Very convenient.

This Connector is used to get power from the Mini Flat Type Fuse.
This is very useful.
I often use it as a power source for my car. Most of the common vehicles have a fuse box at the foot of the vehicle.
I need to pull power to run the DriveRecorder, Radar detector, etc., but the Cigar lighter socket makes it look rather ugly...
In the case of a motorcycle, there is no Cigar lighter socket in the first place.

The Fuse is taken out from 15AFuse, but since it is via Pipe Type Fuse 5A, it will fuse if a load of 60W or more is applied. (The Fuse that is connected to the MainFuse is 15A, so the allowable power of the MainFuse is 180W. Paradoxically, if you use more than 120W on the MainFuse side, the Main will cut off if you use more than 60W)

A fuse box with a lid requires some ingenuity in terms of how the wiring escapes. View detail

I didn't think it would be this easy.

DAYTONA
Attachment Power Supply Unit D-UNITPlus (DeeUnitPlus)
https://www.webike.net/sd/24232600/
Used to take ACC power from the
I was worried about whether the lid of the FuseBox would close properly, but it did, to the point that it never closed completely but not problematically.
Need to check continuity and be careful about the direction of insertion.
I installed a pluggable Fuse to get power before the current flows through it. View detail

Easiest power extraction

There are three simple ways to extract power from the Gixxer 2020 MODEL~.

Bullet terminal terminal for attachment hidden under the tankLeft Side, not accessible without removing the Side cover

Computer diagnostic coupler in the ETC storage space under the Rear Sets.

And from the Spare sub of the Fuse BOX under the Front seat.

This is the quickest way to get it from here, so this guy is always there for us.

I usually use Bullet terminal, but this time I used Terminal, which is quite easy to use. View detail

That might be a little high

I bought it to get power from a Fuse box.
I can easily get power by simply replacing the Fuse.
As a product, it is easy and good.
However, considering Product Contents, we feel the price is high. View detail

I needed it to install the D-UNIT.

[How is it used?
DAYTONA's Power Supply Extraction Parts "D-UNIT. I bought this product because I need to use it with D-UNIT and Fuse box. I checked it by myself, but it was not written in the Site of D-UNIT.
(I'm a beginner, so I'm honestly not sure if it was really necessary...)

Was the one you received as per Image?
It was just as Image.

Was the installation difficult?
I was able to install it without any modification.

How was your experience with it?
It's nice to know that no processing is required.

[Included Parts:were they on?
This product only.

[Was there anything that disappointed you?
None

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer

Please check the number of voltage you need before you buy. ←People who bought various products without checking well View detail

Note the shape of the Fuse BOX

The USB power supply was prepared to be installed under the Rear Sets. Installation was easy and only needed to replace the Fuse, but the wiring from the Fuse did not tighten against the lid of the Fuse box, an elementary mistake due to lack of confirmation.
I stopped taking it out because I was worried about it. It's a good product that's easy to use, so I'll think about converting it to something else. View detail

Quick and easy power removalParts

To take out the power supply of DriveRecorder
When you don't need it anymore, you can just pull it out and put it back in.
It's equipped with Fuse, so you don't have to worry if it goes wrong. View detail

Get the power!

I used it to get the ACC power supply for my drrorecorder.
It's so convenient to take Plus just by replacing Fuse with Ideas product!
I'm sure a lot of DIYers love it. View detail

Note the difference in standards

Bought this to get a power supply for my etc installation.
It is possible to use it especially without a problem. However, it is a difficulty that Fuse BOX does not close because the line comes out from the upper part of Fuse. View detail

watchman

[How is it used?
I used this service when I installed ETC in my Motorcycle.
BatteryI thought about getting a power supply directly from the battery, but after thinking it over, I realized it was not an option.
Finally, I used this Fuse to interrupt the power supply of other Parts.

