Reviews
Purchased wrong size
I bought the wrong size. I'm thinking of buying it again. View detail
Fits: SUZUKI GSR250, SUZUKI GSR400, SUZUKI GSX1400, SUZUKI GLADIUS650400, SUZUKI GSX-S1000F, SUZUKI SV650, SUZUKI V-STROAM250, SUZUKI V-STROAM650XT, SUZUKI V-STROAM650, SUZUKI V-STROAM1050DE, SUZUKI V-STROAM1050XT, SUZUKI V-STROAM1050, SUZUKI GSX-S1000GT, SUZUKI GSX-R1000R, SUZUKI GSX250R, SUZUKI BURGMAN400, SUZUKI V-STROAM, SUZUKI GSX-S1000S, SUZUKI GSX-S1000
Purchased for ja59
I bought this to install on my JA59, but the OEM Handlebar could not be installed.
I was going to replace the OEM Bar End with a shorter Handlebar width, but this time I got a disappointing result!
However, I am satisfied with the quality of the product and will keep it in stock until I install it on another motorcycle.
View detail
On a 2011 CBR600RR.
I bought it because I didn't want to do thick Gloves in the winter.
The installation was done by Webike's Support store with direct shipping.
In the case of the CBR600RR, I gave up on it myself because it is Large strange to remove the FI side of the Accelerator Wire.
I have used it and it heats up so much that it is hot at the strongest Level.
My wish to use thin Gloves in winter was fulfilled as long as I warmed the back side of my hand from time to time.
There is no possibility of mishandling during Blinker operation.
View detail
Good Brake Pads
Very good Control. Durable and reliable. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
Better than OEM
Replaced because OEM is too hard to see. Installation was easy. I can't say how visible the OffsetHolder is since it was replaced at the same time, but it is more visible than the NORMAL. View detail
Designed to fit any motorbike, with a luxurious and sporty look and feel.
The mirror looks like anodox round mirror, but the combination of aluminum and carbon gives it a luxurious and sporty appearance.
Looks good on a variety of Motorcycles
I was a little worried that the mirror surface might be too small. I was a little worried that the mirror surface might be too small, but it seems to be slightly convex, so when I actually drive the car, I don't feel that much of an invisible stress.
View detail
KIJIMAGrip heaterGH08Push Switch
It's been about two weeks since I installed it and so far no problems.
The Grip is a little thicker than I expected, but it is just right for me. I was thinking that I would mishandle the Switch if I used the type attached to the Grip, so I chose this type, and it was the right choice. It is easy to operate and I feel it is convenient to attach it anywhere I want. Also, my palms are quite warm if it is 4 degrees Celsius in the morning and the temperature is at the maximum. But only my fingertips are hard to keep warm. If you want to keep it on all the time, I think the 3rd or 4th of 5 levels would be best. I think the 3rd or 4th out of 5 levels would be best if you want to wear it all the time.
Electrothermal Gloves or Inner Electrothermal Gloves (You will need to bring your own Gloves separately) Would it be good to have a And.
With the skin Gloves with boa, the palms will feel sweaty.
View detail
Two years of use and still Large sturdy!
I used it on another vehicle with Blue empty parking for 2 years and it has worked fine with no problems except for some ragged loosening and fading of the fibrous material around the key for hole, so I bought a Repeat!
It is also useful for the Motorcycle body as it does not scratch easily!
I don't know because I have not used it in a dusty or sandy environment, but it works fine in an environment with Concrete and Asphalt floors.
View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
grown-up (man)
Replaced OEM for better rear visibility. View detail
Fits: SUZUKI GSR250, SUZUKI GSR400, SUZUKI GSX1400, SUZUKI GLADIUS650400, SUZUKI GSX-S1000F, SUZUKI SV650, SUZUKI V-STROAM250, SUZUKI V-STROAM650XT, SUZUKI V-STROAM650, SUZUKI GSX-S1000GT, SUZUKI V-STROAM1050DE, SUZUKI V-STROAM1050XT, SUZUKI V-STROAM1050, SUZUKI GSX-R1000R, SUZUKI GSX250R, SUZUKI BURGMAN400, SUZUKI GSX-S1000S, SUZUKI V-STROAM, SUZUKI GSX-S1000
I'll think about it a lot.
