Reviews
More than I expected…
I bought it for winter touring because I had some points left over and there was a discount campaign going on.
I can do electrical work and have replaced grips before, so I installed it myself.
Installation was easier than I expected, but it is safer to ask a store to do it if you are worried about the force required to press-fit the grips.
The key heat is effective at Plus temperatures, but not so effective at Minus temperatures. Well, it is better than nothing.
I have a Honda 400X with Honda OEM hand guard, so it is not directly exposed to wind, but even so, the effect starts to diminish from about 3 degrees Celsius.
It is better than nothing, but when I experienced HondaOEM's Grip heater on the 400X I rented from LenBarrel at HondaDREAM before, it was so hot that I could not grip it even at high speed in the morning in the middle of winter, and 2 out of 3 levels was enough.
This product does not get that hot even at max. 5 levels.
It seems that the temperature differs depending on the Manufacturer, and KIJIMA-made products seem to be lower than those of other Manufacturers.
Power is supplied from Honda OEM power supply coupler ACC.
However, the grip is very good, so I will give it an overall rating of 3.
Good points:comfortable grip and easy to install.
Five levels allow for detailed settings depending on the situation.
The bad:Not as hot as expected.
View detail
Good cosmetics, old standby.
[How is it used?
It has been a standard consumable for a long time. I use this Filter every time.
How was your experience with it?
The quality is stable and reliable. I am satisfied with the quality of the product and have had no problems with it.
[Points to note]
Even if you use Filter wrench, you may choose to use Wrench because it is a Type without corners. I have never had a problem because I stick the Driver in and remove it.
How did it compare to other products?
It is comparable to the OEM Product, and I don't think there are any problems. There is no visible difference in performance, but it is a good consumable item for periodic replacement due to its good cost performance.
View detail
Replaced at the same time as bremboDisc Rotor
Replaced together with bremboDisc Rotor.
It stops cleanly and has no control issues.
However, when you put it on, you can't tell it's brembo by its appearance.
View detail
On a 2011 CBR600RR.
I bought it because I didn't want to do thick Gloves in the winter.
The installation was done by Webike's Support store with direct shipping.
In the case of the CBR600RR, I gave up on it myself because it is Large strange to remove the FI side of the Accelerator Wire.
I have used it and it heats up so much that it is hot at the strongest Level.
My wish to use thin Gloves in winter was fulfilled as long as I warmed the back side of my hand from time to time.
There is no possibility of mishandling during Blinker operation.
View detail
I knew this was easy to use.
The fabric is thicker and has some stiffness compared to the Simple made by DAYTONA, which I bought last time, but I prefer this one because it feels more protective.
It is easier to have a belt sewn to the cover to prevent it from being rolled up.
The size is a little bit oversized around the rear, but I think the 3L size is good because it can wrap around the entire motorcycle.
View detail
It's worth the price
I think it is a good product. The only thing that bothers me is that the hole for the lock in the back is hard to find. My concern is that it will deteriorate over time. View detail
Cost performance!
It is a normal oil filter, no oil leakage and comparable to OEM. Cost performance is good. View detail
I expect it to be durable.
Replacement from Windshield IRIDIUM.
I don't feel much acceleration performance in city driving.
Idol I am looking forward to increased fuel efficiency and durability.
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker X, KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KLX250, KAWASAKI KSR110, KAWASAKI Ninja 250, KAWASAKI Ninja 250R, YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6 04-17, YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA MT-01, YAMAHA MT-07, YAMAHA MT-09, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA WR250R, YAMAHA WR250X
I wish it was 10mm diameter.
Purchased to replace LED Blinker.
Maybe it's compatible with Yamaha stuff or something.
Since I could not be sure, I bought a DRC product that I could be sure of.
This product is used between two pieces, so the front and rear blinkers are interchangeable.
2Quantity:Set is required.
Since the mounting hole of this product is 8mm diameter, the Screw diameter of the Blinker to be installed is also 8mm diameter.
The 8mm blinker is used, but there are surprisingly few 8mm-diameter blinkers.
The problem is that most of the products sold at low prices are 10mm diameter and there are very few options.
View detail
Reliable OEM
The XSR900 is the first DIY replacement.
There were cheaper filters available, but we went with OEM for reliability...
Well, I guess it's a matter of mood (chuckles).
View detail
Purchased with Rear disk rotor
I bought it together with brembo's rear disk rotor when I purchased it.
