Reviews
Fits: YAMAHA SR250(ALL MODEL), YAMAHA SR125(ALL MODEL), YAMAHA SR400(ALL MODEL), YAMAHA TW200(ALL MODEL), YAMAHA TW125(ALL MODEL), YAMAHA TT250R Raid(ALL MODEL), YAMAHA TT-R250(ALL MODEL), YAMAHA TDR50(ALL MODEL), YAMAHA TDR250(ALL MODEL), YAMAHA TDR125(ALL MODEL), YAMAHA TDM900(ALL MODEL), YAMAHA TDM850(ALL MODEL), YAMAHA SRX250(ALL MODEL), YAMAHA SRV250(ALL MODEL), YAMAHA TW200E(ALL MODEL), YAMAHA TW225(ALL MODEL), YAMAHA TZr250R(ALL MODEL), YAMAHA VINO(ALL MODEL), YAMAHA WR250R(ALL MODEL), YAMAHA VOX(ALL MODEL)
It's a little hard.
The texture was good and the grip felt good, but...
I'll preface this by saying it's not bad. However, because my hand is a little small, Lever operation became distant and there was a sense of discomfort.
Also, it's harder than the Pro grip I've been using, so my palm hurts when I use it for a long time.
I'm an old man now, so if you're a young man with relatively big hands, you might have no complaints about this product. (Lol)
View detail
![Pilot Jet (Slow Jet) [for KEIHIN PWK28/PE24]](https://global.webike-cdn.net/photo/impression/6b/6b597ac373b3516ce7c9a68ba65854ebL.jpg)
Fits: HONDA STEED400, KAWASAKI KDX125/SR, HONDA BROS650, HONDA BROS400, HONDA XELVIS, HONDA BROS400, HONDA STEED400 VSE, HONDA STEED600, HONDA XLR250, HONDA STEED400, HONDA STEED400, HONDA XLR250, HONDA XLR250, KAWASAKI KDX200SR, HONDA XLR250, HONDA XLR200, KAWASAKI KDX220SR, HONDA XLR125R, HONDA VT250 SPADA, HONDA VT250 INTEGRA
It is indeed made by KEIHIN.
It is indeed made by KEIHIN.
I have no complaints.
Webig has a lot of stock, which is great.
We never use Jet products of unknown manufacturer.
View detail
Fits: HONDA CM400, HONDA CM250, HONDA CB400T CB250N, HONDA VT250Z E (85), HONDA SLASH N-IV 92, HONDA SLASH N-III 92, HONDA VT250 SPADA, HONDA GL400YAMAHA Super JOGZr Wing Black, HONDA CBX550 F/INTEGRA, HONDA XELVIS, HONDA CB400 SUPERHAWKIII CB400D, HONDA XELVIS, HONDA CB400 SUPERHAWKIII CB400D, HONDA CB400 SUPERHAWKIII CB400D, HONDA CB400 SUPERHAWKIII CB400D, HONDA JADE, HONDA JADE, HONDA JADE, HONDA MAGNA(V-TWIN MAGNA), HONDA MAGNA(V-TWIN MAGNA)
Peace of mind that you can easily replace the trusted with MagnetOil Filter!
I think it is difficult to evaluate the performance and efficacy of ☆Filter.
☆ Because it depends on the performance of the OIL to be replaced and its frequency.
☆ But with Magnet is available at Reasonable price!
You can buy with Magnet at half the price of OEM Product without Magnet.
☆ You should be able to buy it along with other essentials and get free shipping, so don't hesitate to exchange it.
Because ・・・・・
↓
I'm sorry, but I can't do anything about it. (Sweat)
I thought I was only doing OilMaintenance properly...
I thought I was using high grade and high count oil and replacing it frequently, but…
It is spoiled by the good condition of GunGun spinning with silky oil...
I've been enjoying the full throttle acceleration at 14,000 rpm almost every day since I started riding;
I was underestimating the strength of the Engine Displacement Volume....
I wrote about this in my Gasoline additive impressions.
A company's ability to protect Oil is also there, but Oil contamination by additives might have been Large.
Engine flushing is not a normal thing, but from my experience with hard OEM oil, I thought it would be easier to get used to it if I left a little bit of the previous oil;
Well, the bigger your car is, and the higher the performance of your car is, the more often you need to maintain your oil and filter! I think it is good to be nervous about it. ( By the way, it seems that I was too much spoiled by the reputation of the sturdy Engine, or relied only on the mileage, and missed the Oil's blackness...sweat)
Moral of the story:If you want to run a high performance engine on a large scale, don't spare the time and effort to change the oil and filter!