This is the first time I have installed an UltraHeavy weight Bar End.
I thought the heavier weight would reduce vibration….
I have only ridden it a little bit, but it doesn't seem to vibrate.
I don't know how it will look when I get on the highway, but I wonder if it will be Large sturdy?
However, since it is heavy and large, it is thicker than the Handlebar, and I feel uncomfortable when driving it where it is different from the Handlebar.
The handlebar has been replaced with a handlebar that is up and narrower than the OEM handlebar, so I feel that the weight of the bar end sharpens the cutting angle when turning.
I hope I can get used to it and stop worrying about it, but if it bothers me a little, I will consider replacing it.
View detail
Fits: SUZUKI KATANA, HONDA VTR1000F, HONDA VT400S, HONDA VT750S, HONDA DN-01, HONDA Integra, HONDA FUSION, HONDA Silver wingGT400, HONDA Silver wingGT600, HONDA CBR 650R, HONDA CBR 1000RR, HONDA CB 650R, HONDA CB 1000R, HONDA CB1300 SUPER FOUR, HONDA NC750X, HONDA NT1100, HONDA VFR800X, HONDA VRX Roadster, HONDA FORESIGHTEX, HONDA 400X
sv650 is 2L
I bought a L because the fit guarantee said L, but when I put it on, it was BitchBitch's tight-fitting.
It took a while but they accepted the return and repurchased the 2L.
Easy to detach and attach.
Rain does not soak through.
It certainly does not dissolve when attached immediately after an Engine stop.
Good
View detail
Fits: SUZUKI KATANA, HONDA VTR1000F, HONDA VT400S, HONDA VT750S, HONDA DN-01, HONDA Integra, HONDA FUSION, HONDA Silver wingGT400, HONDA Silver wingGT600, HONDA CBR 650R, HONDA CBR 1000RR, HONDA CB 650R, HONDA CB 1000R, HONDA CB1300 SUPER FOUR, HONDA NC750X, HONDA NT1100, HONDA VFR800X, HONDA VRX Roadster, HONDA FORESIGHTEX, HONDA 400X
Ease of use is the best
Can be used immediately after returning from touring.
Easy to install and remove
I was looking for a product that satisfied the above two points and found one that looked just right, so I popped it in.
From the results, I'm really glad I bought it.
It is very easy to put on and take off, the cloth is firm, and I am very satisfied. It is a bit pricey, but if you think you can use it for a long time without Stress, it is rather cheap…?
I bought it when I bought a new Motorcycle, but I wish I had bought it sooner.
View detail
Absolute safety and reliability
D Type on ADDRESSV125 (with a twist) Banjo bolt is K9 (L3=Last model V125) Using OEM, copper Crash washer is 1.5mm thick.
It works well.
Gyuin! and stop.
(I'm not going to put Brake on it and go through the slushy.)
It is made of one piece of steel and is simple to use. There is no possibility of malfunction or failure due to installation errors. Furthermore, it is less than half the price of other companies' products, so there is no other choice but to buy it.
OEMBanjo bolt is made of steel and is Material in case of a fall:It is absolutely safe because it does not crack like aluminum. The banjo part of this product is 8mm thick and the OEM brake hose is 10mm thick. (hole) The orifice position on the banjo was checked to make sure that the orifice position was aligned with the position of the K7 OEMBER bolt. The K7 OEMBE banjo bolt had the orifice positioned a little higher, with a 1mm crash washer on the bolt head side and a 1.5mm crash washer on the caliper side, and the orifice position was perfectly aligned. The bolt length is also perfectly aligned without any collision.
The Goodridge banjo bolt is made of steel, has a low head and good parenthesis, but when I went to see the actual product, I found that the OEM bolt works harder and faster with a little grip because the orifice diameter is twice as large as the ADDRESSV125 OEMB banjo bolt and the brake fluid volume is larger. The OEM brake hose is stronger and faster than the ADDRESSV125OEMBanjo bolt because it discharges more brake fluid. Furthermore, the orifice diameter of the mesh brake hose was also the same. Of course, the limit of the brake hose is the same for both the OEM brake hose and the mesh brake hose, but you can precisely adjust the brake effect according to your grip, and since the hose is not inflated by the pressure, the brake can be applied to the maximum large limit, which means that the brake effect is better.