I haven't installed it yet, but I have no complaints about the quality and appearance of the product.
I will make an impression when I install it again.
View detail
I'm not sure what the difference is.
I have been using Iridium plugs.
I did not feel any difference in my experience when I switched to this Plug.
I will use it for about 10,000 km since it seems to be sold as "long life".
View detail
Fits: YAMAHA XSR900, YAMAHA XSR700, YAMAHA MT-09, YAMAHA MT-07, YAMAHA MT-10, YAMAHA MT-01, YAMAHA FZ8, YAMAHA FZ-1, YAMAHA FZ-1N, YAMAHA XJ6N, YAMAHA XJR400, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA TDM850, YAMAHA TDM900, YAMAHA WR250R, YAMAHA WR250X, YAMAHA SEROW250, YAMAHA DS250, YAMAHA SR400
Motorcycle Cover with good balance of price and quality
We recently added a Large size NAKED to our fleet, so we purchased the 2L Size.
I do not own any Yamaha Motorcycle, but all Motorcycle Covers are E Type by Y's Gear.
I am considering it for dust protection Main since it is stored under the eaves.
The new product seems to have been renamed E+ (ePlus), but I am not sure how it differs from the previous product.
I was relieved to see that the ease of use has not changed, with color-coding on the front and back to avoid hanging mistakes, and a draw cord to tuck in the hem to keep the wind from blowing in.
View detail
It is recommended
The Engine was in good shape, but the existing Plug had been used for more than 10,000 km, so we decided it was time to replace it with this product.
After the replacement, the vibration of the Engine seems to have decreased and the turning seems smoother, although the old one may have been worn out. I am glad I made the change.
View detail
And then I'll trade for it
I bought a used ZZr and it still had it! Oil leakage into the plug hole. I replaced the plug while I was repairing it. It seems to be a little better. View detail
Grip heater refill
I installed a replacement GH-10 that I had been using for 2 years, but it stopped working and during a Sale.
I was thinking of using something different, something made by DAYTONA or something with a separate controller, but I chose the GH-10 again because I thought the convenience of being able to operate it with a short push at hand could not be compensated for by the difference in price.
The Axel side is easy to install since it is integrated with the Throttle cone. The opposite side is difficult to install unless it is warmed up. Wiring is done by floating the Headlight in the back gap. It's still useful to have it from a little chilly season to winter.
View detail
Used for YamahaBOLT Shoulder Bag.
I have been replacing Oil with YamahaBOLT Shoulder Bag around 3000Km of running,
The oil filter is changed at the same time every two cycles.
In that case, Filter uses this YamahaOEM product.
If you choose by price, ThirdParty products are more attractive.
OEM is the only choice in terms of buying peace of mind.
I have used Other Brand Products in the past and had a very hard time removing them.
Since then, we always choose OEM Products.
View detail
Add on to Clamp on heated grips
Best bang for your buck, works ok, and i like it works/plugs in with clamp on heated grips! I have good luck with most all webike products. I purchased 1 of these along with the associated heated lock grips for my wife's and my bikes. Installation was straight forward after watching the videos. Just had a chance to try them out over winter break with temps around 10C - 15C. They took a few minutes to warm up, but did a great job. We typically started on a setting of 2 - 3, then turned them off after our riding activity increased. Very warm, even through our winter gloves. Great purchase, happy wife!Would recommend! Fast shipping as always too.Thank you Webike. View detail
Easy to install, better than ManufacturerOEM
The switch is integrated with the grips for easy installation, requiring only wiring and no effort.
It is also possible to point it straight up to avoid touching it when operating the blinker. If you warm up the Heater to the maximum Large setting, you can easily pull out the Grip.
The thickness is just right for general OEMSize and is a non-slip Material.
View detail
Excellent choice, cheaper than OEM.
Gotta have oil filters, right? I like to change filters often but don't want to put a bunch of money into it if I can avoid it.Great filters. I learned about these when I had an older bike and found out they supply alot of oem and aftermarket oil filters. Same quality as oem and there cheaper. Why not buy directly from the manufacturer. Never had an issue running these. The inner screen has extra large holes and the metal is folded nicely. The rubber grommets fit tight on the filter's metal end caps and they fit tight around the pressure relief insert Mt09. I give it 5 stars plus These filters are a good value and have worked great for us. View detail