RAM Mount U-shaped Clamp

For now, I am using it for both GSX1300R HAYABUSA and GSX1300R HAYABUSA.

I will buy another one for CT110 HUNTER CUB later, but I also bought it for CT110 HUNTER CUB because I was worried that I would not be able to use it without Navigation.

The angle of the clamp is not that much of a concern, but I appreciate that I can install it without worrying about the angle, and since it is easy to remove except for the clamp, there are no problems other than a little bit of hassle for now as a dual use.

Even with vibration, I still haven't broken the Camera on my iPhone XS for Navigation. View detail

Purchase Repeat

I have been using it on my Ninja 1000 and found it to be sturdy and stable, so I decided to install it on my CUB as well.
Since the Meter visor with Bracket has already been installed on the CUB, the Quantity visor is installed on the Bracket part of the CUB.:Set
The U-shaped clamp came with two sizes, Large and Small, but the Small one was just right.

Quantity of all Arm and Mount (sold separately):When set, it is a little too large and tough for the CUB, but you can drive without worrying about it coming off!


Impressions of the Ram Mount purchase & darr;
https://imp.webike.net/article/453185/

Meter visor is this! ↓
https://www.webike.net/sd/24105239/

Meter visor imprints & darr;
https://imp.webike.net/article/505612/ View detail

For ActionCamera

Buy for ActionCamera and Navigation mounting
I already have it installed on my One Side, but bought it to install both ActionCamera and Navigation.
I hope it will be a record for Touring. View detail

Can be combined with parts for SystemUp

There is a wide variety of parts that you can combine and system up as you wish, so you can clamp what you want in the position and angle you want. The price of the parts is reasonable and the cost performance is satisfactory. View detail

Nut is recommended for purchase at Home Center.

Because I had YamatoCenter deliver to the destination of expedition, it was necessary to purchase Wrench at DaaSaw and the like because the hex size of Nut is 11mm as it is mentioned in the review of other people. However, when I look at the one which arrived, it may be called with Pilot, I cannot be installed in Handlebar because size does not fit in the first place with the one of Non-Penetrating as it is. What's going on with this? I had no choice, so I went to the home center's Koen PRO to find a nut that would fit. As a result, the nut of 1/4 was fit. Because most of the hexagonal size of Nut sold in Homsen is 10mm, it can be removed with general wrench. The thing itself is no problem at all, but it is a little difficult to insert the U-shaped clamp into the hole. But it came with some kind of grease to put in there. So I can recommend it, but I recommend you to buy it at Home Center for Nut only. View detail

I don't feel safe

This product was recommended to me by a friend of mine, but I've been buying it for Firmly and Case until now I was worried that the smartphone holder is not suitable for this type of smartphone I couldn't change to a smartphone holder with a pinch type
However, when I switched to this Ram Mount, I realized that the price is a little high, but the performance is worth it I could
I don't have to worry about slipping and shifting when driving on the highway or in the rain You can't stop the smartphone from being pinned down, but you can use it to stop the smartphone on top of it I think it is unlikely to be dropped because it is attached to the Seat of Rubber
The joint part can be changed by loosening the bolt that can be turned by hand, but the handlebar One pcJoint is placed between the point where the smartphone is fixed to the With the arm in between, you can adjust the position to suit you without shifting the fixed point You can
However, although the range of motion is wide, the orientation is related to the orientation of the Clamp that secures it to the bar It is better to have an image of the image you want to use before you install it I think
Moreover, I had attached it directly to the Handlebar at the time of purchase, but the Handlebar I bought the Brace and put it on there so I have more freedom than I ever had before

And the Type to put the Smartphone in the Case of the Type that I was using until now The difference between the two is that the body directly touches the controls when you stop and operate the device Easy to operate
The Smartphone used to get hot very quickly, but it would get hot and stuffy The smartphone no longer gets hot
It's important to note that it will get wet directly in the rain, so it is not waterproof It's about the only place where you have to be careful about the weather when using your Smartphone! View detail

FirmlyHold

I am using it for Handlebar of CB 400 SB. (Using Spacer)

Nut for fixing is probably Inch size, so ginger can be substituted with 11 mm Spanner.
Please note that at this time, be sure to prepare Spanner.
Nut and Rubber's Ball part are too close, so you can not enter Socket or Double-end Wrench.

Installation is completed if you tighten it strongly to the extent that it is not tame.

Ram Mount is very affordable and very strongly fixed to me.
Moreover, if you change the tip Parts, you can use it for various purposes such as smart Holder, NavigationHolder, CameraHolder.

It is a mount tool of Recommendation. View detail