How was your experience with it?
This is Emon's FuseSeries, which is widely used around the world.
This time I used it to get power supply to ETC. I was able to insert it into the existing Fuse box without feeling uncomfortable.
Also, I was able to actually run it through the power supply without any problems. It's just like its reputation.
There are a lot of supplies that use electricity these days and if I have the opportunity to use them again in the future, I will choose this one.

How did it compare to other products?
The others are not particularly comparable this time.
I've always thought of Fuse as this.

[Points to note]
After all, it's a Fuse, so once it's done its job, it's done its job. Please be careful about installation. View detail

I've got power.

I bought this to power my Ignition Illumination. It is very easy and reliable to power.
I used it for Light relationship. View detail

To get the power out

Purchased to remove the USB power supply
All you have to do is replace the Fuse, so it's easy to revert to the original

However, depending on the shape of the shoe box, the lids may be too tight to close, and the cord may be overloaded Please note that this will take some time View detail

It's convenient

I used it for the first time to power the Grip heater
I don't want to do a bacchanal I could have branched out from Harness on the vehicle, but if I take it from Fuse, I can take Harness from It can be powered off without damage
I wanted to get it from the ACC power supply, so Horn (10A) Fuse of
Make sure it's energized with IgnitionOn and the work is done It's easy
It also comes with a 5A GlassTube Fuse for peace of mind
According to Emon, this power extraction Fuse is different from the standard Fuse that is pulled out They have an orientation (It wasn't mentioned in the Product Package.)
The correct way to do this is to attach the cord or the side with the cord attached to the side with the power coming from the vehicle
I don't know why I'm an electric onchi
It is very convenient, but if you can get the code that comes out of the Fuse to come out horizontally if you can I wish I could have installed it without interfering with the Fuse lid
For those who don't want to chop up OEM Harness, it's Recommendation
View detail

Mini Flat Type Fuse Power

Basically it's easy to install because it just plugs in.
In case of HORNET's Fuse box, you can install but the lid did not stop.
It forced me to close but it made me feel uneasy.

I was able to easily replace the glass tube of Fuse by just opening it. View detail

It is convenient Items

Used to extract ACC power from Fuse box when installing USB power supply. There was such a useful thing and it was saved.. It is simple because it only connects by connecting the Bullet Terminal terminal to the connecting side. View detail

Even beginners in electrical equipment can do it easily!

In order to install the USB power supply, I purchased the USB power supply and Mini Flat Type Fuse Power with the Bullet Terminal terminal and secured the power from the Fuse box. It is the best product that can be easily taken for those who are beginners of electrical equipment. View detail

Usb Power supply installation

I bought it to install usb power supply this time.
It's very easy to install, just replace it with Fuse from Motorcycle.
I think that it is easy to use and a good product though it was myself that I had never touched electrical components etc.. View detail

If you take power from Fuse

【What made you decide the purchase?】
I did not want to mess with the Wiring of the vehicle, I wanted to process the installation type, so I bought it.

【How was it actually used?】
I could use it without any problem.

【Was it difficult to install? (Hard parts case)】
If FuseBOX is known, anyone can do it.

【Please tell me the point of installation and hang (in the case of Hard parts)】
If you do not process FuseBOX, it may not be

[Is there anything I was disappointed about?]
There is none.

【Hope for Manufacturer - Please let me know if you have any improvement points]
There is none.

【Have you compared items?】
There is none.

[Others]
When it is not necessary, it causes Trouble, so I removed it. View detail

You should carry a spare Tube Fuse.

I bought it to secure the power of Cigar socket.
Socket itself also included a Fuse power supply, but I could only divert from 15 AFuse, I did not want it, I bought this.

Also, let's carry a spare Tube Fuse.
It may become troubled at your destination. View detail

Easy chin

Used in Car instead of Motorcycle.
I wanted to take power from a solid place when installing ETC. If it is a Fuse box, it should not be wrong, so buy this product.
Super easy to just remove the Fuse.
There is no problem if you only notice the orientation. Electroscopic Testeretc. Let's check with. View detail