View detail
Fits: HONDA XR100, HONDA XR100, HONDA XR50, HONDA XR50, YAMAHA FZ-6S, YAMAHA Lanza., YAMAHA Lanza., YAMAHA TZR50R, YAMAHA TZM50R, YAMAHA TT250R Raid, YAMAHA TT250R Raid, YAMAHA TT250R, YAMAHA TT250R, YAMAHA MT-07, YAMAHA MT-09, YAMAHA YZ250, YAMAHA YZ125, YAMAHA XT225 CELLOW WE, YAMAHA XT225 CELLOW, YAMAHA XJ6S
easy mark
Used for KLX125
Compared to the OEM, the screw mountain part looked smaller, but I was able to install it without any problems.
It's just the right length without the excess length that other people have mentioned.
The rest depends on how rusty it is and how fast it wears out.
At any rate, it is worth using this kind of Parts supply because it is very nice!
View detail
Fits: HONDA Super Hawk III CB400D, HONDA CBX400F, HONDA CBX400F, HONDA GB250 Clubman, HONDA GB250 Clubman, HONDA GB250 Clubman, HONDA CBX400F Integra, HONDA CBX400F Integra, HONDA CBX125, HONDA CBX125, HONDA CBX125, HONDA CBR750, HONDA CBR750, HONDA CBR400F, HONDA CBR400F, HONDA CBR400F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750
Clutch is now lighter.
When I installed it, the grip of the clutch became surprisingly light because I cleaned and applied grease. It looks great with WhiteTank and Contrast in Black. The installation took a little more time than the brake lever. The photo is not Clutch but Brake lever. (NC31) It is View detail
![[STD Lever] Brake Master Cylinder Kit [Horizontal Type 1/2-inches/Tank Separate Body Type]](https://global.webike-cdn.net/photo/impression/12/1251606d8d6125ea8767e937a122d035L.jpg)
Fits: YAMAHA Cygnus X SR, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI SV400, SUZUKI RMX250S, SUZUKI RMX250, SUZUKI RG200, SUZUKI GSX250S Katana, SUZUKI GS400E, SUZUKI GS125E Katana, SUZUKI GS125, SUZUKI DR250S
Satisfied with performance and appearance
[How is it used?
I found brake fluid leaking from the window of my Aprilia RS4 125 and decided to customize it to Tank Separated Type.
It seems to be a common disease of this motorcycle, because there was a person who had the same symptoms on the Net and SNS, and had it repaired at Coking.
Was the one you received as per Image?
It was just like the picture.
The length of the lever was not easy to Image, and I was worried about the type of Short lever, but I chose the standard lever.
Was the installation difficult?
The replacement and installation itself is simple and can be done in an hour including air bleeding.
However, in my case, I put the universal mount on the HandlebarRight Side, so it took me a long time to adjust the fixing place of the Tank.
If you can't use the Stem Mount, and you have such mounts on the HandlebarRight Side, it's safe to say that you should think about the location of the Tank.
How was your experience with it?
I ran it for a bit after the change and Brake's Touch is now Smooth.
With the OEM, it was very quick from the start of braking to full braking, and I felt like I had to pay attention to braking, but now it's gone.
The Lever distance can be easily adjusted with the Adjuster, so you can easily adjust it to the optimal distance.
It was the right choice to replace the OEM Product with this product instead of the Replace.
[Included Parts:were they on?
Bracket, Boltetc.Included Parts:all came with it.
I appreciate that there is a female screw for Fixing Mirror, but of course it is supposed to be tightened together with Mirror, so it would have been nice if there was a separate bolt.
[Additional items that need to be purchased
Of course, M10×P1.25 Banjo bolt is required. I wanted to use Red, so I used Active's Banjo bolt. (https://www.webike.net/sd/1236269/) purchased
Also, it is good to check the terminal of your own Motorcycle, because the terminal for Stop-lamp is out of 187 type male Flat Terminal.
RS4 125 was 110 type Flat Terminal, so I bought a Terminal Set and made a short relay wire to connect it.
Probably, Flat-Type Connector Set of Emon will work. (https://www.webike.net/sd/1353123/)
I thought I might need it in the future, and this 110 type and 187 type are Quantity:MaleQuantity turned into Set:Set and FemaleQuantity:I bought a Set and used it. (https://www.webike.net/sd/24654487/)
[Products compared, etc.].
I compared it with Short lever type and Radipon etc. of the sameManufacturer.
