Reviews
Huge upgrade over stock pegs,Excellent quality and Wide sturdy grip.
Very solid footing with these and they have already withstood a couple of hard falls! Surprising what a difference these make compared to stock! Excellent pegs. Feels like a have a front porch worth of room for my feet to stand on, and they grip to the bottom of my boots like super glue. Easy to install and improved grip noticeably over stock foot pegs.I will say you may have to tweak your stock peg springs to fit around these monsters but still only took 10 min to install both. Great Product, Highly Recommend,webike too fast shipping View detail
Fits: YAMAHA YZ450FX, YAMAHA YZ250FX, YAMAHA YZ250X, YAMAHA YZ250, YAMAHA YZ125X, YAMAHA YZ450F, YAMAHA YZ426F, YAMAHA YZ250F, YAMAHA YZ125, KAWASAKI KX450F, KAWASAKI KX250, KAWASAKI KX250F, YAMAHA WR450F, YAMAHA WR250F
I don't have a Brake lever.
Like Clutch lever, I have been using it for a long time.
The Clutch Side has a different feel to it, though the difference in angle makes the fingers feel fatigued and the grip feel less appealPoint.
The distance between the moving parts may be a slight difference, but the initial operation feels relatively light, and I feel that light brake before cornering can be done smoothly.
As you can see from the comparison image, when the position of the balls at the working point is aligned, the standard position comes to the position where the adjustment screw is tightened about 2 rounds on the OEM side.
Like Clutch, this is also a good point, since installation can be handled by replacing only the Lever.
Cover can also be installed.
View detail
Fits: YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ450F, YAMAHA YZ450FX, YAMAHA WR250F, YAMAHA WR450F, YAMAHA YZ125X, YAMAHA YZ250FX
I don't need to have it, but I feel safe when I have it on.
Although it is not required for motocross course runners, it is the preferred equipment to reduce damage to the Swing Arm when falling down on hard surfaces such as gullies and tree roots.
The OEM guide is completely covered with an aluminum frame, so the impact would be on the Swing Arm joint or the Swing Arm itself, whereas half of the guide is made of material.:The plastic material reduces Large width Damage.
The OEM also provides a quantity for installation methods.:Pair (for Left and Right) The new method of clamping the bolt and nut from the outside is expected to improve the ease of maintenance.
View detail
Rather essential equipment
Equipped with air vent of 13mm height
This is the first time for us to use this product because the product we used to use was not available.
I was concerned about interference with the surrounding area due to the gap between the suspension and handlebar and the ease of hitting the handlebar when it tipped over, but I decided to purchase a short.
As you can see in the photo, the height is about 13.5mm when installed, so almost the entire line fits inside the screw of the fork cap, so there is little risk of damage.
Air venting performance also seems to be fine, as the air seems to be coming out without blowing any oil.
One point of improvement is that it cannot be rotated by Driver, etc., so it is difficult to detach and reattach.
The low Body height also affects it and makes it difficult to pick even by hand, so you may want to be concerned about this point.
(Although it is possible to grip the groove with pliers, it is not recommended because the screw part and other parts are not strong enough.)
View detail
KIJIMAGrip heaterGH08Push Switch
It's been about two weeks since I installed it and so far no problems.
The Grip is a little thicker than I expected, but it is just right for me. I was thinking that I would mishandle the Switch if I used the type attached to the Grip, so I chose this type, and it was the right choice. It is easy to operate and I feel it is convenient to attach it anywhere I want. Also, my palms are quite warm if it is 4 degrees Celsius in the morning and the temperature is at the maximum. But only my fingertips are hard to keep warm. If you want to keep it on all the time, I think the 3rd or 4th of 5 levels would be best. I think the 3rd or 4th out of 5 levels would be best if you want to wear it all the time.
Electrothermal Gloves or Inner Electrothermal Gloves (You will need to bring your own Gloves separately) Would it be good to have a And.
With the skin Gloves with boa, the palms will feel sweaty.
View detail
Fits: HONDA CRF450R, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250FX, YAMAHA YZ450FX, KAWASAKI KX450F
Required for Yamaha-type Fork bottom
[How is it used?
The fork bottom of the YZ series is so thin that it will break if it hits a rock or something,
I thought, "You should have thought of OEM! But I thought so, so I bought this one.
It would be safe to put it on from the time the car is new, and I can't even find a cheap Chinese one,
Was the one you received as per Image?
