Reviews
Genuine Yamaha Gasket for XT250
Whilst I was changing out the oil and already purchased the new oil drain plug, I wanted to make sure I had a good seal so also purchased the genuine Yamaha gasket for this bike. This is only the second oil change I have done on this bike but it is only a 2019 model anyway. The correct gasket was found when I checked for the correct oil plug. Not too tricky when you have the Yamaha schematiics in front of you. The price was really good value, yes, you could get a pack of cheaper after market gaskets but for this money, why would you risk a good seal. Anyway, with a couple of other parts I needed including the oil plug, I had my order shipped using EMS. My order arrived in perfect order and 100% no damage in 5 days straight. The gasket was in the usual Yamaha clear packet. There were no contaminants inside the packet which was nice. The washer looks to be copper but I would assume it is a copper and some other metal mix. Easy job to do replacing the gasket and oil plug but make sure not to over tighten. Use a torque wrench and make sure you have it right. Very happy customer. Great work Webike. View detail
Genuine Yamaha Plug Straight Screw for XT250
One of the only parts I do insist on changing is the oil plug on bikes after and oil change. Mostly due to the screw becoming a little messed up and could be harder to remove over time. Even though this bike is a pretty young bike, it has a lot of years left in it and I would hate to have to drill out the bolt to change oil in the future. The correct part was found by using the tools Webike provide on their help section. I then did a cross reference with Yamaha schematics to make sure. The screw was not expensive but when you get a genuine Yamaha one, you know it will be perfect for the job. With a few other parts, my order was shipped using EMS and arrived in one piece and perfect condition in 5 days. The screw came in the standard Yamaha packet and wrapped in bubble wrap envelope. It was really clean on the threads and no shards or swarf were found. Along with the genuine Yamaha gasket all was fitted eas=ily and no leaks once torqued correctly. Very pleased witht his purchase. Cracking work Webike. View detail
Large satisfied
I have been asked by my daughter for a long time, but due to the severe cold weather this year, I bought it. (Scooter) So I had a hard time removing the cowl, but I am Large satisfied with the contents of the product. I have several other motorcycles, so I plan to purchase & install them one after another. I think it is very cost effective! View detail
Good product that can take 3 power supply outlets
I bought it to get power for Tachometer and ETC. The unneeded harnesses are mercilessly cut off and used as materials for other electrical work. The harnesses are too long and are in the way, and they become harness resistors and waste energy. The output side harness is also long, but do not cut that one off. The harness is connected to the battery and ACC power source, and is energized when the key is turned on, so there is no need to worry about the battery going up. The included instruction manual is very carefully written, so please read it carefully before you start work. View detail
best grip heater
This is 3rd time i use Kijima grip heater. I think this is the best grip heater, it is thin as original grips and included aluminum tape helps hold the grip quite strongly on the handlebar without addhesive, of course need to make effort little bit to install. View detail
ALCAN hands iGrip
I have used it for VTR250 and MT-03, and I bought it again this time. The color is Orange red to match the body color, and it is a good accent for the handlebar. When I installed it, I used a small amount of glue to prevent shifting and decided not to use wiring. View detail
DJEBEL250xc.
Installed on a DJEBEL250xc, cutting off the OEM ignition coil in the middle and connecting it. It is a recommendation to refresh the electrical system. View detail
KIJIMAGrip heaterGH08Push Switch
It's been about two weeks since I installed it and so far no problems.
The Grip is a little thicker than I expected, but it is just right for me. I was thinking that I would mishandle the Switch if I used the type attached to the Grip, so I chose this type, and it was the right choice. It is easy to operate and I feel it is convenient to attach it anywhere I want. Also, my palms are quite warm if it is 4 degrees Celsius in the morning and the temperature is at the maximum. But only my fingertips are hard to keep warm. If you want to keep it on all the time, I think the 3rd or 4th of 5 levels would be best. I think the 3rd or 4th out of 5 levels would be best if you want to wear it all the time.
