike provide. All with some other parts were shipped and delivered to my door in 5 days. These are small seals and do need a little care when being shipped. No problem at all for Webike, they put them in a nice bubblewrap envelope and were already on the Genuine Honda packet anyway. They were kept flat so there was no damage to the seals. As I already had the caliper apart for servicing, this set of seals were super easy to install. They arrived in perfect condition and had enough flex to be able to seat correctly. All back together and now that is one of the jobs completed. Thanks Webike, great work. View detail
DJEBEL250xc.
Installed on a DJEBEL250xc, cutting off the OEM ignition coil in the middle and connecting it. It is a recommendation to refresh the electrical system. View detail
CB250F
I am happy to work with the webike team.Actually this item i could not found in my country (Kyatsup 14MM 90084-MN8-010). Finally I bought it from webike. It is genuine. Very good packaging.fast shipping. Thanks to the webike team. It has not been installed yet.good for the genuine buyers.highly recomended. View detail
RubberSIDE
The installed product was badly deteriorated, so it was replaced with a new one.
It is good that the same HondaOEM Product is available, but it is somewhat expensive for a Rubber part.
View detail
Good Brake Pads
Very good Control. Durable and reliable. View detail
Improved serviceability
OEMs can replace the 2-parts configuration of the Hexagon Bolt Pin+Minus screw blind with a single 8mm bolt.
The 8mm bolt is also used frequently for maintenance around the brake area, so the assortment of tools can reduce the man-hours required for the work.
In addition, the OEMs were concerned that the outer screw would burn even if Thread compound was used, and the use of a slotted screwdriver would cause the screw to lick every time it was removed, but due to the characteristics of the screw, the possibility of this happening is relatively low. 。
(We still recommend the use of CopperGrease on threads, as seizure itself will occur.)
Replacing one Brake pin will not make you run faster or ride easier, but it will reduce the burden of maintenance.
View detail
Fits: HONDA XL250 Degree MD31, HONDA XL250 Degree MD26, HONDA XLR250 R (Baja) MD16, HONDA XLR250 R (Baja) MD20, HONDA XLR250 R (Baja) MD22, HONDA XLR250 R3 (Baja) MD20, HONDA XLR250 R3 (Baja) MD16, HONDA XLR250 R3 (Baja) MD22, HONDA XR250 (Baja) MD30, HONDA XR250 (Motard) MD30, HONDA XR650 L, HONDA XR650 R RD06, HONDA XR650 RE01, HONDA CBX250 RS MC10, HONDA CBX250 S MC10, HONDA CBX250 SS MC10, HONDA XR400R NE03 96-98, HONDA XR400 Motard ND08 05-09, HONDA XR600R PE04 85-93, HONDA NX650DOMINATOR RD02 92-94
It is the best cospa
It can be used in the same way as OEM Product and is very cost effective.
The product was highly accurate and there were no oil leaks, etc.
View detail
reasonable price
I recommend this as a very basic model.
I recommend it for both price and durability. Of course, it also helps in terms of appearance.
It is more helpful in terms of neatness than the rubber plate of the original footrest. I think that such small details are of great help when tuning.
The shoes fit perfectly into the body! Avoid bare feet
-------------------------------------------------- -------- Recommended as a very basic model. Recommended in terms of price or durability. Of course, it helps in appearance. It is more helpful than the rubber plate of the genre of the footsteps. Shoes are just wrapped in the body! Please refrain from bare feet Powered by Google Translator
View detail
Two layers are recommended.
Cover is 2L Size, body is XSR900 (RN56J) The parking lot is used for open-air parking.
When I bought a new car, the dealer gave it to me as a purchase bonus and I was using it, but I had been using it without tightening the String at the hem, and there was a hole where the footpeg hits, probably from the wind, about the second year of use.
I bought the same product because I was not sure about the Size feel of the other company's product, as the dirt that clearly shows the Cap part of the Tank on the Others was floating around and I thought the open hole would widen if I continued to use the product.
However, the first Cover was still usable, so we decided to use two pieces with the new one inside.
As a result, two layers are good. The old outer cover is getting a large amount whiter in the front blue area due to sun damage, but the inside is still as blue as new and the fabric is still soft.
As a Motorcycle Cover, it is convenient that there is a part to put a Wire lock and a Chain lock through the front and rear Wheels. There is not just a hole, but a notch, so it is easy to put the locks through.
Size feeling is that if you don't squeeze the String at the hem, you can't get the size you want, especially Quantity.:Pair (for Left and Right) It may be good for those who want to cover it completely as the hem is just hanging on the ground with excess hem on the sides.
Instead, I don't think moisture will escape, so if you are concerned about moisture, I think the F Type with Ventilation would be better.
View detail
Fits: HONDA CR125R, HONDA CR250R, HONDA CRF150F, HONDA CRF230F, HONDA CRF250F, HONDA CRF250R, HONDA CRF250RX, HONDA CRF250X, HONDA CRF450L, HONDA CRF450R, HONDA CRF450RX, HONDA CRF450X, HONDA CRM250AR, HONDA SL230, HONDA XR230, HONDA XR250, HONDA XR250BAJA, HONDA XR250MOTARD, HONDA XR250R, HONDA XR400R
Inexpensive and good quality
Wanted a good quality black sprocket, but didn’t want to spend $100 This is the first dura sprocket I've used and for the price the quality seems impeccable!This sprocket looks to be well made, fit good, finish good, wear good,. The fit is spot on and Id say even if it doesn't last as long as other more expensive brands (nothing leads me to believe it wont) its worth the cost. It looks great on the bike and seems very well made. Time will tell.i like the look, but still DRC is making good stuff at affordable prices and don't get me started on the prices these days.fast shipping,great packing.thank you Webike. View detail
Fits: KAWASAKI KLX250, KAWASAKI D Tracker, KAWASAKI KDX220, KAWASAKI 250TR, KAWASAKI KSR110, SUZUKI RMX250, SUZUKI 250SB, SUZUKI HUSTLER, SUZUKI DJEBEL, YAMAHA TW200, YAMAHA XT250X, YAMAHA TT250R, YAMAHA SEROW, YAMAHA XTZ125, YAMAHA WR250, YAMAHA DT50, YAMAHA PW50, HONDA FTR250, HONDA CRM250R, HONDA CRF450
Anyway, it's the lowest price in Fat bar!
I thought I bought the High type, and it says so in the Package...
I have compared it with Landy's Low type, but the height is the same...
Huh? Isn't it low? Something doesn't seem right. 。 It's probably not your imagination.
The handlebar is quite high on the VST250SX, so I managed to install it with three clamp extensions.
This seems to be a bit of a turnaround...
In addition, since there is a hole in the blinker and the Axel collar, I cut it out and wrap a piece of tape used for tennis racket or bicycle grips around it to prevent it from slipping.
It's working surprisingly well.
View detail