MR-A8S

My friend was worried about thread protection in the consoles of his SUPER CUB CUSTOM, I offered him these spacers. As expected, there are no complaints about the product, the installation went without problems, everyone was satisfied. If you are thinking about protecting the threads in the remote control and placing some additional equipment (windshield, phone fasteners or additional light), this is an excellent solution. View detail

Advantages of Maintenance

I have been using DX since its release. I don't mind maintenance, but sometimes I get tired of doing it when I'm busy with the weather, so it's nice to have less frequent replacements. Fuel consumption and running performance do not change drastically. View detail

Easy installation, no brightness problems.

Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness. View detail

Control voltage is too high.

After installation, I casually applied a tester to the battery and found that 16V was output!
I thought it was quirky and expensive, so I measured it and found that both Regulator and Battery
Idling (1600 rpm) The control was at 16V at 4000 rpm and 17.5V at 4000 rpm.
This is not usable!

Idling when I put it back in the OEM that I removed it from. (1600 rpm) The voltage was 14.5V at 4,000 rpm and 16V at 4,000 rpm.
Wasted... Worst of all... View detail

I wasn't expecting it.

I bought this as a rear shock for my old Scooter.
The Machine is Honda's first LEAD80.
Thank you very much View detail

The size is just right and the texture is good.

Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner. View detail

I got a lot of iron powder.

I used it to clean up my new MONKEY125. It was my first and second DIY oil change, but it was done without any problem. View detail

It's confusing.

When you purchase Slip-on Silencer.
Click here to purchase Gasket." I bought it together with the Full Exhaust System because there was a LINK with it, but it was a part that I would not use unless I was replacing the Full Exhaust System.
I learned from the Instruction Manual for the Exhaust System I received that a joint gasket is required for the Slip-on Silencer for the first time, so this product was a waste of time.
I would like you to put up a LINK to the recommended parts to purchase for the product. View detail

OEM same etc., inexpensive and good.

It was used for the second Exhaust System removal and installation.
The texture was almost the same as OEM.
Since it is Gasket, the feel is comfortable.
Quantity:1 Set of 2pcs. so it is also cosmetically pleasing. View detail

WhiteLight and good looking!

It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light. View detail

Love it!

In a world where it's impossible to find rear luggage racks for Honda Metropolitans this product worked great!! I did need to drill one hole in the body of my scooter but it didn't matter it was worth getting a luggage rack! View detail

Bright and low power consumption

I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling. View detail

Cheap but good product

I purchased it as a replacement for the genuine Benley 110. You can't feel any difference.
Although it is cheap, I think it is a really good product.
I replace it every 10,000 km, but I think the replacement cycle could be longer.
I plan to continue using it.
-------------------------------------------------- -------- I purchased it as a replacement for the genuine Benley 110. You can't feel any difference. Although it is cheap, I think it is a really good product. I replace it every 10,000 km, but I think the replacement cycle could be longer. I plan to continue using it. Powered by Google Translator View detail

OEM same etc.

Quantity:1 Set of 2pcs. to Spare when returning to OEM.
It's good enough View detail

purchasing a spare part

When I changed the Mission oil, I replaced it with a new one and used the spare, so I had to repurchase it.
If the size is right, it doesn't have to be HondaOEM, but similar products are not that cheap, so I bought the same HondaOEM Product. View detail

Grip replacement for LETS4

The LETS4 grips that I have been using for many years have started to hydrolyze and become soggy, so I switched to this product's grips.
The original grips can be easily removed by wiping Parts Cleaner between the handlebar and the grips.
The grip is the same as OEM and easy to use. View detail

No problem, but...

Coupler is a little bit small and a little bit tight.
At first I thought I had the wrong part number because it didn't fit. View detail

I put it on my RG 50Gamma.

It's just like changing a light bulb.
There is no problem View detail

SP TAKEGAWA discharge bolt (w / magnet)

What are you waiting for? What are you waiting for? I want to know what I want to know. I want to know what I want to know.
Although it is not a visible part, this product is really good in that it can filter out iron powder inside the bike. The finish and design are wonderful. Thank you for the quick delivery. I would recommend this product to others. -------------------------------------------------- -------- It's not something you can see, but it's really nice to have this product to filter out the grit from the inside of the bike. The finish and design is great. Thank you for the prompt delivery. I would definitely recommend this product to others. Powered by Google Translator View detail

Replaced with AJ59SUPER CUB110 Iridium plugs

To be honest, I don't know much about the effect of replacing it. 100% of the vehicles I have purchased so far have Windshield IRIDIUM in them.

I only feel that the Engine is working better, but that's OK, it's a world of self-satisfaction. View detail