Heat and scratch protection

The evaluation did not seem to be bad, so I bought it to try it out.
Since it seems to have high heat resistance, it is used to prevent heat deformation and scratches on the inside of cowls. The price is not that much, and there are a few meters, so it can be used to some extent. I would like to check the adhesiveness for a while. View detail

Thermal measures!

I installed an Oil Temperature Meter on my NC750X, but I have to pass the WiringCable under the Engine, so I will try this heat resistant tape as a thermal countermeasure. I think it will be no problem. I am also planning to put the heat resistant tape on the Under Cowl of the NC750X because the heat from the exhaust system melts the Under Cowl. View detail

For Tank and Radiator hose

I put it on EXC-F Tank and Radiator hose.
Tank was too thick to apply with other heat shielding Seat, so we applied this one.
Even though it is not as thick as a proper heat shield Seat, so the effect is not half as good, it is still much better than nothing.
I have had a tank deform due to heat and leak gasoline, so I am hoping this will be a solution to that problem.
The radiator hose is close to the exhaust pipe and is not particularly heat-resistant, so coolant blows out quickly, and the heat can cause holes in the hose.
It is very easy to use because it can also be attached to the back of Cowl. View detail

Adhesive enough

It can be cut to any size, so it can be stretched to fit any location.
The adhesive is firm, so it did not peel off after application.
The heat resistance effect is sufficient and effective in preventing deformation and discoloration of the Under Cowl due to heat from the exhaust pipe. View detail

It's good to have some comfort.

[How is it used?
It was just installed the other day. Practical durability performance will be verified in the future.

Was the one you received as per Image?
It is close to Image, but the thickness is thinner than I imagined w

How was your experience with it?
After I changed to Earls Gear's Full Exhaust System, I was worried about heat distortion of Lower cowl because Exhaust pipe, RightLower cowl and Clearance became narrower. I found this insulation tape on Webike, so I tried it. I found this insulated tape on Webike and gave it a try.
Easy to apply and perfect adhesive strength. Because it is not thick, the tracking of the curved surface seems to be good.
But what about the important insulation performance? This is my feeling.

[Points to note]
Since it cannot be reapplied, the surface to be applied must be thoroughly cleaned and degreased.

How did it compare to other products?
I haven't compared them because Webike didn't give me any other choice. However, the OEM insulating seat material on the lower cowl of Kawasaki ZX-14R is quite thick, so the insulating effect may be a little less than that.

Other items that would be helpful
It is better to prepare the cleaning tools such as Silicon-off and Parts cleaner.
It would have been nice to be able to choose the thickness of the Heat Insulating Material as a product Variation. View detail

It's going to stick.

This product can be cut to any size and can be attached to any place of your choice with firm adhesive force, and is heat resistant to prevent deformation and discoloration of the Under Cowl due to the heat of the exhaust pipe. View detail

Mostly satisfied!

[How is it used?
I used it for Under Cowl of YZF-R25 which I use as Racer.

Was the one you received as per Image?
It was just like the Image. The thickness is there and it looks promising.

How was your experience with it?
The adhesive strength is strong there, but if you want to put it on the inside of Under Cowl, be careful because it will come off if you don't degrease it well.
In addition, it is not a problem if the shell of the Silencer hits, but if the exhaust pipe hits directly, it will be burnt. (laughs)


How did it compare to other products?
It's simple and easy, but the ones from Magical and others are thicker and more durable with things like Glass Wool mixed in. View detail

GORILLA・Full CowlSpec.

Created a GORILLA Full Cowl vehicle and used it for Cowl and paint protection.
Since the Exhaust pipe on the Over is going through the Limit.
It's not painted yet. View detail

GORILLA、Full Cowl

I am currently building a GORILLA Full Cowl car and bought this to protect the Cowl and paint from the heat of the Exhaust pipe.
It's not finished yet, but the size is good for Small Type car. View detail

I think it's good

I put a large piece of Heat Insulating Material on it and stuck this product around it.
I took this approach because it's relatively easy to cut.
I didn't use it for Motorcycle, but I repaired the Plate part of the GasCooker that had a hole in it from the heat.
It's been about a month now and there is no damage to the tape itself.
It was surprisingly useful, so it's a big deal. (Lol)
But for a few days, I think it was the glue, but the smell was too strong. View detail

Tank It is the width of the product that is easy to stick to the back

I bought it by measures against heat shielding to Fuel Tank going up from Engine.

This product has never looked at the shop which sells it in store inventory.

Since the use destination was Fuel Tank, the pasting surface was full of curved surfaces, so it is very easy to paste this product which has been cut to 5 cm width beforehand.

Because the adhesive tape is also solid, I think that once you paste it will not peel so easily.

Because of that, the Tape gets in the way when cutting the product with Scissors, and the adhesive Tape kasu adheres pretty much to the blade of the Scissors, so let's wipe frequently.

