Reviews
Fits: KAWASAKI GPZ900R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPZ750R
I think it's a good thing as a thing
I looked at the Instruction Manual when I received the product It was slippery It was able to install because it can only be attached as it is attached Coupler is OEM, TAB and receptacle were opposite Because there is no claw, it cannot be locked It was a little bit difficult Furthermore, I had a little trouble because Wiring on the Coupler side was on the opposite side
I don't know if it's a reverse car or a FOR JAPAN MODEL car or a different year, but I'm going to get an A7 reverse car Installed 。
I was able to install it in an hour because I can do everything except the engine, to some extent
I'd like to see a better description of the product and improvements to Wiring, etc. if it's different by model year, etc Please
View detail
Fits: KAWASAKI GPZ900R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPZ750R
As well as midsummer ...
I got an Oil Temperature Meter and knew the temperature of the Engine by a number, I knew, but since the oil temperature is quite high except for driving, I thought that it would be better to lower even a little.
Since installation is Harnesson, I think that it can be understood with the paper of the manual, because it is WhiteBlack, there is a person who carries a procedure in a color easily by net search if you do not know.
You can install it only if Tank, Seat and Seat side cowl are removed..
Although others were also listed, Harness in Cowl gets hands if you just remove Inner! But it's quite narrow, so be careful not to make scratches on your arms etc..
Switch, but when it is attached to HandRight Side, it is still not long enough. I extended it, but if I can not do it, please install the Switch box near the Center or recommend a place other than Hand.
Wiring extension work also Quantity : Because it is only 2 pc, it can be done easily, but ...
Although it is performance, it is not necessarily a sharp drop in midsummer traffic jam, signal wait, wait for a signal, please think that it is enough to keep the temperature going up. Even when the fan revolves, since the hot air will stay on the engine side, I think that it will cool down more efficiently, considering the way to pull out the wind well.
View detail
Fits: KAWASAKI GPZ900R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPZ750R
Defective item
Although it corresponded, it does not operate after trying it at the beginning. Connector mismatch.
Things that Wiring was wrong when sent back.
I replaced it and sent it back, but I do not feel like finishing summer already anymore. The Connector must be fitted or fixed with Tie Wrap but it can not be thought of as Exclusive Design by vehicle type.
View detail
Fits: KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1100
I am satisfied with the performance.
I think that the other person was also filled in, but I think that Wiring is a bit short. Switch can be installed if it is turned upside down, but it is regrettable that the Button characters are reversed. View detail
Fits: KAWASAKI GPZ900R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPZ750R
Switch is crappy.
I felt that the start of OEM fans started being slow, so I bought this so that I could turn it arbitrarily.
Remove Left Side Cover, Tank and let each Relay interrupt this product.
Because it interrupts this product, there are two Couplers for each Relay, but one of them has no claws and it just pulled out, it got pulled out. So I wonder if it is necessary to process it so that it will not come off at Tape.
One of the two Relays is inside Cowl next to Headlight. In the Instruction Manual "Remove Cowl ~" Although there is a statement of, you can reach the Relay even if you do not remove it.
And although Title collection, Switch is crappy. (It was made by KOKO)
View detail
Fits: KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1100
It is not attached, unless the place into which a 6-mm Bolt is put has 4-mm solderless contact and it exchanges for it. If attached a little more simply, I will think that it is good. Although it is it and a Switch, since wiring goes a
It is not attached, unless the place into which a 6-mm Bolt is put has 4-mm solderless contact and it exchanges for it.
If attached a little more simply, I will think that it is good.
Although it is it and a Switch, since wiring goes away upward, water does not pour in or it is uneasy!
I think that it will become good goods if this neighborhood is improved.
View detail