It is exactly as it looks. It is by far cleaner than making it on a lathe by myself, and it attaches properly.
Anodized is also darker than expected and Exactly on the OEM exterior.
Was the installation difficult?
No hassle at all.
Screw1pc. only.
Wrench was hard to get into if you tried to put it in a good position.
How was your experience with it?
It's a new car but I don't have to worry about it breaking so I can go GunGun bumping into rocks.
It also protects you from unexpected stones hiding under the wadachi.
Instead, Inner Tube is almost a no-guard, so if you get carried away, you will bump it and cry.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
I am replacing the exterior, so a Variation in a different color might be nice.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I would like to have other colors.
I was also wondering about this Type of Guard.
Disc & Bottom Fork Protector Disk & Bottom Fork Protector
Brand:POLISPORT:Poly sports
https://www.webike.net/sd/23639148/
View detail
Fits: SUZUKI DRZ400SM, SUZUKI RMZ450, SUZUKI DRZ400S, SUZUKI RM250, SUZUKI RMZ250, KAWASAKI KLX450R, SUZUKI RM125, KAWASAKI KX250, KAWASAKI KX250F, KAWASAKI KX450F, KAWASAKI KX125, YAMAHA TT250R, YAMAHA TT250R RAID, YAMAHA DT200WR, YAMAHA DT230LANZA, YAMAHA SEROW250, YAMAHA XT250X, YAMAHA WR250X, YAMAHA SEROW225WE, YAMAHA WR450F
Zita Hand Guard Mount Side Type
PROArmor Handguard and Quantity:I installed it on a handlebar with a set, and because it is fixed using the bolt of the triple clamp, the position of the hand guard could not be fixed in the desired place. It is not a problem because of the functionality. The price is very reasonable, so it would be great if the price could be reduced a little more. View detail
SNIPERSNIPEROil Filler Cap
Perfect for One pointAccent. View detail
Fits: YAMAHA YZ125, YAMAHA WR250F, YAMAHA TZR250R, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA SY250F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA XT250X, YAMAHA tricker, YAMAHA SEROW250, YAMAHA SRX400, YAMAHA SRX600, YAMAHA TT250R, YAMAHA YZ125X
Mounted on WR250F
It is still at the breaking-in stage.
Clutch is a Wire type and has been improved from a slippery Fee Ring to a spastic Fee Ring.
Clutch lightness does not seem to have changed.
It is now difficult to enter Neutral, but this area is expected to be a matter of adjustment in the future.
View detail
Fits: YAMAHA WR250F, YAMAHA WR450F, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA YZ450F, YAMAHA YZ450FX
Product Introduction Page may differ slightly from the one on the page. (It is supposed to be improved.)
The product arrived and I used it.
I think it is the same etc. as OEM in terms of feel.
I did not notice any difference in performance.
I think it is a good product because it is reasonably priced.
View detail
It's very conspicuous...
Nomal black caps with pinch points are tacky.... View detail
Improved serviceability
OEMs can replace the 2-parts configuration of the Hexagon Bolt Pin+Minus screw blind with a single 8mm bolt.
The 8mm bolt is also used frequently for maintenance around the brake area, so the assortment of tools can reduce the man-hours required for the work.
In addition, the OEMs were concerned that the outer screw would burn even if Thread compound was used, and the use of a slotted screwdriver would cause the screw to lick every time it was removed, but due to the characteristics of the screw, the possibility of this happening is relatively low. 。
(We still recommend the use of CopperGrease on threads, as seizure itself will occur.)
Replacing one Brake pin will not make you run faster or ride easier, but it will reduce the burden of maintenance.
View detail
Fits: YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA YZ250X, YAMAHA YZ450F, YAMAHA YZ450FX
It is a little weak.
The price, texture, and position are perfect, but I think it is a little fragile for Race.
Lack of skill in tipping over is the most common cause, but tipping over will almost certainly result in bending.
I have the impression that Large is weaker than OEM.
The balance between stiffness and bending may be difficult, but I don't think it is suitable for racing if it distorts so much that its position changes after a single fall.
It is a little unreliable for HED, but not for MX, On-time, or XC.
View detail
reasonable price
I recommend this as a very basic model.
I recommend it for both price and durability. Of course, it also helps in terms of appearance.
It is more helpful in terms of neatness than the rubber plate of the original footrest. I think that such small details are of great help when tuning.