If not doing so, the adhesive Tape kuss calls further kasu, which results in a way to tear off the thermal barrier fiber and call for fraying of the fiber unnecessarily.

Anyway, the 5 centimeter width standard was easy to stick, workability was also very good View detail

good

I tried to prevent deterioration of the 2 st Oil tank of the CRM 250 rr due to heat. Because the shape of Tank is not square, it was hard to stretch, but it stuck well. When I touch Tank after running, I feel that the heat has not been transmitted more than before. I will stick to other parts and check the effect. View detail

Used for insulation of Fuel Tank

Temperature also rises to protect Gasoline from the heat of Engine
Heat insulated using this product on the back of Fuel Tank.
It is wrapped in a roll and easy to cut to your favorite Size
There is no problem with adhesive strength.
In bad products it may be scratchy with Glass fiber,
This product is excellent in workability without Glass fiber Rose. View detail

Thermal insulation tape

When installing the outside RightAir Scoop outside the buell, the intake manifold comes very close to the position, so I bought this product for the prevention of Scoop's dissolution.
Easy to handle, easy to cut with scissors in any shape, you can stick to small places.
It was affixed to Scoop a little Large, I confirmed the engine start condition, but there was no change in shape, securely insulated Scoop and insulated.
I think that it is exactly good for the protection of Under Cowl by the heat from the intake manifold such as SS. View detail

Thermal insulation tape

Due to the heat from the Engine's Rear bank, the Rear seat got very hot, lacking comfort and buying it for countermeasures.
Just stick it to the Reverse side of Seat, it can be installed very easily, it can be easily cut with scissors so it is easy to match any shape.
When I pasted it, the heat can be reduced considerably and I am very satisfied.. View detail

At such times, Posh is reliable.

I was looking for Heat Insulating Material when exterior of Exhaust System side of DR-Z 400SM was exchanged.
Of course OEM is also good, but consider buying here that it takes time to delivery.

Packaging is frugal, quality is top notch.
You do not have to over-pack it.

What about this Tape?

- Cut to your preferred length
- Since adhesion is not too strong, it is rare to fail
- Moderate Length
- Being able to use it other than exterior

Is this?.
It is nice to be cheap, but if quality is not good it will not be used.
I do not want it when the exterior melts..
On that point, if usability at this price is good, it is 1 pc. I regret that I should buy it (Lol) View detail

Scooter's Helmet inSpace's thermal barrier

I used it for heat shield of Helmet inSpace of Addressv125.
Remove Helmet in, paste from the outside.
The product came in one winding state.
I cut it to an appropriate length and pasted it.

I thought that Aluminum Tape says that it would be hard to stick to a place where it was bent..
When I started pasting, I felt that workability was very good because it was stuck to the curved surface unexpectedly and flexibly.

I thought that it could be used in various places depending on how it was used.

The price was affordable, so I thought that COSPA is a good product. View detail

It purchased to use it for the interference portions of the Silencer of a Muffler, and a Undercowl.Since the product of other company seemed to be large and seemed to be user-unfriendly, I think that this article of a moderate size is good for an indi

It purchased to use it for the interference portions of the Silencer of a Muffler, and a Undercowl.Since the product of
other company seemed to be large and seemed to be user-unfriendly, I think that this article of a moderate size is good for an individual user.While using it about
engine performance, he would like to discern, but since there are not necessarily so various kinds, even if somewhat powerless, I think that the width of selection is narrow. View detail

It was used for the sheet flesh side for the measure against heat. Since there is a certain amount of thin elasticity, it is easy to stick also on a curved portion.The heat of hips decreased certainly.Although I think that fuel-tank flesh sid

It was used for the sheet flesh side for the measure against heat.
Since there is a certain amount of thin elasticity, it is easy to stick also on a curved portion.The heat of
hips decreased certainly.Although I think that
fuel-tank flesh side has an easy-to-use Seat type, it is the best for the measure against heat of a fine portion. View detail

It purchases again as a measure against heat of a Regulator. This is a gadget from which attachment places, such as a part which were dramatically convenient, and curved or curved, are not chosen.This use part was used for the measure against heat of

It purchases again as a measure against heat of a Regulator.
This is a gadget from which attachment places, such as a part which were dramatically convenient, and curved or curved, are not chosen.This use part was used for the measure against heat of the Regulator attached just in front of the Engine.There were only only 3 cm of crevices between an Engine and a Regulator, since there was an example which a Regulator gets burned and damages with engine heat well, the thin griddle of the Aluminum was purchased in advance, the heat-resistant Tape was stuck on this, and preventive measures were carried out.It is used, there is almost no propagation of heat measure before, and it obtained the result which is protecting the Regulator from the engine heat under the blazing heat of midsummer.He is very Satoru Taisho.We recommend you to cope with the direction of Buell riding on this heat-resistant Tape by all means. View detail