Normal Handlebar

Very decent Handlebar at an affordable price
There is quite a wide variety, so you will be able to find something that suits you. View detail

Used for XLR80 Handlebar

[How is it used?
I purchased this product because the OEMHandlebar was bent
The height of the Handlebar is just right and it seems sturdier than the OEM.

Was the one you received as per Image?
It was just like the image.

Was the installation difficult?
The Switch floats a little because there are no holes for mounting the Switch, which was the case in the OEM version.
Other than that, there are no problems. If you are concerned about it, drilling holes will help it arrive nicely.

How was your experience with it?
The height of the Handlebar has been obtained, and it is now at a good height for both Sitting and Standing.

[Included Parts:were they on?
Sticker was included.
[Was there anything that disappointed you?
Not particularly. View detail

Can be mounted on WR155

[How is it used?
Available for WR155 Handlebar.
OEM is low, so anything taller than this item may be tough.
Also, this Handlebar is too low, making it difficult to close the Bolt on the Clamp.

Was the one you received as per Image?
It was just like the image.

Was the installation difficult?
Drilling is required to replace the handlebar.

How was your experience with it?
It is a good aperture.

[Included Parts:were they on?
It came with a set of bar pad.
Bar end caps were included.

[Was there anything that disappointed you?
Not particularly

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer View detail

It's still cool.

[How is it used?
I bought a CRF125F and replaced the OEM handlebar with an Aluminum handlebar. The hand guard that I always use is only for Aluminum Handlebar.
I really wanted the 110 mini from Renthal, but the delivery date was undecided, so I had no choice but to go with this one.

Was the one you received as per Image?
The image is exactly as shown in the image. The quality is perfect.

Was the installation difficult?
Just replace it with OEM.
You can take a picture with your phone before you remove it so you can see where the Wiring and Wires went through.

How was your experience with it?
I knew from the measurement that I still lacked a little bit of start-up, but it wasn't so much that I couldn't ride, so I was satisfied.
I'm also thinking of chewing on UpClamp.

[Included Parts:were they on?
Bar pad is attached.
I am thankful that the CRF125F does not come with OEM.

[Was there anything that disappointed you?
Not particularly

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Grip will need to be new and should be bought at the same time.
This time I decided to go with SCOTT's Mellow Grip. (https://www.webike.net/sd/24982240/)
Also, Grip bond, which is often forgotten. (https://www.webike.net/sd/20034236/) View detail

Just low enough

Used for Z125PRO

HURRICANE Condor is not yet in stock, so I changed it to this one for the time being.

Position is good, although some holes need to be drilled to stop the rotation.

With Striker's Rear Sets, the look is neither too aggressive nor too rough. View detail

Suitable for MOTARD

In use with dTRACKER.
The height aperture width is excellent. View detail

I like that it has Memory in it.

I used this for the Handlebar on my KLX230R.

I didn't have any problem with the NORMAL Handlebar, but it was a little too wide and I felt a little uncomfortable when standing, so I replaced it.

This Handlebar also had a length of 800?:Pair (for Left and Right) I cut about 1? at a time, but as expected of Pro taper, Memory was included for Cut so that I could adjust the width of Handlebar from the beginning.:Pair (for Left and Right) I'm glad that I was able to get it together and Cut it easily with

Also, the Clamp section contains Memory that is easy to adjust, so I think it's a good Part that conveys the idea that Handlebar is a Part that adjusts Position.

It has a more subtle bend than the NORMAL, and is easier to ride when standing. View detail

It's easy to center.

Because the Handlebar of the Motorcycle that I purchased had a Handlebar that seemed to be available.
I purchased the reliable Pro taper Handlebar.
Each size is listed in detail on the site, so I was able to measure the size of the actual motorcycle and purchase it. View detail

It's not the color I wanted, but it's pretty

I bought it to use for Honda msx125. I wanted to purchase the black box, but the black box was out of stock for several months. use on honda msx125 I wanted to buy a black box The black statue is out of stock for several months, so wait and wait I don't want to wait anymore Just purchased in different colors Although it is still before installation Since the net information is much lower, I think the position will be more comfortable. translated by Google Translator View detail