The shoes fit perfectly into the body! Avoid bare feet
-------------------------------------------------- -------- Recommended as a very basic model. Recommended in terms of price or durability. Of course, it helps in appearance. It is more helpful than the rubber plate of the genre of the footsteps. Shoes are just wrapped in the body! Please refrain from bare feet Powered by Google Translator
View detail
Required in winter!
It has been 3 months since I installed the Grip heater on my NC750X and the day to use the Grip heater has arrived. The warmth is not a problem, but the Horn is above the blinker on Honda cars, so the blinker is not easy to operate with winter gloves. Since we did not expect to use Winter Gloves when we installed the Grip, we had to change the position of the Grip in a hurry. Even after changing the position, the connectors on the Grip heater are still in the way (especially when turning right) and the operation is not easy. You may get used to it, but please be careful if you drive a Honda car. View detail
Genuine Yamaha Cotter Valve for FZ1 2006
I was doing a full valve rebuild on this FZ1N 2006 and needed the cotter valves as I did not have these is my garage. I did struggle to find the parts actually available locally so I decided to get them from Webike. I found the parts pretty easily as I already knew the other parts needed and had a schematic for the rest. The price Webike had these for was really good value. With a few other parts in my order, all the items were shipped together with EMS and arrived in perfect condition in 5 days. The packages were all individually packed in Yamaha envelopes and stapled together so I did not lose any in the box. The valves are really small parts and can become damaged if not well protected during transit. Webike have this part spot on, very well packed out with padding. The valves themselves are brilliant quality and you can see this from the machine work that has gone into them. Crisp and clean and no weird shards of swarf on them at all. Just got to get around to fitting this all in with a busy schedule now. Very pleased with the purchase for the 4 cotter valves. View detail
Fits: YAMAHA YZ125, YAMAHA YZ250F, YAMAHA YZ125X, YAMAHA YZ250FX, YAMAHA WR250F, YAMAHA WR250R, YAMAHA WR250X
To Shorten
I bought this to shorten it to make it easier to front up on my Yz125x. The texture is solid and the quality seems to be good. The price is reasonable and I think it is a good cosmetic product. View detail
Vmax1200.
I got this because it was cheaper than OEM. Nothing wrong with it. View detail
Genuine NGK Spark Plug for Yamaha YZ250F 2018
This is a racing spark plug for the YZ250F 2018. We decided we would try a racing plug for a change to see if there was any difference in performance. Finding the correct plug was not super hard as I already have a bookmark for NGK website and that way it's easy. Webike's price for this part was very good value. A lot lower than I could source locally here in the UK. With some other parts in my basket and shipped by EMS all arrived in 5 days.EMS are good value, very fast in delivering and better than some other couriers. All the items in my order were packed individually by Webike warehouse and all nicely padded out in the box so nothing could get damaged in transit and fill any space with bubble wrap and air pockets so nothing can be bounced about in transit. All arrived at my door perfectly. Didn't take too long to fit, pretty straightforward, after all it's a spark plug. Take your time and you will be just fine. Only time will tell if it has better performacne than the stock plug. Very pleased, thank you Webike for all your hard work and dedication. View detail
Genuine Yamaha Gaskets for MT07 2020
I wanted to get a few of these for future projects and it just so happened that one of these was also needed for the rebuild job on the MT07 2020 that had an accident and needed sorting out. This gasket was for the water pump to keep it from leaking. Not really a hard part to find as this one like a lot of other gaskets from Yamaha do fit a host of other models. This is why it is good to get more than one when I order from Webike. The part was easy to find using the tools Webike provide in their help sections and then if you like to cross reference, do this via Yamaha schematics. Simple. With a lot of other nuts, bolts, washers and gaskets needed to complete this rebuild, I had a lot of the parts shipped together to save me on shipping cost. When you add a few other parts, it really does work out cheaper in the long run. Also, EMS saves me time by shipping in a efficient manner and gettting my order to me fast. In 5 days from shipping, my order arrived. All my parts were in great shape, no damage caused in transit at all. I am not surprised really as Webike warehouse do a cracking job at packing the orders well. I got 5 of these washers and each came in a Yamaha packet. The gaskets are I think, copper but may be a composite but defintiely have copper in them. These are perfect as copper is a soft metal and will crush down to hold a tight seal. Exactly what you want for a water pump. Very pleased with the purchase and the gaskets are super nicely machined. Great work Webike, thank you. View detail