I chose this product because it is easy to use and I am not particular about that for the time being because it is a motorcycle for town and touring.
The lever color is Silver but I chose Black to give it a custom look.
【Review】
I'm happy with the way Brake's Touch and look have changed for the better than I ever imagined.
Repair Parts are also available at Single Body, so it's nice to have peace of mind if something goes wrong.
View detail
![Semi Radial Brake Master Cylinder Kit [Angle Horizontal Φ19]](https://global.webike-cdn.net/photo/impression/1f/1f56b2380b16feca417216bb5376fd01L.jpg)
Fits: HONDA CBR400F, HONDA CBX750F, HONDA CB1100F, HONDA CB1100R, HONDA CB900F, HONDA CBR1000F, HONDA CBR600F, HONDA CBR750, HONDA VF400, HONDA VF750F, KAWASAKI KR-1/S/R, KAWASAKI Z750FXII/III, KAWASAKI ZR-7/S, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZX-7R
Ideal for older motorcycles
I replaced the horizontally mounted Master Cylinder.
I replaced it because I wanted a more Linear feel and it was the right choice.
I'm changing from a 5/8 to a φ19, so even though the Lever ratio has changed, the Brake lever stoke is shorter.
I'm replacing the billet lever with an antlion billet lever, and the adjuster was third from the largest on the horizontal Master Cylinder.
In the semiRadial master cylinder, the fourth largest Adjuster is Quantity:Set
Now, when you hold Lever, LeverControl can be done in the same position as when you hold the horizontally placed Master Cylinder.
Since the viewpoint of the Lever is farther and the Lever is longer than that of the horizontally mounted Master Cylinder, Brake can be used with less force than before.
Breaking of the same strength is possible. (Principle of leverage)
Thanks to this, the Stroke has become smaller, but the power is not needed as much as before, so Contour has become easier.
However, as you can see in the picture, if I cut the Handlebar all the way on the ZX-7R, it makes contact with the Meter.
After that, I use the Fluid Tank that came with it originally.
The antlion billet lever will turn off the brake switch when the brake lever is released quickly, but if it is released slowly, the brake switch will stay on in the On state.
I had no choice but to replace it with a horizontal MASTER Brake switch and the problem went away.
Be careful when replacing the Billet lever with the Other Brand Product billet lever.
View detail
Fits: HONDA XR100, HONDA XR100, HONDA XR50, HONDA XR50, YAMAHA FZ-6S, YAMAHA Lanza., YAMAHA Lanza., YAMAHA TZR50R, YAMAHA TZM50R, YAMAHA TT250R Raid, YAMAHA TT250R Raid, YAMAHA TT250R, YAMAHA TT250R, YAMAHA MT-07, YAMAHA MT-09, YAMAHA YZ250, YAMAHA YZ125, YAMAHA XT225 CELLOW WE, YAMAHA XT225 CELLOW, YAMAHA XJ6S
Used on D Tracker 125 rear caliper
It's just to keep it from rusting and to see if it will move better. The quality is good, so there is no problem. View detail
Fits: YAMAHA XJR1300, YAMAHA XJR1200/R, YAMAHA XJ600, YAMAHA VMAX, YAMAHA VMAX, YAMAHA TT600R, YAMAHA TRX850, YAMAHA TDM900, YAMAHA TDM850, YAMAHA SZR660, YAMAHA TDM850, YAMAHA STRATOLINER DELUXE, YAMAHA SRX600, YAMAHA SRX600, YAMAHA SRX400, YAMAHA GTS1000/A, YAMAHA GRIZZLY660, YAMAHA FZX750, YAMAHA FZ750, YAMAHA FZR750
If you want to replace the plug, this is the one.
I always change the plug at about 3000k, but this Iridium plugs makes less ignition error, and when I change the oil at the same time, the engine sound becomes stable and a little quiet. View detail
Fits: HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA CB-1, HONDA CB-1, HONDA CB-1, HONDA CB-1, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F
good
It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to be honest.
I bought it more for corrosion protection, so I'm happy with it.
View detail
Fits: HONDA 400X, HONDA 400X, HONDA CB250R, HONDA CBR250RR, HONDA CBR400R, HONDA CRF250M, HONDA CRF450L, HONDA CRF450RX, HONDA REBEL(REBEL)500, YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZ250X, YAMAHA YZF-R25, YAMAHA YZF-R3, SUZUKI GSX250R, SUZUKI SV650, SUZUKI SV650, SUZUKI SV650X, SUZUKI DL1000 V-STROM250, SUZUKI DL1000 V-STROM250
Purchased as a spare
I bought this as a spare for my Crimp.
