Not very good

The paint on some of these has a bumpy texture, like the units weren't clean when the paint was applied. One of them had an electrical short upon installation which was popping my signal fuse. Luckily I had bought a spare. Installaton wasn't a big problem, but I wish they used thicker gauge of wire, it's very thin. Very inexpensive blinkers, but you get what you pay for. I wish I had spent a little more and gotten better quality blinkers. View detail

Difficulty in weather resistance

Why is it that everyone is so quick to exchange to NORMAL? I was wondering,
Now I know why. After about a year of storage under the eaves, the surface hardens.
ParisParis and tear it up. View detail

The weight of the description does not Ate.

OEM 3-type for horizontal JOG (480g) I bought it for the weight Up rather than the
The description gives a weight of 515g, but the actual measurement is only 496g.
OEMs usually increase or decrease by about 5g because of balance shaving, etc,
I could not think of writing an imprementation that I would recommend to others if the Cut-out Outer had an error of almost 20g!


[Regarding installation].
50cc horizontal JOG (3KJ/5AUCase before regulation, 5BM/5SUCase after regulation)
Case cover Gasket is required.
However, the shaft part is thicker than OEM, so when you stop the Nut, insert the O-ring, and try to close the Cover.
The gap with Bearing on the Cover will be insufficient.
So we need to take measures such as thinning the O-ring

・3WF
There's plenty of room to spare. o-ring should be as thin as the 50 story?
You can replace the Nut that stops the Outer with a thin Nut for 50cc View detail

Not good

It might be a little hard to see and I don't like it. View detail

Does not take into account the intent of Low Friction

Before use, the Advantage arrived in a bag with about 3 layers tied around it and very tight curvature.
It is partly bent and habitual, and although the product claims to be Super low friction, it is ruined by Advantage's packaging.
It does not seem to fully reflect the intent of the producer.
I would like to see Advantage improve the shipping conditions with a more gradual curvature.
WeBig is in the process of requesting a replacement. View detail

For Silencer protection

I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.
This time I bought it with the earnest desire not to add any more scratches to Silencer.

Installation is done by pulling as hard as you can on the Rubber loop.
It requires quite a few parents.

It is cool as a Design, and it Guard Silencer well as a Protector.

I was a little disappointed that it slides and moves when the light is actually turned on, and at first I was concerned about it and had to change the position of the outlet of the exhaust system every time. Recently, I have come to think that it is fine as long as it is on, and I use it as it is without fixing it.

I think it is difficult to increase the number of scratches on the Exhaust System.
I want to remove it when I get good at it. View detail

I failed.

When replacing the master cylinder, the stock switch box would give me more room for the gas pedal wire.
I bought it The wire is 800mm, and the inner pipe is 44mm without thinking.
This is the source of the mistake. There's no point in making it so high throttle in the first place.
I put it on and it's really high throttle, sweaty, and the gas pedal is really heavy. ・・・・
The wire also seemed a little long ・・・・
I think the balance with Rajpon is great, but maybe this time I made a mistake in choosing the right parts.
It's not an improvement, it's a deterioration.
I'd like to try it next time with a 35mm throttle and 700mm wire. View detail

Sleeves are too short.

The sleeves were 3cm too short and I returned them asap. I wonder what standard they are meeting.
I found another color at a special price, but the special price is non-returnable.
I chose this color and I'm glad I was able to return it.
I can't buy Wear's specials because I can't try them on. View detail

Even though it's only for car models ….

I purchased it specifically for my car model, but could not install it without modifications. View detail

Heart breaker！

First and foremost, we must note that the BALI in the cutting process is quite bad, and honestly, it is the Level that causes injury.
If it is a FOR JAPAN MODEL product, I think it is a hesitant Level to ship the product as it is.
And it is not very good as accuracy, and the Center axis is also blurred.
However, it does not mean that it cannot be used at all. If BALI is removed sesse-sese-sese and military gloves are used, it is not impossible to use it.
However, we do not anticipate that the product will be used many times, and we hope that you will consider it as a disposable level for this time.

Personally, I would urge everyone to choose a more solid product when considering it as a tool.
well ♪ Hyakkety-yak ♪ It is possible for people who understand the concept of "Level" to purchase the product. View detail

SV650Rear Brake Pads replacement

Rear Brake Pads on a 2022 SV650 were replaced.
I have driven about 100 km since the replacement and will post my impressions.
The OEM had about 9,000 km and it was time to replace the Rear Brake Pads, so we chose NTB for its good cost performance.
Operability is gentler than the OEM, and I felt that if I did not consciously step on it hard enough, it would not work as well as the OEM.
For those who prefer a gusto effect from the beginning, I think it will be less satisfying. View detail

Not Standard Size

25.2mm, so it will be sandwiched between the rubber plates.
However, Rubber sticks out, does not pinch properly, etc. Stress builds up subtly.
In the end, I managed to attach it, but I was not satisfied with the wobble, the subtle texture, and the fact that it was rather large for a skimmer Switch.
I think it would be better to use a 22mm size made by NAKA0 with waterproof and wiring processing...
Well, it's too much trouble to replace it, so I'll use it until it breaks. View detail

Durability may be difficult.

The ease of installation was a plus.
The battery stopped charging less than six months after installation.
According to Manufacturer, it was due to age and not covered by warranty.
I hoped it would be a little sturdier and last longer. View detail

Poor return of Engine Starter Motor

After a year and a half of use, the return of the Engine Starter Motor was poor and the CellMotor kept turning.
The same thing is written in the review of KIJIMA's Engine Stop Switch, so things seem to be the same.
For now, I did a Silicon spray and it came back, but I'm sure it will reappear after a while.
It is inexpensive, so let's just use it as such. (Laughter) View detail

Hmmm...

This is a replacement from OHLINS Grip, but the Fitting is poor.
It can be installed, but it does not feel right.
Is it expensive for the accuracy? View detail

poor response

The MASTER of the front brake was replaced with a type without a switch, so a hydraulic switch was used.
The Stop-lamp did not light up with a light pull, and finally lit up when I gripped it a little like a hard brake. View detail

It was too difficult for me.

I had experience pasting automotive film in the past, so I bought it thinking it would work, but it turned out to be disastrous.
The shape is complex and cannot be aligned well with subtle curved surfaces at all.
Moreover, it is difficult to remove air bubbles because of the thickness of the ??Film, and it is stretched so much that air bubbles do not come out at all.
It is wiser to be honest and ask the PRO to do this.
Sorry, this is a bit of a whiney impresario. Yes, the product is solid and looks good. View detail

SLASHSlider

Mounting holes were slightly misaligned. View detail

I was planning to tour at high speed, so I was hoping for a Handlebar shake effect.

I purchased this product because it was said to be compatible with my car model and year, but the included screws were too short and could not be installed.
Furthermore, upon closer inspection, there were also scratches.
It is a pity that the price was so high. View detail

Wiring branch connections are easy and good.

The differences in Cable size and current capacity are easy to recognize depending on the color.
Note that the Cover is divided between the main line side and the branch line side.

*Because the blade directly bites into the sheath for connection, use in locations with a lot of vibration may result in disconnection or poor contact.
*Care should be taken not to reuse the area once used.
It is easier said than done, since the connection can be made with just one pliers.... View detail