It was too low for Grom

I bought it for Grom
I bought the Suzuki mini to see if it was lower than the Honda mini
This is before installation, but it may have been too low for the quicksilver
Could the Switch box interfere with the 20mm Handlebar spacer, it's almost an OEM It will be the same height and width as

The Honda mini is the Large person's recommendation for the Grom
The texture is unquestionable View detail

NAKED Wind Motard handle

XR650RMOTARDSpec. We mounted on.
【Purchase motive】
- Handlebar with height when KICK thinks that Balance is good for you.
- Upgrading effect as seen with Handlebar which can be mounted with Top Buriji of NORMAL.
[Getting Started]
Just by removing NORMAL and replacing it, LeftSwitch's anti-rotation drilling is DIY
【Status of use】
- Naked motorcycle Aiming for the visual effect of the wind Bar pad is removed.
- Balance at the time of KICK got better.
- The width of NORMAL 800 mm to 730 mm thinks that it is Handlebar change of Naked motorcycle position from Off car.
- Mirror is CRF 1000 LOEM and it has good feeling behind with no discomfort
- Installation of AELLA Bar EndProtector for MONSTER S2 (Hole diameter 13 mm)
- The visual effect of Handlebar seen by Pad got better.
[Unfortunately]
- Yamaha Mini's Paint is not necessarily honest in the bar center (Because it is HONDA XR). I think Seal is good.. View detail

I like it

I like PROTAPER because I used it before.. I made it to HenryLEAD which I bought also for WR 250X earlier although I was quite lost as to which shape is suitable for SEROW. The touching feeling was that it became easier to stave and the feeling that the end part was going down was lost, and the vibration was reduced more than anything, the hand became hard to become numb. (The human body is going to adapt to things as it is) I do not feel awkward already. Since the Bar pad gets in the way of installation, I removed one Bolt. View detail

I think it's good.

I attached HenryLEAD to SEROW 250. Hand guard is RALLY 50 of ACERBIS. Everything went without problems. Just when Blinker's Switch box tightens Screw it works. I will try something to deal with it. It may be a bit painful to open a hole in the Axel fixing dock with Drill. Clap's Bolt is hard to close due to Pad. Vibration has been reduced and traveling becomes very easy to get on.. And it's Parenthesis. View detail

I like it ♪

Because there are many kinds, so I decided to raise or lower Handlebar, how to pull it, I became a good kick Lack to think of my own position ♪
I thought of other Handlebar, but I made it with the price and Handlebar shape ♪ View detail

Thank you!!

I was saved because I came soon! I would like to use it again.. Thank you !! Thank you !!!!!!!!!!!!!! View detail

Your service are Top 1 shipment are very fast, so to the customer service immediately respond to me .. will order more parts from you soon. Thank & Regards Bryan Robson Jospeh

Your service are Top 1 shipment are very fast, so to the customer service immediately respond to me .. will order more parts from you soon. Thank & Regards Bryan Robson Jospeh View detail

I want lowdown handle and such such such such such...finally i found protaper. it is very wonderful product and quality is very good

I want lowdown handle and such such such such such...finally i found protaper. it is very wonderful product and quality is very good View detail

Attached to KX65

PROTaper's MiniSeries is Just size on KX 65 !!
Renthal's 784 etc. Since the Center part is made narrower than the Guard, there are quite a lot of degrees of freedom of the operation system when attaching Guards
Large falling fall (JumpShort) I tried it twice, but there is no evidence of bending (Humans have broken bones) So I think that there is durability as it is View detail

Cost performance OK

I am using it for DT 200 WR. I chose this Handlebar size check that Normal handle would be similar in shape because it got bent. You can use it as it is without discomfort without cutting the width. It looks much better than NORMAL.
We examined other Manufacturers, but the price was cheap but there was also NameValue of Pro taper, which I thought it was a good product of Cost performance. View detail

KLX125

OEMHandlebar when standing with KLX 125 was low, so about 1 than OEM. I selected this Handlebar to up about 5 cm. Regarding the installation, since the Clutch holder of KLX 125 is not a split type, use Handlebar to slip the portion of non-slip? With File etc etc etc. I did it.
Clutch Cable that I was worried about and I was able to attach it without changing too much in OEM. View detail