Electrothermal Gloves or Inner Electrothermal Gloves (You will need to bring your own Gloves separately) Would it be good to have a And.
With the skin Gloves with boa, the palms will feel sweaty.
View detail
I wanted Cap.
I purchased this product to connect to the Ignition coil in Mukawa and wanted to unify the colors.
Cutter off the adhesive bonding the Cap to the cord, peel off the Cable outer skin of the Mukawa Ignition coil, insert it, and fix it with adhesive, and you are done.
The excess Cable of the product in question is used in place of the Cable attached to the OEMCoil.
This would have been unnecessary if caps in a variety of colors were available, but they are not.
Even if only the cable is replaced, the idling is stabilized and the long-used OEM product is refreshed.
View detail
Power cable & elect. module Dev'moto
Bonjour from France Thanks you for quick shipment of my order , i fixed it on ma yam sr 125 in addition of a new electronic module Dev'moto(made in France) with an iriduin plug already than replace the TCI -dead-:( the result is more better ( already too with the new module) cold cranking + little better torque at low rpm, and more i could reduce my idle setting ... so very happy with my purchase ... voilà ! View detail
reasonable price
I recommend this as a very basic model.
I recommend it for both price and durability. Of course, it also helps in terms of appearance.
It is more helpful in terms of neatness than the rubber plate of the original footrest. I think that such small details are of great help when tuning.
The shoes fit perfectly into the body! Avoid bare feet
-------------------------------------------------- -------- Recommended as a very basic model. Recommended in terms of price or durability. Of course, it helps in appearance. It is more helpful than the rubber plate of the genre of the footsteps. Shoes are just wrapped in the body! Please refrain from bare feet Powered by Google Translator
View detail
Required in winter!
It has been 3 months since I installed the Grip heater on my NC750X and the day to use the Grip heater has arrived. The warmth is not a problem, but the Horn is above the blinker on Honda cars, so the blinker is not easy to operate with winter gloves. Since we did not expect to use Winter Gloves when we installed the Grip, we had to change the position of the Grip in a hurry. Even after changing the position, the connectors on the Grip heater are still in the way (especially when turning right) and the operation is not easy. You may get used to it, but please be careful if you drive a Honda car. View detail
no problem
I have Repeat several times. I don't know about the performance because I can't experience it, but I have no problems with it. View detail
Vmax1200.
I got this because it was cheaper than OEM. Nothing wrong with it. View detail
good choice
I bought it after seeing a review that you often replace it with a set with Takegawa reinforced coil. I bought any color because it was hidden in a cowl, and I connected the ngk power cable with the Takegawa reinforced coil and installed it. I had to cut the length and install it, but I thought there would be some loss, so I just connected it. It starts up well and I think it's effective in output. Thank you. View detail
Fits: YAMAHA XT250, YAMAHA 250SEROW
Only regret is the high price.
The product is good, and if the price was lower, there would be nothing to say about it.
I think half price is a reasonable price.
View detail
Genuine Yamaha Valve Stem Seal for XT250 2014
Some of the valves on this bike were ready to be redone and sometimes the valve stem seals can perish and this was the case after inspection. I decided to just go ahead and buy one anyway as it is not smart to change valves and not sort out any other issues along the way. I found the part relatively easily enough using the Yamaha schematics for the bike model, these are pretty much the same throughout the XT250 range anyway so not hard to find. The cost was really good value so why would you not just change it out anyway. I did only need the one which was handy as the other looked pretty good. A few other parts with this were ordered together by EMS and delivered in 5 days. All my order was delivered with no issues, all the gaskets were kept flat so not to damage. This gasket is not a big one but it does have some intricate details that need to be correct to fit the cylinder. You can see it has been manufacturered the right way and not cheaped out on it. It is sturdy and has a slight flexibility. The fitting went in pretty easily too. Fitted quickly but precisely in just under an hour with everything else put back together. Very pleased with this one, the bike does sound and run a lot better and I know it will last a fair few years to come. Thanks Webike. View detail
Fits: YAMAHA TW225, YAMAHA TW200, YAMAHA DT230LANZA, YAMAHA DT200R, YAMAHA DT125R, YAMAHA DT200, YAMAHA BRONCO, YAMAHA TRICKER, YAMAHA XT250X, YAMAHA XT250, YAMAHA XT125, YAMAHA TT250RAID, YAMAHA TT250R, YAMAHA SEROW250, YAMAHA SEROW225, YAMAHA WR250X, YAMAHA WR250R
Matching Clutch Side's Pivot Perch CP
[How is it used?
