To hide the hexagonal hole

Plating was peeling and falling apart, so the
Purchased to replace
It looks pretty shiny. View detail

2 while shopping

It's just self-satisfaction. I don't care if I don't have it.
It is a Dress-up that only those who ride the same Motorcycle will notice.
But isn't it good! View detail

I think it's good

It is just a decoration, if you like.
There is no sense of discomfort as if it had been attached from the beginning.
It is completely self-satisfying because no one but the person himself notices it. View detail

PetitCustom

PetitCustom Bolt Hole Cover for Handlebar Clamp. View detail

It's cheap and it looks good.

I used it to improve the appearance of the cap bolt around the handlebar.

As you can see in the picture, the color matches the Titaniumium color of Posh's NASA TypeCap cover.
It's useful because you can almost hide the Bolt with both of them.

Just one note on installation.
Material:There is a cut-off from the RUNNER 125 at Plastic, so make sure it is on the lower side, where it is less noticeable. View detail

To prevent rust.

MirrorMounting Bolt tightening holes
There was a pool of water and Rust.
I bought a Cap!
There was one with and without a rubber at the end of the cap, but
The part to be used this time is the Bolt that attaches to the horizontal direction
So, is it Large sturdy without Rubber? I think so.

Does the size fit since it's a special bolt?
I was worried, but the Exactly/Fit
This way, there's no water pooling in the car wash or rain.
It won't rust and is safe.

Quantity needed:2pc. Against the Set
Quantity:1 Set of 4pcs.:2pc. The Set becomes a spare part.
It was a waste of time to find a usable part of the
I couldn't find anything.

Quantity:1 Set of 2pcs. products would also be available.
Thank you.
View detail

Black chrome？

It is Black chrome, but it is not so black as almost Chrome image.
If you ask me. Is it a little Black? That's about it

Cap bolt's inner hexagon with Exactly Uniqlo plating is transformed into a high-grade bolt
Don't make a mistake as it's not something you can put in the Screw hole! I made a mistake, W.

Is it a bit high? Maybe you could get 10 for 1,000 yen? View detail

I wouldn't be surprised if you dropped it at any time.

This is another PetitDress- found at KITACO and ConvenienceParts upItems. upItems. it's totally dress-up, because for practical purposes I don't need this kind of Cap. However, I thought it was well made for that purpose. Anyway, the body is Material:It's aluminum and has been properly treated with anodized aluminum, so the color and The shine is good. Normally, the Bolt cover is made of soft plastic, but it is not made of aluminum. Since it is not deformed, the O-ring is inserted into the hexagonal hole of the Cap bolt with it. This is a good example. The part where the O-ring is properly fixed has a groove digging, and it takes a lot of time and effort to process it. I'm there, so I guess it's no wonder it's so expensive.
However, this O-ring is a tricky one. The one for the smallest M6 Screw has a very small O-ring. So it was Large strange for me to fit it in with my old eyes. And it's probably because of the airtightness of the O-ring. Sometimes it would fall off on its own after a few seconds of fitting. No matter how many times I pushed it in, it would fall in such a way that it would come off of itself. As I observed, it seems that the air between this Cover and the Bolt's hexagon hole is compressed and the force The O-ring seems to be pushed back in. That's how airtight the O-ring is. As I was TRYING, there was apparently a point where the air inside was released and the push back phenomenon was The Large threshold type makes it difficult to push in. I hit it with a plastic hammer and pushed it in (I may not be able to get it off later).
However, I felt that the risk of falling due to vibration while driving was Large. It is not at present, but I must be prepared to lose it. At that time, I have no choice but to buy the replacement parts and deal with it.
I used 4 bags this time, and the cost was about 3,500 yen. Well, it's a good cost-benefit ratio for a dress-up, isn't it, using Pinpoint I think you can be satisfied with it even if you don't have a lot of them. However, because I think that it is not strange when it disappears, I think that other custom parts purchase You might want to buy a spare while you're at it. View detail

Luxury in a cheap Bolt

If you put this on, even a cheap Bolt will look luxurious If you care about the appearance, this is the recommendation for you

I was motivated by the crappy Bolt that came with the Over's exhaust system This was introduced View detail

In places you do not want to make it stand out...

A fashionable Bolt cover of DAYTONA and POSH is also good, but I like this kind of simple design in places where you do not want to make Cap bolt stand out.
I purchased the same Cap Bolt Cover last time, but I bought it as Stock.
Which Manufacturer should cost half price, or about 30%.... View detail

Quality has Rose

I attached it because the head of Bolt of Uniqlo plating color is noticeable when Pannier caseMount is attached.

Some things do not fit unless they have to be pushed strongly with your fingers "Scauper" And there was something felt lightly, I felt quality with Rose. It is an impression that it seems that it is just getting off by vibration.
400 yen is too expensive for the four pieces of Plastic like this! View detail

Preliminary purchase.

Stock got lost, so I bought it. I think that it is more durable than the thing of the plaque, so this Bolt cover is all Material : I am wearing Aluminum stuff. When installing, RubberRing is hard and does not fit exactly, so I attach a little Silicon grease. View detail

I wonder if I can fly by vibration

Cap of Handlebar Post of GSX - S1000 flew by vibration, so I bought this, but if inside diameter is a bit bigger Large, I can firmly insert it, but I feel a little loose.
I wish I could not fly again .... View detail

From the Plating of the NORMAL, he wanted to use the Lock nut of a Handle as a Chrome, and it was changed. It does not separate, but since it has stopped firmly, there is likely to be no fear of Dropping. although it is a part whi

From the Plating of the
NORMAL, he wanted to use the Lock nut of a Handle as a Chrome
, and it was changed.
It does not separate, but since it has stopped firmly, there is likely to be no fear of
Dropping. although it
is a part which is hard to notice -- delicate --
-- change which changed is felt.
It is recommended at a little Accent. View detail

[Webike Monitor] Many Color variationses can also be chosen according to liking. Since it is the foundations which are exchanged for a new thing once it removes [ ], if it is this price, I will think that a Cost performance is high.

[Webike Monitor] Many
Color variationses can also be chosen according to liking. Since it is the foundations which are exchanged for a new thing once it removes [
], if it is this price, I will think that a Cost performance is high. View detail