Original Japan Daytona x Nissin 14mm axial . Took 3 days to arrive to Singapore from mailing date .

Easy bleeding during installation . Upgraded from 11mm to 14mm axial. Love the lever feels. Installed on Yamaha Vixion-R 155 . View detail

The size is just right and the texture is good.

Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner. View detail

Blue empty parking.

Used for DUCATI 996.
I bought this because I am renting and park Blue empty, but I never want to let it rust because it is a rare car.
The rainy season is absolutely RECOMMENDATION.
It also has a hole for a lock, which is a little expensive, but it is a must-recommendation for those who park Blue empty. View detail

Does not fit the KL250 Sherpa.

The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.

KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.

If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.

Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!

I bought it + even processed it so I'll be using it for a while lol. View detail

Black still seems to be vulnerable.

Used outdoors in full sun for less than 1 year and 2 months after purchase.
What was originally Black has faded and turned gray.
It also tore like a rip, so I had to use curing Tape to plug the hole for now. Is it still susceptible to deterioration by sunlight if it is Black?
I am using two more in parallel, Black and Silver. the Black is about a year old. It has faded a bit but still seems to stand up to the test.
I thought I was using them the same way, but I am wondering how a difference of two months can make such a difference.
Silver is about 5 months old. It is still clean.
I was lucky that the exhaust pipe was not touched.
Since the original price is over $8,000, it would be nice to have a little more durability. However, the Motorcycle Cover is a consumable item. However, Motorcycle Covers are consumable items, so I am not that dissatisfied with them since they cost around 4,000 yen at Sale and I prefer black. But I think I will get the Silver color next time. View detail

It looks better now.

I put it on because it stands out from the OEM. View detail

Good variety of color variations

Standard NGKPower cable, used for CUB.
Speaking of NGK, I had always thought of Red and BlueCable images, but I was surprised to find that NGK has a wide variety of color variations.
I was curious about the Yellow color code + BlackCap, so I bought it, and the actual color was a nice bi-Bit color as well. View detail

Enhanced Ignition

Used for CB250. The installation pitch is the same, and it was possible to install without difficulty by bending the terminals.
The polarity is indicated at the base of the terminal, although the color of the Wiring is different.
Coupler, or simply throw away the entire Wiring and change it to a terminal.
As long as the points are properly adjusted, ignition timing adjusted, and condenser inspected,
Sparks are stronger and better.

I am looking forward to the durability of the rest. View detail

Overhaul around the Front of GT380

The front fork of my GT380 was leaking oil due to a point rust, so I thought about re-plating and other things, and decided that this product would be good in terms of cost performance.
There seemed to be no particular difference compared to the OEM.
We are very grateful to Large for releasing discontinued parts like this. View detail

Gone.

Within a month of using it, the wind blew it away. I only had to put it on and wrap one band around it, so when I came home on a windy day, only the band was left and the Motorcycle was completely naked. View detail

ALCAN hands iGrip

I have used it for VTR250 and MT-03, and I bought it again this time. The color is Orange red to match the body color, and it is a good accent for the handlebar. When I installed it, I used a small amount of glue to prevent shifting and decided not to use wiring. View detail

UV sensitive, torn after one year.

The 2LSize is too small for the MT09. Also, it seems to be weak against ultraviolet rays, and the part that was exposed to the sun well deteriorated and tore after not lasting a year. View detail

A little short.

I selected it from the vehicle compatibility chart, but the Rear is covered well, but the Front is not covered enough. I can compromise because I use it in a covered parking lot, but it is hard to lock the chain lock. It was a little more.
The texture of the Cover is good. As mentioned above, it is roofed, so I don't think it will be water repellent or strong, but I think it will keep for a long time. View detail

I wanted Cap.

I purchased this product to connect to the Ignition coil in Mukawa and wanted to unify the colors.
Cutter off the adhesive bonding the Cap to the cord, peel off the Cable outer skin of the Mukawa Ignition coil, insert it, and fix it with adhesive, and you are done.

The excess Cable of the product in question is used in place of the Cable attached to the OEMCoil.

This would have been unnecessary if caps in a variety of colors were available, but they are not.

Even if only the cable is replaced, the idling is stabilized and the long-used OEM product is refreshed. View detail

Size did not fit….

I bought the same DAYTONA made WaterRegisterntLight when I delivered my motorcycle, but I bought a 3LL because I misunderstood the size chart and it was a little bit Oversized around the Rear.

I bought the LL size after looking at the compatibility chart, but it's a Small size.
Although it is cheaper than WaterRegisterntLight, it is a bit peLePera and unreliable, and the anti-flap Belt is not sewn onto the Cover. (It is included, but it is a separate part.) Inconvenience.

One of my colleagues at work is a motorcycle rider, so I gave it to him for free.

I was actually going to buy LLSize's WaterRegisterntLight, but they were out of stock, so it was somewhat less damaging in terms of Gold amount. (Lol)
Now we will make the WaterRegisterntLight in the size we purchased last time. View detail

Power cable & elect. module Dev'moto

Bonjour from France Thanks you for quick shipment of my order , i fixed it on ma yam sr 125 in addition of a new electronic module Dev'moto(made in France) with an iriduin plug already than replace the TCI -dead-:( the result is more better ( already too with the new module) cold cranking + little better torque at low rpm, and more i could reduce my idle setting ... so very happy with my purchase ... voilà ! View detail

good choice

I bought it after seeing a review that you often replace it with a set with Takegawa reinforced coil. I bought any color because it was hidden in a cowl, and I connected the ngk power cable with the Takegawa reinforced coil and installed it. I had to cut the length and install it, but I thought there would be some loss, so I just connected it. It starts up well and I think it's effective in output. Thank you. View detail

Fit like a dedicated Cover!

[How is it used?
Used at home Garage

Was the one you received as per Image?
Almost as shown in the Image, but somewhat flimsy impression

How was your experience with it?
CinderellaFit, as if it were exclusive to CL250!
Size was perfect. View detail

affordable price for good quality product

these item is very useful for those who want to get perfect spark for the bike - the Cables are designed for the serious racing enthusiast and feature high temperature silicone outer jackets, solid copper wire strand core and high temperature resistor covers, leading to improved engine performance View detail

The Cover is perfectly effective even in the rain!

[How is it used?
It is being used on a 2019 Z900.
Purchase Size is LL. usually kept on the only rear.Maintenance Stand is hung.

Was the one you received as per Image?
It is thicker than Image, and my expectations were high that it would be very effective as a Cover the moment I picked it up.
I used to use a non-WaterRegisterance product from the company Cover, but the thickness is noticeably different from that.

How was your experience with it?
I hung the Cover as soon as I received it, and it blocks the sunlight normally without any problems on sunny days.
We were lucky enough to have rain the next two days, so we checked the effect on the car body after the rain stopped, but there was no effect at all inside, and the Waterproof performance was well demonstrated.
Also, since the LLSize is relatively large, even if the maintenance stand was applied to make it taller, it would cover the bottom so that the Wheel would not stick out and get dirty.
The center is also equipped with a belt, so the Cover does not flap around and protects the vehicle body.

[Points to note]
It may or may not be important to note that the Heat Seat can be applied to the area where the Exhaust System hits, but it will not be effective at all if it is applied to the right place, so we recommend that you check the location carefully before applying it.

How did it compare to other products?
The price is higher than the regular Cover made by the company, but considering the waterproof aspect, I think I will repeat this in the future.
What is the rest of the useful life? I guess. View detail