Reviews
Grip heater refill
I installed a replacement GH-10 that I had been using for 2 years, but it stopped working and during a Sale.
I was thinking of using something different, something made by DAYTONA or something with a separate controller, but I chose the GH-10 again because I thought the convenience of being able to operate it with a short push at hand could not be compensated for by the difference in price.
The Axel side is easy to install since it is integrated with the Throttle cone. The opposite side is difficult to install unless it is warmed up. Wiring is done by floating the Headlight in the back gap. It's still useful to have it from a little chilly season to winter.
View detail
Add on to Clamp on heated grips
Best bang for your buck, works ok, and i like it works/plugs in with clamp on heated grips! I have good luck with most all webike products. I purchased 1 of these along with the associated heated lock grips for my wife's and my bikes. Installation was straight forward after watching the videos. Just had a chance to try them out over winter break with temps around 10C - 15C. They took a few minutes to warm up, but did a great job. We typically started on a setting of 2 - 3, then turned them off after our riding activity increased. Very warm, even through our winter gloves. Great purchase, happy wife!Would recommend! Fast shipping as always too.Thank you Webike. View detail
Easy to install, better than ManufacturerOEM
The switch is integrated with the grips for easy installation, requiring only wiring and no effort.
It is also possible to point it straight up to avoid touching it when operating the blinker. If you warm up the Heater to the maximum Large setting, you can easily pull out the Grip.
The thickness is just right for general OEMSize and is a non-slip Material.
View detail
Fits: HONDA CB500X, YAMAHA YZF-R6, YAMAHA YZF-R3, YAMAHA YZF-R1, YAMAHA XSR900, YAMAHA XJR400 R, YAMAHA XJR1300 L, YAMAHA XJR1300, YAMAHA XJ6 Diversion, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-01, YAMAHA FZ-1 FAZER, YAMAHA FZ-1, YAMAHA FJR1300 AS, YAMAHA FJR1300 A, YAMAHA FJR1300, TRIUMPH BONNEVILLE, TRIUMPH TIGER 800 XRX, SUZUKI BANDIT 1250 S
Easy-to-use Motorcycle Cover
It is smooth and easy to use. It is just a little disappointing that there is no aperture so it is easy to get wound up. I think Y's Gear might be better in that area. View detail
Rust-resistant Material from OEM:Replace with Stainless Steel!
OEM is prone to rust, so we replaced it with this product.
Cap is also included.
Material:I thought about Titanium, but it's too expensive Material:Stainless Steel
Quantity because Front is Double disk.:Buy 3 for 1 Set for 1 Vehicle.
The OEM cap can be removed with a slotted screwdriver.
This is very hard to loosen and almost nappy.
The attached Cap is a Hexagonal Wrench for peace of mind.
View detail
Other Brand Product is also acceptable
I used to use oil filters made by other brand products such as Vesra, but when I switched to motorcycles, I chose DAYTONA and have been using them ever since.
It's not something that you can really feel the difference in performance, but since I started using it, I haven't had any problems with the Oil getting very dirty or leaking Oil, and I haven't had any problems with it.
If I had to point out one drawback, I would say that the Wrench (which snaps into place like a lid) for the OEMFilter is not quite right. Also, the pure black exterior makes it easy to see dirt.
View detail
very good. This is excellent in finish and quality
There were many subsidiary materials, so there was no difficulty in installing them, and I personally think the LED light is beautiful I'm willing to install it on my other bike. View detail
Already the third one.
Every time I change motorcycles, I install a new grip heater, but this heater is the only one I use. The heater remembers the last Level, so it keeps the temperature at the right level. View detail
Braking power up by 1SizeDown from OEMMASTER
The wife of the owner of the vehicle said that she was afraid of braking due to the 20-year-old OEM Master Cylinder, so we decided to replace the OEM MASTER Overhaul with this MASTER. I also wanted to increase the braking power by reducing the size from the Piston type, so I replaced it with the 11mm Piston type MASTER. (Quantity:Pair (for Left and Right) to 1/2-inches→11mm)
The smaller piston size of the Master Cylinder increases the braking force, but the amount of stroke increases, so a change of about 1 size is recommended.
The MAJESTYC I installed is my wife's Motorcycle, and she has a weak grip, so I had a request to make the Brake a little lighter.
The touch was good, and together with the 20 year old Brake hose, which was also changed to Stainless mesh, the Brake looks very nice.
My wife was relieved to hear that it was easier for her to ride as well.
View detail
It works goofily!
Used for front brake of XELVIS.