I bought a used WR250R and the clutch lever was replaced with a ZETA Pivot perch (Brake Side was NORMALLever), so I bought a Brake lever to match the same design.
Was the one you received as per Image?
The design and Touch is Pushing and Parenthesis is good, and although it takes a little effort, the grip can be adjusted. To some extent." The finger lengths can be accommodated in the following ways
Was the installation difficult?
The installation process itself is easy, as it is simply a reverse of the procedure for removing the OEM lever.
Grease up each movable part firmly at the time of installation to ensure smooth and reliable operation.
How was your experience with it?
In my case, I had no complaints with the OEM Lever, but it is nice to have an adjustable grip.
The design is good and the texture is high. "Good goods" The sense that you are attaching a "+" is high (the price is actually high enough to be worth it...).
[Included Parts:were they on?
An illustrated Instruction Manual is included with the Pivot leverBody.
[Was there anything that disappointed you?
None
Basically, it is simple parts with a high quality feel, and it seems to be durable.
Other items that would be helpful
Point and hang of installation
As mentioned above, grease up the moving parts.
Then, you can install them neatly and faithfully to the basics.
[Availability and clarity of the Instruction Manual
A simplified Instruction Manual is included.
However, if you are able to remove the OEM lever, you should be able to start work with confidence, as the product is so easy to understand that you will not have any trouble installing it.
[Notes]
Tighten Torque properly.
[ITEMS TO BUY TOGETHER
In my case, as I mentioned above, the Clutch Side was replaced by the previous Owner, but if both were OEMLever, wouldn't it look better to have Both Sides in the same product at this time?
If you have a budget to spare, you can buy a hand guard of your favorite brand.
[Opinions and requests to Manufacturer
The price is a bit high for a LeverSingle Body, but I think it is worth the price, so please continue to sell the product as long as possible.
View detail
Genuine Yamaha Gaskets for MT07 2020
I wanted to get a few of these for future projects and it just so happened that one of these was also needed for the rebuild job on the MT07 2020 that had an accident and needed sorting out. This gasket was for the water pump to keep it from leaking. Not really a hard part to find as this one like a lot of other gaskets from Yamaha do fit a host of other models. This is why it is good to get more than one when I order from Webike. The part was easy to find using the tools Webike provide in their help sections and then if you like to cross reference, do this via Yamaha schematics. Simple. With a lot of other nuts, bolts, washers and gaskets needed to complete this rebuild, I had a lot of the parts shipped together to save me on shipping cost. When you add a few other parts, it really does work out cheaper in the long run. Also, EMS saves me time by shipping in a efficient manner and gettting my order to me fast. In 5 days from shipping, my order arrived. All my parts were in great shape, no damage caused in transit at all. I am not surprised really as Webike warehouse do a cracking job at packing the orders well. I got 5 of these washers and each came in a Yamaha packet. The gaskets are I think, copper but may be a composite but defintiely have copper in them. These are perfect as copper is a soft metal and will crush down to hold a tight seal. Exactly what you want for a water pump. Very pleased with the purchase and the gaskets are super nicely machined. Great work Webike, thank you. View detail
affordable price for good quality product
these item is very useful for those who want to get perfect spark for the bike - the Cables are designed for the serious racing enthusiast and feature high temperature silicone outer jackets, solid copper wire strand core and high temperature resistor covers, leading to improved engine performance View detail