FTire is IRC MBR740 DIX-RR with high grip. if the Brake works but the tire does not grip, it will slip. The order is to use high grip tire first, then change Hose and Pad.
Was the installation difficult?
This is a difficult category. I did a lot of research beforehand and measured the length of the ADDRESSV125 OEMHose to be 875mm, and the next setting is 850mm after the 900mm length. 900mm is definitely not pulling on the Hose, although it is a little dubby in the front cowl. We also put it through the OEM Guide and Rubber. This is the most important security component, so take your time and be careful.
How was your experience with it?
The best. Outstanding reliability. Hyper Sintered Pads, but they work so well that I thought they had been replaced by Golden Pads! Hyper Sintered Pads, but they work so well that I think they have been replaced by Golden Pads! (works fast). 。
Golden pad and high grip tires are also available.
[Was there anything that disappointed you?
No. I can't help but think that DAYTONA is a good company! I'm sure you will agree with me.
It doesn't matter if it looks tacky or not. Performance supremacy.
Very nice product, thank you.
View detail
Grip heater refill
I installed a replacement GH-10 that I had been using for 2 years, but it stopped working and during a Sale.
I was thinking of using something different, something made by DAYTONA or something with a separate controller, but I chose the GH-10 again because I thought the convenience of being able to operate it with a short push at hand could not be compensated for by the difference in price.
The Axel side is easy to install since it is integrated with the Throttle cone. The opposite side is difficult to install unless it is warmed up. Wiring is done by floating the Headlight in the back gap. It's still useful to have it from a little chilly season to winter.
View detail
Large change
LargeThey are solid, and most importantly, they have a waterproof feature, which is great. I chose the size by referring to the size chart. I have done so in the past, but I tended to buy a Large size because I was worried about it. If I did so, all the lower part of the cover would be on the ground, and it would be difficult to put the cover on and take it off. Moreover, the cover itself gets dirty. This time, I chose a size a little longer than the overall length of my motorcycle, so it was just right. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
Wider.
Good because the range is wider than OEM View detail
Add on to Clamp on heated grips
Best bang for your buck, works ok, and i like it works/plugs in with clamp on heated grips! I have good luck with most all webike products. I purchased 1 of these along with the associated heated lock grips for my wife's and my bikes. Installation was straight forward after watching the videos. Just had a chance to try them out over winter break with temps around 10C - 15C. They took a few minutes to warm up, but did a great job. We typically started on a setting of 2 - 3, then turned them off after our riding activity increased. Very warm, even through our winter gloves. Great purchase, happy wife!Would recommend! Fast shipping as always too.Thank you Webike. View detail
Easy to install, better than ManufacturerOEM
The switch is integrated with the grips for easy installation, requiring only wiring and no effort.
It is also possible to point it straight up to avoid touching it when operating the blinker. If you warm up the Heater to the maximum Large setting, you can easily pull out the Grip.
The thickness is just right for general OEMSize and is a non-slip Material.
View detail
Fits: HONDA CB500X, YAMAHA YZF-R6, YAMAHA YZF-R3, YAMAHA YZF-R1, YAMAHA XSR900, YAMAHA XJR400 R, YAMAHA XJR1300 L, YAMAHA XJR1300, YAMAHA XJ6 Diversion, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-01, YAMAHA FZ-1 FAZER, YAMAHA FZ-1, YAMAHA FJR1300 AS, YAMAHA FJR1300 A, YAMAHA FJR1300, TRIUMPH BONNEVILLE, TRIUMPH TIGER 800 XRX, SUZUKI BANDIT 1250 S
Easy-to-use Motorcycle Cover
It is smooth and easy to use. It is just a little disappointing that there is no aperture so it is easy to get wound up. I think Y's Gear might be better in that area. View detail
Rust-resistant Material from OEM:Replace with Stainless Steel!
OEM is prone to rust, so we replaced it with this product.
Cap is also included.
Material:I thought about Titanium, but it's too expensive Material:Stainless Steel
Quantity because Front is Double disk.:Buy 3 for 1 Set for 1 Vehicle.
The OEM cap can be removed with a slotted screwdriver.
This is very hard to loosen and almost nappy.
The attached Cap is a Hexagonal Wrench for peace of mind.
View detail