Not for installation on MULTISTRADA 1100SOEMWheel

I purchased the OEMWheel for the HYPERMOTARD 1100S to install on the MULTISTRADA 1100S.
The wheels are interchangeable, but the brake rotor cannot be used due to its different diameter. If this Disc Rotor is used, the Offset will fit perfectly. The compatibility chart shows MULTISTRADA 1100S, but it cannot be installed on OEM wheels.
It took a long time to arrive, but I am highly satisfied. View detail

It's probably for the best.

Everything is in balance.
There is no uncertainty whatsoever. View detail

Oil change essentials

[How is it used?
PCX125 JF56
Purchased for oilfor replacement of CBR600RR PC40.
I was looking for something with a small number of pieces to go home on the Net, and since it was a DAYTONA product, I bought it.

How was your experience with it?
It is like a normal Washer.
I used it when I changed the oil and the fit with the drain bolt was perfect.
After replacing the oil, I have been able to use it without any problems, including no leaks.
I will purchase again next time.
How did it compare to other products?

[Points to note]

Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer View detail

Good design. However, the hexagonal hole is delicate.

Coloring and design are both cool and satisfactory.
However, it should not be used for frequent removal/attachment, as the hole slips easily due to the aluminum material and 3mm hexagonal hole, which is designed to emphasize design.
If there is a lot of removal and installation, I personally recommend Ducabike with 4mm hex holes. View detail

I use it all the time.

I feel safe and always use them. View detail

Not just fitSize, but no problem.

It was used when Oil was replaced in May 2023. Gasket removed at this time. (used by a familiar Dealer). The outer diameter of the "Gasket" is φ20mm, which is larger than the outer diameter of the "Drain bolt" (about φ19mm?). The inside diameter is also larger than the drain hole on the crankcase side, and there is a recess in the shape of the drain bolt left in the gasket. The inside diameter was also larger than the drain hole on the crankcase side, leaving a convex shape in the form of a drain hole, which is evidence that the Gasket was properly deformed and fulfilled its packing role.
The Daytona Gasket I purchased this time has an outer diameter of φ18mm, which is smaller than the outer diameter of the drain bolt, so I am a little worried about whether the tightening strength per area will be too much, but aluminum is soft and easily crushed, so this is about the same size as the Torque. (25N-m) Crankcase at (possibly made by Casting Iron?). The side will not be deformed.
I drove it as fast as I could for about 100 km after the replacement and about 250 km after that, including after that, until I gave it away in February 2024 at 8038 km, and there was no Oil leak. It is functioning properly. View detail

Stable braking powerGolden Padχ.

I am not looking for an absolute increase in braking power, but since I use the RRBrake a lot, I feel that it heats up and wears out quickly. I've chosen Sintered padGoldenχ which is highly resistant to fading, and the control is not bad. View detail

The color of the color insert that can be glimpsed is Race ish.

I did not choose the rear brake because of its effectiveness, but because I am a brembo believer.
I liked it because of its brembo-like Controllable nature.
I like the vermilion color of the back plate because it creates a race-ish atmosphere.
Since it is a rear brake, durability also depends on the individual, but it seems to work for a long time.
Since the bite is not attached immediately after replacement, you may feel a lack of potency, so pad break-in is a must.
I have not used this Pad in Circuit yet, but it is easy to use in OEM same etc. View detail

Raise the mood!

[How is it used?
Both for Brake and for Clutch are used.
Was the one you received as per Image?
No change from previously purchased items.
Was the installation difficult?
Easy installation by simply aligning the slit with the Arm section.
How was your experience with it?
The atmosphere is changed compared to the standard condition.
[Included Parts:were they on?
Included Parts:are not available.
[Was there anything that disappointed you?
A little more durability would be nice. View detail

BremboOEM Product

Reliable Brembo OEM.
No complaints for Touring use.
CC Type (Blue color) I personally found this one easier to Control. View detail

I'm going to be honest with you.

To be honest, I have not yet installed it.
Since actual use is still about six months away, I will write my impressions first.
So, the evaluation is a prediction.

We began by gathering information from various sources before making the purchase.
After all, brembo is installed as OEM, but there is no information on JapanFOR JAPAN MODEL.
I asked the Shop in Italy and received an immediate response, and then asked the Japan distributor to confirm the answer.
PLOT." The lousy reply is that there is nothing that fits in a store called
for "Koken" I received a very detailed explanation from Mr. Kato, who was so kind that I was bowled over.

According to the report, this SA has better performance than the OEM, so we decided to purchase it.
For OEM Product, the end is a number and OEMOption is AlphaBed.
Italy recommended SR's RACING, but I decided against it because it seemed to wear out too quickly.
I was informed by webike that I could get a fit, so that's how I decided to buy it.
However, my wife reported that it arrived with a sound of rattling, and when she opened the package, she found that it was just as shown in the picture.
The packaging was a little more careful than I would have liked, as the pad was placed in a box with a small shock-absorbing cushion on top. View detail

Reasonable and easier to handle than OEM

I always use this product when changing oils and fats.
It has a Wrench-enabled head on the end, so it is easy to attach and detach, and despite the fact that it is almost functionally the same, the price is lower than OEM, so it is very useful.