Now you can exchange Chain with confidence.
View detail
Fits: HONDA XR100, HONDA XR100, HONDA XR50, HONDA XR50, YAMAHA FZ-6S, YAMAHA Lanza., YAMAHA Lanza., YAMAHA TZR50R, YAMAHA TZM50R, YAMAHA TT250R Raid, YAMAHA TT250R Raid, YAMAHA TT250R, YAMAHA TT250R, YAMAHA MT-07, YAMAHA MT-09, YAMAHA YZ250, YAMAHA YZ125, YAMAHA XT225 CELLOW WE, YAMAHA XT225 CELLOW, YAMAHA XJ6S
Installation of RVF400 NC35 DAYTONA Stainless Steel Pad Pin Set
I installed it on my RVF400 NC35. size is same for rear side, but front side is 1cm longer. (No problem in use) 。 View detail
![Retro Brake Master Cylinder Kit [Round Integrated Type]](https://img.webike-cdn.net/catalogue/images/105872/74755_TS.jpg)
Fits: HONDA NSF100, SUZUKI VOLTY, YAMAHA RZ125, YAMAHA XT660X, YAMAHA CYGNUS X SR, SUZUKI COBRA, YAMAHA TZR50, YAMAHA TT250R RAID, KAWASAKI GPZ400S, KAWASAKI KH250, SUZUKI RG200, SUZUKI RMX250, SUZUKI RMX250S, SUZUKI SV400, SUZUKI TS125R, SUZUKI TS200R, SUZUKI VX800, SUZUKI Across, SUZUKI GS400E, SUZUKI GSX250S KATANA
If you're looking for a clip-on handlebar, this is it.
Suitable for Handlebar with lowered Grip end.
The Lever touch is also perfect, and the subtle Release operation can be performed without a sense of tension.
I felt it.
Compared to the separate type, the tank capacity is about half, so it may not be suitable for endurance race.
The performance is perfect.
View detail
Fits: HONDA GL500 Wing, HONDA GL400 Wing, HONDA GL500 Wing Custom, HONDA hornet, HONDA Hawk III, HONDA Hawk II, HONDA Zervis., HONDA V-Twin Magna, HONDA VT250F Integra, HONDA VT250F, HONDA VT250F, HONDA VTZ250, HONDA VT250Z, HONDA VTR-F, HONDA videotape recorder, HONDA CBR400F Endurance, HONDA CBR250RRR, HONDA CBR250R, HONDA CBR250FOUR, HONDA CBR250R
No problem
I used it when I changed the oil of VTR250F.
After all, it comes with Packing.
I was able to use it without any extra expense.
I drove about 3000km and no oil leak.
No, I think it's the best cosmetic.
View detail
Fits: KAWASAKI GPZ250R, HONDA CB500F, HONDA PCX150, KAWASAKI Z250FT, YAMAHA MAJESTY250(ALL MODEL), YAMAHA MAJESTY250C(ALL MODEL), YAMAHA FAZER(ALL MODEL), YAMAHA TREET(ALL MODEL), YAMAHA DIVERSION(ALL MODEL), YAMAHA SEROW(ALL MODEL), YAMAHA GRAND MAJESTY(ALL MODEL), YAMAHA Axis(ALL MODEL), YAMAHA Zr(ALL MODEL), YAMAHA YZF750R(ALL MODEL), YAMAHA YZF-R17(ALL MODEL), YAMAHA V-MAX(ALL MODEL), YAMAHA T-MAX(ALL MODEL), YAMAHA FZX250(ALL MODEL), YAMAHA FZr500(ALL MODEL), YAMAHA DT200(ALL MODEL)
My journey to find the optimal Grip has ended with this product.
Compared with OEMetc. Just a little thicker. The thickness is exquisite.
It was a nice relief from the overly agile High Solo and the slightly heavy Throttle.
Also, it works really well with Throttle assist.
With the NORMAL thickness, it will gradually drop and you'll have to adjust it again and again, but with this Grip, once the position is decided, you don't need to adjust anything else.
The thicker it gets, the more gradual the Axel opening becomes, so if you don't like that, be careful.
This NORMAL design, slightly hard grip, and (My) The perfect thickness to fit your hand.
I don't need anything but this Grip anymore, and I hope they keep selling it.