The No Brand pad that had been on the car up to that point was so ineffective that I had to throw it away, even though it was 8 parts high. In comparison, the brembo pads are very controllable, starting to work slowly in accordance with the lever-on force, and finally suppressing it with a strong force. I can now enjoy driving on mountain roads that I had been too scared to drive before.
The color of the Pad is bright Red. A sense of doing Good to get out. brembo's marking is written on the Pad and is clearly visible with a cantilevered Caliper. I have used OEM, Vesla, Red Pad, Golden Pad, etc., and this is the easiest pad to use without feeling insecure. The Fee Ring is similar to the Red Pad, but feels softer and tighter than the Red Pad.
The only thing that seems to be a drawback is the lifespan, which reaches its limit after about 5000 km. This is normal for a Pad, but for some reason the new Element was very thin (about 4mm?). The Pad with 40,000 km without replacement before the replacement had more left. If they made it thicker, it should have a longer life.
View detail
Fit like a dedicated Cover!
[How is it used?
Used at home Garage
Was the one you received as per Image?
Almost as shown in the Image, but somewhat flimsy impression
How was your experience with it?
CinderellaFit, as if it were exclusive to CL250!
Size was perfect.
View detail
I feel secure.
With more than OEMs, there is a sense of security. View detail
Wiring is Limit...in a way it fits.
This is the third KIJIMA Grip heater I have installed. The performance and cost performance are excellent, but the distance to the Right and Left Wiring connection points is short, and there is a fuse in that area, so I have to remove the tanketc. to get to it in case of emergency, which is a shortcoming.
The OEM grip for the CL500 is a type without a bar end, and this grip heater is compatible with this type, but this time I installed a Zita bar end plug, which fits well. The smallest part of the supplied throttle fits perfectly.
And when the Grip is aligned with the LeftHandlebar End, there will be a gap of about 3mm at the Handlebar Switch.
View detail
Stagnant when running!
As for the oil filter, I replace the element every time, even in motorcycles, instead of once every two times, just as I do with maintenance of vehicles. In my case, I don't like OEM products for consumable parts, so I look for better products among the compatible products.
# 2in1 Exhaust System is not cool and I don't want to buy it, so if Webig won't sell it to me, I guess I'll get rid of it.
View detail
Good looks
I bought a new GSX250R and replaced the tank with a new one, not because there was anything wrong with it, but because I wanted it to look good. I thought it would be cool if the tank was made Radial style. As others have said, when I tried to install the tank, the tank was a little askew and the position of the tank bracket was not quite right. I was disappointed in this point. The installation was easy. View detail
Easy to control
I use this Repeater on my Honda 400X. It is not very effective, but the Touch Fee Ring is very easy to control. I use it for my daily commute and it is easy to use in all weathers and traffic jams. I replaced it after 2.5 years with the OEM and replaced it after 1.5 years with this product. This time I felt that there was a little bit of BALI on the end face of the product, so I removed the BALI on the end face with File. (Is there a slight variation in quality from lot to lot?) View detail
The Cover is perfectly effective even in the rain!
[How is it used?
It is being used on a 2019 Z900.
Purchase Size is LL. usually kept on the only rear.Maintenance Stand is hung.
Was the one you received as per Image?
It is thicker than Image, and my expectations were high that it would be very effective as a Cover the moment I picked it up.
I used to use a non-WaterRegisterance product from the company Cover, but the thickness is noticeably different from that.
How was your experience with it?
I hung the Cover as soon as I received it, and it blocks the sunlight normally without any problems on sunny days.
We were lucky enough to have rain the next two days, so we checked the effect on the car body after the rain stopped, but there was no effect at all inside, and the Waterproof performance was well demonstrated.
Also, since the LLSize is relatively large, even if the maintenance stand was applied to make it taller, it would cover the bottom so that the Wheel would not stick out and get dirty.
The center is also equipped with a belt, so the Cover does not flap around and protects the vehicle body.
[Points to note]
It may or may not be important to note that the Heat Seat can be applied to the area where the Exhaust System hits, but it will not be effective at all if it is applied to the right place, so we recommend that you check the location carefully before applying it.
How did it compare to other products?
The price is higher than the regular Cover made by the company, but considering the waterproof aspect, I think I will repeat this in the future.
What is the rest of the useful life? I guess.
View detail
Luxury Up
I think the weight of the system reduces vibration a little bit.
I like the design.
View detail
Made by DAYTONA, which is inexpensive and reliable
The Oil Filter is replaced regularly, so the low cost is very helpful.
We have also used this product in the past and have been satisfied with its performance.
View detail
Thank you for your quick response!
It was very worn, so I had to replace it as soon as possible….
I ordered the product and got it sooner than I expected.
Thank you for your quick response.
View detail