The OEM was Stress because removal could not be done without destroying it, but after switching to this one, there is no extra process.

The Wiring hole is another thing I like about Race ish. View detail

Genine Brembo Rear Brake Pad SP Compound

This was a set that I needed to replace the pnes I previously had in the bike. I wanted to try and match the rears with the front but not quite as agressive for the rear as it is not used that much on a track day. Not hard to find the right pads for the rear caliper, it's a Brembo 2 pot version, pretty standard. I used the tools Webike provide and then cross referenced with Brembo website for my own peace of mind. I had a few other parts in my order including the RC front pads which I was matching with. Because I combine some of my parts into one order, the cost of shipping is a lot cheaper than getting them individually. EMS is who I use these days as they just get the job done fast and efficiently. My order arrived in 5 days from Webike warehouse sending my order. What's not to love about that. The pads came in a Brembo packet and aslo Webike secured them in a bubble wrapping for safety and to keep my other parts safe from damage in transit. These pads are a road compound but are plenty for a track day as I personally do not use the back brake a lot anyway. They had a good matieral on the pad, plenty of meat on there for sure. They performed very well even though the conditions on the day weakened as the day went on. I was still very impressed with the pads anyway. Great work Webike, very pleased with this purchase. View detail

Genuine Brembo Brake Pads for Brembo 4 pot caliper.

I had a customer in who had upgraded their calipers to some nice Brembo ones but then they needed some new pads. As they did not know what pad code they needed it was pretty easy to find the right ones for the caliper they had. Standard 4 pots. After I knew the part numbers, finding them on Webike was super simple. Just type in the code and away you go. The price was really good from Webike and combined with some other parts in my order, I had them all shipped together to save on shipping separately. I got all my order in 100% perfect condtion in 5 days from shipping. The pads already come in the Brembo packets wqhich do actually protect the pads from damage and debris gettin inside which could contaminate the pad material. Really good pads, you can see the sinter material by just looking at them. There was no debris of excess pad materieal inside the packet which is always a good sign. Once you get them a few 100 miles in, the pads just get better and better. Brilliant purchase. View detail

It usually works.

Since the brake disc rotor was replaced with a new one, we also replaced the brake pads with new ones as per the CAUTION of the disc rotor.
We were not looking for a significantly higher coefficient of friction or increased braking force than the OEMPad.
The DAYTONAHyper Sintered Pads, as the package claims, are hard to lose, long-lasting, and effective, with the same features as OEM pads, which is exactly the specifications we were looking for.
It looks simple, like an OEM product, and does not feel uncomfortable when installed on the car body. In my opinion, it is a just fit.
Of course, we do not intend to deny the higher grade Pad made by DAYTONA, and the ability to choose Brake Pads with the specifications required by the User is rather Large welcome.
I don't think there is anyone in Waebig who neglects maintenance of the brake itself, but I believe that the brake performance can be normally demonstrated only when the brake caliper is cleaned and maintained on a regular basis.
If you're feeling nervous, why don't you try Brake Maintenance for your car? View detail

Easy to install, recommended for beginners

It could be used in the same way as OEM Product.
The product is highly accurate and there were no oil leaks, etc.
Brand-wise, I trust and recommend it. View detail

Normal good

It works normally
It was Large sturdy, popped on without doing anything in particular.
It doesn't squeak and it usually works.
I thought the Red color insert was kind of nice. View detail

YOSHIMURA collaboration is the best!

Used on Ducati Deer Bell 1260s.
Since we were replacing the Oil, it was time to replace the OEMOil Filter that had been used since new.
At first, I still thought OEM was the way to go, but when I looked into it, to my surprise, the delivery time was too long, so I started looking on Webike to see if there were any other compatible products available. In the end, I could only find the ones from other Manufacturers and not ours. （I wonder why they didn't find ours.

I checked the official K&A website and found no products that fit this 1260, but I found KN-153 that fits the old model, so I bought it as a trial and installed it successfully. I bought it as a trial and installed it successfully!

By the way, I am super happy because it also comes with a YOSHIMURA Sticker! View detail

Great looks. as a cap bolt….

Do not over-tighten or apply Screw lock agent by mistake, as the material is material and will quickly lick the hex holes.
I want to install it firmly because it is for fixing Stay which supports important parts around Handlebar …. View detail

Pad not necessary for most people.

It works with considerable gusto from the initial grip.
The Fork sinks down from the beginning, so it will be difficult to ride on other than a sports type motorbike.

There is no need for a pad that works so well from the start, and it is not recommended for general use because it will change the movement of the Fork and alter the characteristics of the Motorcycle.

I think there are more people who run Circuit on SUPER SPORTS750 to Main and Demerit who use it outside of competitions such as Gymkhana.

I think this pad is popular because it's cheap and easy to understand how it works, but it's like cheap, flavorful food, like junk Hood, as an analogy, and it's tempting to jump on it, but it's really not a good thing. View detail