View detail
Fits: KAWASAKI Z400LTD, KAWASAKI Z400 (KZ), KAWASAKI Z400GP, KAWASAKI Z400FX/Z400J, KAWASAKI Z250LTD, KAWASAKI Z1100GP, KAWASAKI Z1100R, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI Z1000R, KAWASAKI Z1000 MkII, KAWASAKI Z1000J, KAWASAKI Z1-R/Z1-RII, KAWASAKI W800, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI W650, KAWASAKI W400, KAWASAKI W1 S/SA, KAWASAKI W3/650RS, KAWASAKI Z900 (KZ900), KAWASAKI Z1000 MkII
I like the fat Grip.
I used it on my GPZ900R.
I'm used to the Inch bar, so I thought I'd get a slightly thicker Grip.
It is thick and easy to grip, and the operation feeling is good.
It's also inexpensive, so it's Wallet-friendly when it comes to wear and tear.
I wish I could have chosen Design.
View detail
Fits: HONDA VTR-F, HONDA VT250F, HONDA VT250Z, HONDA VT250F Integra, HONDA VT250F, HONDA V-TWINMAGNA S, HONDA V-TWINMAGNA, HONDA SUPER HAWKIII, HONDA GL500YAMAHA Super JOGZr Wing Black, HONDA GL500YAMAHA Super JOGZr Wing Black Custom, HONDA GL400YAMAHA Super JOGZr Wing Black, HONDA GL400YAMAHA Super JOGZr Wing Black Custom, HONDA CBX550 F INTEGRA, HONDA CBX400F Integra, HONDA CBR400FFORMULA 750S3, HONDA CBX400F, HONDA CBR400F, HONDA CBR400F Endurance, HONDA CBR250RR, HONDA CBR250FOUR
VTR250
I try to change it every 2 Oil changes, the Filter has more folds than the OEM one so it seems to control the Oil deterioration. View detail
Fits: HONDA GYROUP, HONDA GYRO CANOPY, HONDA GORILLA, HONDA ELSINORE 250(MT250), HONDA APE TypeD, HONDA XR50 MOTARD, HONDA TL125IHATOVO(TL125S), HONDA XR400 Motard, HONDA XR250MOTARD, HONDA XR250, HONDA XR230MOTARD, HONDA XR100MOTARD, HONDA XR230, HONDA XLX250, HONDA XLR250, HONDA XL500, HONDA XLR250, HONDA XL400R, HONDA XL250, HONDA XL125
If you are looking for a slightly thicker Grip, this is the one for you!
The design is very good and I like it. one pointYou can choose the color of your motorcycle.
To install, simply remove the original Grip, put on the Bond, spray with Parts cleaner, and screw in. It is not too hard or too soft, so you can install it smoothly.
The reason I chose this Grip was because my previous Grip sometimes made my hands numb from the vibration, so I decided to replace it to try it out. As for the impression that I tried to use it, there is no Direct feeling in Axel from the thickness. It is a mellow feeling. Because the grip is hard, it is not a strange feeling, but there was a little uncomfortable feeling at first. The vibration to the hand was about the same. If you are looking for a slightly thicker Grip, I recommend it.
View detail
Fits: HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA AX-1, HONDA CB-1, HONDA CB-1, HONDA CB-1, HONDA CB-1, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA CB600F
If you want to buy an OEM, buy this one.
I bought this as a replacement from OEM
very high (Lol) Expensive for nothing. (Lol)
The color of 64Titanium material of the same size is SilverTitanium and about 1000 yen.
Quantity Stainless this time:2pc. I bought a set.
I also bought the 64Titanium and am waiting for it to arrive!
I may return this one depending on the decidedly texture!
View detail
![[STD Lever] Brake Master Cylinder Kit [Horizontal Type 1/2-inches/Tank Separate Body Type]](https://global.webike-cdn.net/photo/impression/0a/0aff6a51d9f8f23a51784ffe1533f27fL.jpg)
Fits: YAMAHA Cygnus X SR, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI SV400, SUZUKI RMX250S, SUZUKI RMX250, SUZUKI RG200, SUZUKI GSX250S Katana, SUZUKI GS400E, SUZUKI GS125E Katana, SUZUKI GS125, SUZUKI DR250S
I'm Sporty!
I wanted to replace the standard with a separate Brake master as the standard is an integrated unit.
BrakeBody is the same form as standard, so it is recommended for those who want to use only MASTER as a separate body without changing the brake performance.
The work is easy if you can replace the Brake fluid.
It is better to ask the shop if you are worried about the work because it is a part related to braking.
View detail